Casio Projector XJ-A146 User Manual

							41
Plug and Play
(USB port 
models only)RCVHDWUNSingle Use this sub-menu to turn plug-and-play*1 on or off.
On*:
Select this option to turn on plug-and-play. This will allow the 
projector detect when an external USB device is connected and 
make that device the input source automatically.
Off:
Select this option to turn off plug-and-play.
USB Audio Out
(USB port 
models only)
RCVHDWUNSingle When playing back a movie file stored on a USB memory device, 
you can select audio output from the projector’s built-in speaker 
or to the line output.
Speaker*:
Select to output movie file audio from the speaker.
Line:
Select to output movie file audio from the AV terminal.
HDMI Audio 
Out
RCVHDWUNSingle Specifies whether the input audio signal should be output from the 
projector’s built-in speaker or to the line output.
Speaker*:
Outputs the audio signal being input to the HDMI port from the 
speaker.
Line:
Outputs the audio signal being input to the HDMI port from the 
AV terminal.
High Altitude
RCVHDWUNSingle Use this sub-menu to turn the high-altitude fan speed setting on or 
off in accordance with the altitude of the area where you are using 
the projector.
On:
Select this setting when using the projector in a high altitude 
(1,500 to 3,000 meters above sea level) area where air is thin. 
This setting increases cooling efficiency.
Off*:
Select this setting at normal altitudes (up to 1,500 meters).
Important!Do not use this projector at altitudes greater than 
3,000 meters above sea level.
Timer Function
RCVHDWUNSingle Selecting this item displays the timer function menu. For details, 
see “Presentation Timer” (page 21).
Restore Menu 
Defaults
RCVHDWUNSingle This sub-menu returns all of the sub-menu items on the Option 
Settings 2 main menu to their initial default settings.
*1 When plug-and-play is turned on, the projector will make that device the input source 
automatically. For details about plug-and-play, see “USB Function Guide” on the bundled 
CD-ROM.
Setting NameInputSetting UnitDescription 
						

							42
USB Settings Main Menu (USB Port Models Only)
The USB Settings main menu is available only when there is an external device connected to the USB 
port of the projector. For details, see “USB Function Guide” on the bundled CD-ROM.
Wireless Main Menu (USB Port Models Only)
The Wireless main menu is available only when “Wireless” is selected as the input source on the 
projector. For more information, see the “Wireless Function Guide” on the CD-ROM that comes with 
the projector.
Operational Info Main Menu
Restore All Defaults Main Menu
Setting NameInputSetting UnitDescription
Input Signal
RCVHDWUNSource 
SpecificThis sub-menu item shows the currently selected input signal 
(RGB, Component, Video, HDMI (PC), or HDMI (DTV)). “- - - -” is 
indicated here when there is no input signal.
Signal Name
RCVHDUSource 
SpecificThis sub-menu item shows the signal name of the signal being 
input to the projector. For details about signal names, see “Signal 
Name” under “Supported Signals” (page 53).
Resolution
RHSource 
SpecificThis sub-menu item appears only when RGB is the input signal. It 
shows the number of vertical and horizontal pixels of resolution of 
the RGB or HDMI (PC) input signal.
Horizontal 
Frequency
RCVHDSource 
SpecificThis sub-menu item shows the horizontal frequency of the input 
signal.
Vertical 
Frequency
RCVHDSource 
SpecificThis sub-menu item shows the vertical frequency of the input 
signal.
Scan System
RCHDSource 
SpecificThis sub-menu item appears only when RGB, Component, 
HDMI (PC), or HDMI (DTV) is the input signal, and shows the scan 
system of the input signal. The scan system is interlace or 
non-interlace for an RGB or HDMI (PC) signal input, and interlace 
or progressive for a component or HDMI (DTV) signal input.
Light Time
RCVHDWUNSingle This sub-menu item shows the cumulative number of hours the 
current light source unit has been used to date.
Setting NameInputSetting UnitDescription
Unit Operating 
Time
RCVHDWUNSingle This sub-menu item shows the cumulative operating time of this 
unit. This time cannot be initialized.
Restore All 
Defaults
RCVHDWUNSingle This sub-menu returns all sub-menu items on all main menus to 
their initial default settings. This operation can be performed 
regardless of the currently selected input source and regardless 
of whether or not a signal is currently being input. For details 
about this procedure, see “To restore all settings on the setup 
menu to their initial factory defaults” on page 32.
B 
						

							43
Cleaning the Projector
Periodically clean the projector exterior, lens, intake vents, and exhaust vents on a regular basis.
Important!Before cleaning the projector, be sure to unplug it from the power outlet and make sure it is 
cooled down completely.
Wipe the exterior of the projector with a soft cloth that has been moistened in a weak solution of water 
and a mild neutral detergent. Be sure to wring all excess moisture from the cloth before wiping.
Never use benzene, alcohol, thinner, or any other volatile agent for cleaning.
Carefully wipe the lens with a commercially available lens cloth or optical lens paper, like those for 
eyeglasses or camera lenses. When cleaning the lens, do not apply undue force and take care to avoid 
damaging the lens.
Dust and dirt tend to collect around the intake vents. Because of this, you should use a vacuum 
cleaner to clean away accumulated dust and dirt periodically as shown below.
Important!zContinued use of the projector after dust has accumulated around the intake vents can cause 
overheating of internal components and lead to malfunction.
zCertain operating conditions also can cause dirt and dust to accumulate around the 
projector’s exhaust vents. If this happens, use the same procedure as that described above to 
clean the exhaust vents.
Cleaning the Projector Exterior
Cleaning the Lens
Cleaning Intake and Exhaust Vents 
						

							44
Troubleshooting
Indicators keep you informed about the current operational status of the projector. The following 
shows what the indicators look like when operation is normal.
When a warning message appears on the projection screen, or when the POWER/STANDBY, LIGHT, 
and TEMP indicators are lit or flashing in a pattern other than those shown above, it means that a 
projector error has occurred. For details, see “Error Indicators and Warning Messages” (below).
Warning messages and indicators let you know what the problem is when a projector error occurs.
When an error occurs, wait until the fan stops before unplugging the AC power cord. If you unplug the 
AC power cord while the fan is still operating, an error may occur when you plug the AC power cord 
back in.
Indicators
When the indicators appear 
like this:It means this:
POWER/
STANDBYLIGHT TEMPYou have just plugged the AC power cord into a power outlet. Wait 
until the projector enters the standby state (see below) before trying 
to turn on power. zzz
Amber Amber Amber
zccStandby state: The AC power cord is plugged in and the projector is 
in standby.
Amber
zzProjector is warming up after being turned on.
Green Amber Amber
zccProjector is on and standing by for use.
Green
ccProjector is performing internal power down processes.
Amber
zzc“On (Auto)” or “On (Manual)” is selected for the projector’s Eco Mode 
(page 23) setting.
Green Green
z : Lit : Flashingc : Unlit
Error Indicators and Warning Messages
Indicator/Error MessageDescription and Required Action
POWER : Green steady The projector’s internal temperature is very high. Press the [ESC] key to 
clear the warning message and perform the following steps.
1Check for any blocking of the projector’s intake vents and exhaust 
vents, and make sure that there is sufficient space around the 
projector. See 
“Setup Precautions” (page 10).
2If there is dust accumulated around the intake vents and/or exhaust 
vents, turn off the projector and remove it. See 
“Cleaning the 
Projector” (page 43). LIGHT : –
TEMP : –
Message : Internal temperature is too 
high. Check projector air 
vents for blockage. 
						

							45
POWER : Amber flashingJ 
Amber steadyPower has turned off automatically due to internal overheating. Perform 
the following steps.
1Check for any blocking of the projector’s intake vents and exhaust 
vents, and make sure that there is sufficient space around the 
projector. See 
“Setup Precautions” (page 10).
2If there is dust accumulated around the intake vents and/or exhaust 
vents, remove it. See 
“Cleaning the Projector” (page 43).
If there is no problem with the projector’s vents, confirm that the POWER/
STANDBY indicator is lit amber (without flashing), and then turn power 
back on again. If the error occurs again when you turn power back on, 
contact your retailer or nearest authorized CASIO Service Center. LIGHT : –
TEMP : –
Message : Internal temperature is too 
high. The projector will 
turn off.
POWER : Amber flashingJ 
Red steadyPower has turned off automatically due to internal overheating. This 
causes a dialog box containing the text in the next item below to appear 
the next time you turn on the projector. Follow the steps that are 
provided. LIGHT : –
TEMP : Red flashing 
(0.5-second interval)
Message : –
POWER : Green steady The last time you were using the projector, power turned off automatically 
due to internal overheating. Press the [ESC] key to clear the warning 
message and perform the following steps.
1Check for any blocking of the projector’s intake vents and exhaust 
vents, and make sure that there is sufficient space around the 
projector. See 
“Setup Precautions” (page 10).
2If there is dust accumulated around the intake vents and/or exhaust 
vents, turn off the projector and remove it. See 
“Cleaning the 
Projector” (page 43).
3Disconnect the power cord from the projector and wait for all of the 
projector’s indicators to go out. Next, reconnect the power cord and 
turn the projector back on. If the error occurs again when you turn 
power back on, contact your retailer or nearest authorized CASIO 
Service Center. LIGHT : –
TEMP : –
Message : The projector has a 
history of turning off due 
to high temperature. 
Check air vents for 
blockage.
POWER : Amber flashingJ 
Red steadyPower has turned off automatically due to a fan problem. Confirm that the 
POWER/STANDBY indicator is lit red (without flashing) and that the fan 
has stopped. After checking the POWER/STANDBY indicator, disconnect 
the power cord from the projector and wait for all of the projector’s 
indicators to go out. Next, reconnect the power cord and turn projector 
power back on.
If the error occurs again when you turn power back on, contact your 
retailer or nearest authorized CASIO Service Center. LIGHT : Red steady
TEMP : Red steady
Message : There is a problem with 
the fan. The projector will 
turn off.
POWER : Amber flashingJ 
Red steadyPower has turned off automatically due to a system problem. After 
confirming that the POWER/STANDBY indicator is lit red (without 
flashing), disconnect the power cord from the projector and wait for all of 
the projector’s indicators to go out. Next, reconnect the power cord and 
turn the projector back on.
If the error occurs again when you turn power back on, contact your 
retailer or nearest authorized CASIO Service Center. LIGHT : –
TEMP : Red steady
Message : A system problem has 
occurred. The projector 
will turn off.
Indicator/Error MessageDescription and Required Action 
						

							46
POWER : Green steady A system problem has occurred, which may cause problems with some 
functions. Turn off the projector, disconnect the power cord from the 
projector and wait for all of the projector’s indicators to go out. Next, 
reconnect the power cord and turn the projector back on.
If the error occurs again when you turn power back on, contact your 
retailer or nearest authorized CASIO Service Center.
Press the [ESC] key to clear the warning message. LIGHT : –
TEMP : –
Message : A system problem has 
occurred. Normal 
projection is not possible.
POWER : Green steady
LIGHT : –
TEMP : –
Message : There is some problem 
with the system.
The audio function may 
not operate correctly.
POWER : Green steady The USB connection was terminated because of a problem with the USB 
port. To use the USB function, turn off the projector and then turn it back 
on again.
If the error occurs again when you turn power back on, contact your 
retailer or nearest authorized CASIO Service Center.
Press the [ESC] key to clear the warning message. LIGHT : –
TEMP : –
Message : There is a problem with 
the USB port.
POWER : Green steady Zoom and focus cannot be performed due to some trouble in the optical 
drive circuit. Turn off the projector and then turn it back on again.
If the error occurs again when you turn power back on, contact your 
retailer or nearest authorized CASIO Service Center.
Press the [ESC] key to clear the warning message. LIGHT : –
TEMP : –
Message : Zoom and focus cannot 
be performed for some 
reason. Try turning the 
projector off and then 
back on again.
If this message reappears, 
request servicing.
POWER : Amber flashingJ 
Red steadyThe projector was turned off automatically due to some problem that was 
probably caused by external digital noise or some other reason. Confirm 
that the POWER/STANDBY indicator is lit red (without flashing). After 
checking the POWER/STANDBY indicator, disconnect the power cord 
from the projector and wait for all of the projector’s indicators to go out. 
Next, reconnect the power cord and turn projector power back on.
If the error occurs again when you turn power back on, contact your 
retailer or nearest authorized CASIO Service Center. LIGHT : –
TEMP : Red steady
Message : –
POWER : Amber flashingJ 
Red steadyThe projector was turned off automatically because the light source unit 
turned off or did not turn on. After confirming that the POWER/STANDBY 
indicator is lit red (without flashing), unplug the power cord. Wait for a 
short while and then plug it back in and turn on the projector again.
If the error occurs again when you turn power back on, contact your 
retailer or nearest authorized CASIO Service Center. LIGHT : Red flashing 
(0.5-second interval)
TEMP : Red flashing 
(0.5-second interval)
Message : –
Indicator/Error MessageDescription and Required Action 
						

							47
Check the following items whenever you experience any problem with the projector.
POWER : Amber flashingJ 
Red steadyPower has turned off automatically due to a projector memory error. 
Confirm that the POWER/STANDBY indicator is lit red (without flashing). 
After checking the POWER/STANDBY indicator, disconnect the power 
cord from the projector and wait for all of the projector’s indicators to go 
out. Next, reconnect the power cord and turn projector power back on.
If the error occurs again when you turn power back on, contact your 
retailer or nearest authorized CASIO Service Center. LIGHT : Not lit or red flashing
TEMP : Red flashing 
(2-second interval)
Message : –
POWER : Amber flashingJ 
Red steadyPower has turned off automatically because the light source unit cover is 
open. Perform the following steps.
1After confirming that the POWER/STANDBY indicator is lit red (without 
flashing), disconnect the power cord from the projector.
2Check to make sure that the light source unit cover is closed.
3Plug the power cord back in and turn the projector back on again.
If the error occurs again when you turn power back on, contact your 
retailer or nearest authorized CASIO Service Center. LIGHT : –
TEMP : Amber flashing 
(1-second interval)
Message : –
Projector Troubleshooting
ProblemCause and Recommended Action
Power does not turn on.zIf the POWER/STANDBY indicator is not lit, the AC power cord is not connected 
correctly. Connect the AC power cord correctly.
zIf the TEMP or LIGHT indicator remains flashing or lit, it means some type of error 
has occurred. See “Error Indicators and Warning Messages” (page 44).
No image is projected or 
the projected image is 
abnormal.zThe computer or video device connected to the projector is not turned on or it is 
not outputting a video signal. Make sure the connected computer or video device 
is turned on, and perform the required operation on it to output a video signal.
zThe correct output source is not selected on the projector. On the projector, select 
the correct input source that corresponds to the connected device.
zImages may not project correctly when you have the component output terminal of 
a video device connected to the COMPUTER terminal of the projector. Connect to 
the AV terminal of the projector.
Image color or display is 
very abnormal.The wrong option (“Component” or “RGB”) may be selected for the “Input SettingsJ 
COMPUTER Terminal” setting on the setup menu. The image will not be projected 
correctly if “Component” is selected while the projector’s COMPUTER terminal is 
connected to the RGB output terminal of a computer, or if “RGB” is selected while the 
projector’s COMPUTER terminal is connected to the component video output 
terminal of a video device. On the setup menu, select “Auto” for the “Input SettingsJ 
COMPUTER Terminal” setting. See page 38.
I can’t understand 
messages or menus 
because they are the 
wrong language.Perform the following operation to select the language you want. See page 40.
1. Press the [MENU] key to display the setup menu.
2. If the input signal is HDMI, press [T] four times and then press the [ENTER] key. If 
the input signal is not HDMI, press [T] five times and then press the [ENTER] key.
3. Press [S] twice and then press the [ENTER] key to display the language selection 
menu.
4. Use the [T] and [S] keys to move the highlighting to the language you want to 
select and then press the [ENTER] key.
5. Press the [MENU] key to exit the setup menu.
Indicator/Error MessageDescription and Required Action 
						

							48
Important!zTry performing the following steps, which may or may not return the projector to normal 
operation.
zIf normal operation does not resume after you perform the above steps, take the projector to 
your retailer or authorized CASIO service center.
No soundzThe projector’s volume level setting may be too low or muted. Press the remote 
controller [VOLUME] key and then use [W] and [X] to adjust the volume level. See 
page 20.
zThe volume level setting of the device connected to the projector is too low or the 
other device is not outputting audio. Adjust the volume level of the connected 
device.
zThe audio output of the connected device may not be connected correctly to the 
projector’s AV terminal. Check the connection, referring to one of the following 
(depending on the type of connected device): “Connecting the Analog RGB Output 
of a Computer to the Projector” (page 11) or “Connecting to a Video Device” 
(page 13).
zWhen a video device’s or computer’s HDMI output is connected to the HDMI port 
of the projector, “Line” may be selected for the “Option Settings 2J HDMI Audio 
Out” setting on the setup menu. Change the “HDMI Audio Out” setting to 
“Speaker”. See page 41.
Strange color The input signal may not match projector settings. Try doing the following.
– Use the [BRIGHT] key to adjust image brightness.
– Use the [COLOR MODE] key to change the color mode.
– On the setup menu, use “Image Adjustment 1J Color Balance” to adjust the 
projection image color balance.
Text is blurry.zThe image may be out of focus. On the remote controller, use the [FOCUSS] and 
[FOCUST] keys to adjust image focus.
zThe current frequency and/or phase setting do not match the input signal. (Applies 
only when the input source is an RGB signal.) Press the [AUTO] key to execute an 
automatic adjustment operation.
zOn the setup menu, perform the “Image Adjustment 2J Frequency” and “Image 
Adjustment 2J Phase” adjustments. (Applies only when the input source is an 
RGB signal.) See page 35.
zIf the input source is a video camera or document camera, check to make sure 
there is no problem with the input source device.
The message “Please input 
the password.” appears 
and further operation is not 
possible.The “Option Settings 1J Power On Password” setting on the setup menu is turned 
on, so the projector is password protected. Input the correct password, and then 
press the [ENTER] key. See page 28.
The remote controller does 
not work.zThe remote controller batteries may be dead. Replace the batteries.
zThe remote controller may be too far from the projector. Make sure the remote 
controller is within the allowable range when you operate it. See page 49.
The TEMP or LAMP 
indicator is flashing or lit.An error occurred. See “Error Indicators and Warning Messages” (page 44).
The light source unit does 
not light.The light source unit has reached the end of its service life or it is malfunctioning. 
Contact your original dealer or authorized CASIO service center for replacement.
1. Unplug the AC power cord and wait for at least 10 minutes.
2. Plug the power cord back in and turn the projector back on again.
ProblemCause and Recommended Action 
						

							49
Appendix
When performing an operation on the remote controller, point it at the remote control signal receiver 
on the back or front of the projector. The following illustration shows the range of the remote controller 
signal.
Remote Controller Range
zThe range of the remote controller may be narrower and/or shorter than that shown on the right 
(Back) when there is a special AV cable plugged into the AV terminal on the back of the projector.
zThe allowable distance between the remote controller and the projector is less when there is a 
sharp angle between the remote controller and the remote control signal receiver.
Important!To avoid running down the batteries, store the remote control unit so its keys are not pressed 
inadvertently.
Remote Controller Signal Range
Front
±
30 degrees max.
5 meters (16.4 feet) 
max.
5 meters (16.4 feet) max.
Back
5 meters (16.4 feet) 
max.5 meters (16.4 feet) 
max.
±
30 degrees max.±
30 degrees max.
5 degrees to 
30 degrees 
						

							50
The following table shows the relationship between the distance and projected image size.
*h = Height from the center of the lens to the bottom edge of the projection screen.
Important!Note that the distances provided above are for reference only.
Projection Distance and Screen Size
Projection SizeApproximate Projection Distance
XJ-A141/XJ-A146XJ-A241/XJ-A246/XJ-A251/XJ-A256
Screen 
SizeDiagonal
(cm)Minimum 
Distance
(m / feet)Maximum 
Distance
(m / feet)h*Minimum 
Distance
(m / feet)Maximum 
Distance
(m / feet)h*
(cm / inch)
40 102 1.1 / 3.61 2.2 / 7.22 0 1.0 / 3.28 1.9 / 6.23 9 / 3.54
60 152 1.7 / 5.58 3.4 / 11.15 0 1.4 / 4.59 2.8 / 9.19 14 / 5.51
80 203 2.3 / 7.55 4.5 / 14.76 0 1.9 / 6.23 3.8 / 12.47 18 / 7.09
100 254 2.8 / 9.19 5.6 / 18.37 0 2.4 / 7.87 4.8 / 15.75 23 / 9.06
150 381 4.3 / 14.11 8.5 / 27.89 0 3.6 / 11.81 7.2 / 23.62 34 / 13.39
200 508 5.7 / 18.70 11.3 / 37.07 0 4.8 / 15.75 9.6 / 31.50 45 / 17.72
h*