Casio Exilim Zoom Ex Z450 Users Guide

							81Advanced Settings
Procedure
[r] (REC) * [MENU] * Quality Tab * ISO
For details, see the Control Panel procedure on page 36.
Procedure
[r] (REC) * [MENU] * Quality Tab * Metering
The metering mode determines what part of the subject is metered for exposure.
• The currently selected metering mode is indicated by an icon on the snapshot 
screen. No icon is displayed when “B Multi” is selected as the metering mode.
Procedure
[r] (REC) * [MENU] * Quality Tab * Lighting
For details, see the Control Panel procedure on page 35.
Specifying ISO Sensitivity (ISO)
Specifying the Metering Mode (Metering)
 MultiMulti-pattern metering divides the image into sections and 
measures the light in each section for a balanced exposure reading. 
This type of metering provides error-free exposure settings for a 
wide range of shooting conditions.
 Center 
WeightedCenter weighted metering concentrates on the center of the focus 
area to measure light. This type of metering is best when you want 
some level of control over contrast.
 SpotSpot metering takes readings at a very small area. Use this 
metering method when you want exposure to be set according to 
the brightness of a particular subject, without being affected by 
surrounding conditions.
Optimizing Image Brightness (Lighting)
B
N
˜
Downloaded From camera-usermanual.com Casio Manuals 
						

							82Advanced Settings
Procedure
[r] (REC) * [MENU] * Quality Tab * Color Filter
Settings: Off, B/W, Sepia, Red, Green, Blue, Yellow, Pink, and Purple
Procedure
[r] (REC) * [MENU] * Quality Tab * Sharpness
You can specify one of five sharpness settings from +2 (sharpest) to –2 (least sharp).
Procedure
[r] (REC) * [MENU] * Quality Tab * Saturation
You can specify one of five saturation settings from +2 (most saturated) to –2 (least 
saturated).
Procedure
[r] (REC) * [MENU] * Quality Tab * Contrast
You can specify one of five contrast settings from +2 (most contrast between light and 
dark) to –2 (least contrast between light and dark).
Procedure
[r] (REC) * [MENU] * Quality Tab * Flash Intensity
You can specify one of five flash intensity settings, from –2 (weakest) to +2 
(strongest).
• Flash intensity may not change when the subject is too far away or too close.
Using Built-in Color Filters (Color Filter)
Controlling Image Sharpness (Sharpness)
Controlling Color Saturation (Saturation)
Adjusting Image Contrast (Contrast)
Specifying Flash Intensity (Flash Intensity)
Downloaded From camera-usermanual.com Casio Manuals 
						

							83Viewing Snapshots and Movies
Viewing Snapshots and Movies
See page 25 for the procedure for viewing snapshots.
1.Press [p] (PLAY) and then use [4] and [6] to display the movie you 
want to view.
2.Press [SET] to start playback.
Movie Playback Controls
• Playback may not be possible for movies not recorded with this camera.
Viewing Snapshots
Viewing a Movie
Fast forward/
fast reverse[4] [6]
• Each press of either button increases the speed of the fast 
forward or fast reverse operation.
• To return to normal playback speed, press [SET].
Play/pause[SET]
1 frame forward/
back[4] [6]
• Holding down either button scrolls continuously.
Volume 
adjustmentPress [2] and then press [8] [2]
• Volume can be adjusted only while movie playback is in 
progress.
Information 
display on/off[8] (DISP)
ZoomSlide the zoom controller in the direction of z ([).
• You can use [8], [2], [4], and [6] to scroll the zoomed 
image on the monitor screen. You can zoom a movie image 
up to 4.5 times normal size.
Stop playback[MENU]
Movie icon: »
Image quality Recording time
Downloaded From camera-usermanual.com Casio Manuals 
						

							84Viewing Snapshots and Movies
Each time you perform a continuous shutter (CS) operation, the camera creates a CS 
group that includes all of the images for that particular CS session. You can use the 
following procedure to play back the images in a particular CS group.
1.Press [p] (PLAY) and then use [4] and [6] to display the CS group 
whose images you want to view.
2.Press [SET] to start playback the images in the CS group.
This will play back the images in the CS group you selected.
Playback Controls
Viewing Continuous Shutter Images
[4] [6]During playback, changes the playback direction and playback speed.
While playback is paused, scrolls forward or back.
• Playback speed cannot be adjusted while the displayed image is 
zoomed.
[SET]Toggles between pause and play.
Zoom 
controllerZooms the image.
• You can use [8], [2], [4], and [6] to scroll the zoomed image on 
the monitor screen.
[MENU]Exits CS group playback.
[8] (DISP)Cycles through information display formats.
[2]Displays the delete menu.
Number of image files
in the CS group
First image in the CS groupCS group icon
Current image number/
number of images in
the group
Playback guide
Downloaded From camera-usermanual.com Casio Manuals 
						

							85Viewing Snapshots and Movies
NOTE
• Multiple images shot using “CS: Normal Speed CS” are stored individually and are 
not grouped. This means they can be displayed individually (page 25) but not as a 
CS group.
You can use the following procedures to delete images while playback is in progress 
or paused.
.Deleting a Specific CS Group File
1.While CS image playback is in progress or paused, press [2].
2.Use [4] and [6] to display the image you want to delete.
3.Use [8] and [2] to select “Delete” and then press [SET].
• To delete other files, repeat steps 2 and 3.
• To exit the delete operation, press [MENU].
.Deleting All Files in a CS Group
1.While CS image playback is in progress or paused, press [2].
2.Use [8] and [2] to select “Del Group Images” and then press [SET].
3.Use [8] and [2] to select “Yes”, and then press [SET].
Deleting Continuous Shutter Images
Downloaded From camera-usermanual.com Casio Manuals 
						

							86Viewing Snapshots and Movies
Use the following to divide up a CS Group into individual images.
.Dividing Up a Specific CS Group
1.While a CS group folder is displayed, press [MENU].
2.Use [4] and [6] to select “PLAY” tab.
3.Use [8] and [2] to select “Divide Group” and then press [6].
4.Use [4] and [6] to display the CS group folder whose CS group you 
want to divide up.
5.Use [8] and [2] to select “Divide” and then press [SET].
• To divide up other CS group files, repeat steps 4 and 5.
.Dividing Up All CS Groups
1.While a CS group folder is displayed, press [MENU].
2.Use [4] and [6] to select “PLAY” tab.
3.Use [8] and [2] to select “Divide Group” and then press [6].
4.Use [8] and [2] to select “Divide All Groups” and then press [SET].
5.Use [8] and [2] to select “Yes”, and then press [SET].
• Once a CS group is divided, it cannot be regrouped.
Dividing Up a CS Group
Downloaded From camera-usermanual.com Casio Manuals 
						

							87Viewing Snapshots and Movies
1.In the PLAY mode, use [4] and [6] to scroll through the images until 
the one you want is displayed.
2.Slide the zoom controller towards z ([) to 
zoom.
You can use [8], [2], [4], and [6] to scroll the 
zoomed image on the monitor screen. Slide the 
zoom controller towards w to unzoom the image.
– When monitor screen contents are turned on, a 
graphic in the lower right corner of the screen 
shows what part of the zoomed image is 
currently displayed.
– To exit the zoom screen, press [MENU] or [BS].
– Though the maximum image zoom factor is 8X, 
certain image sizes may not allow zooming up 
to the full 8X.
• Pressing [SET] will lock the current zoom factor for the on-screen image. You 
can then use [4] and [6] to scroll between images, using the same zoom 
factor. Pressing [SET] again will unlock the zoom factor and allow you to use 
[8], [2], [4] and [6] to move around the currently displayed images.
Zooming an On-screen Image
Image area
Current display areaZoom factor
Downloaded From camera-usermanual.com Casio Manuals 
						

							88Viewing Snapshots and Movies
1.In the PLAY mode, slide the zoom controller 
towards w (]).
Use [8], [2], [4] and [6] to move the selection 
boundary around the image menu.
To view a particular image, use [8], [2], [4], or [6] to 
move the selection boundary to the image you want 
and then press [SET].
1.In the PLAY mode, slide the zoom controller towards w (]) twice.
This will display the calendar screen that shows the first image recorded on each 
day.
To display the first image recorded on a particular day, 
use [8], [2], [4], and [6] to move the selection 
boundary to the day you want and then press [SET].
To exit the calendar screen, press [MENU] or [BS].
• If you save an image using any one of the following 
functions, the image will appear in the calendar on the 
date that you last saved it.
Lighting, White Balance, Brightness, Keystone Correction, Color Restoration, 
Resizing, Cropping, Copy, Layout Print, MOTION PRINT
If you edit the date and time of an image, the image still will appear on the date 
it was originally recorded.
Displaying the Image Menu
Displaying Images in the Calendar Screen
Boundary
Downloaded From camera-usermanual.com Casio Manuals 
						

							89Viewing Snapshots and Movies
1.Use the AV cable that comes with the camera to connect it to the TV.
• Make sure that you insert the cable connector into the 
USB/AV port until you feel it click securely into place. 
Failure to insert the connector fully can result in poor 
communication or malfunction.
• Note that even while the connector is fully inserted, you 
still will be able to see the metal part of the connector as shown in the 
illustration.
2.Turn on the TV and select its video input mode.
If the TV has more than one video input, select the one where the camera is 
connected.
3.Press [p] (PLAY) to turn on the camera.
This will cause an image to appear on the TV screen, without anything appearing 
on the camera’s monitor screen.
• Pressing [ON/OFF] or [r] (REC) will not turn on the camera while the AV 
cable is connected.
• You also can change the aspect ratio of the screen and the video output 
system (page 145).
Viewing Snapshots and Movies on a TV Screen
Yellow
AV cable (bundled)
USB/AV port White
Making sure that the 6 mark on the camera is aligned with the 4 mark of the AV 
cable connector, connect the cable to the camera.
Audio Video
VIDEO IN jack (yellow)AUDIO IN jacks (white)
TV
Downloaded From camera-usermanual.com Casio Manuals 
						

							90Viewing Snapshots and Movies
4.Now you can display images and play back movies as you normally do.
IMPORTANT!
• Before connecting to a TV to display images, be sure to configure the camera’s 
[r] (REC) and [p] (PLAY) buttons for “Power On” or “Power On/Off” (page 144).
• Audio is initially output by the camera at maximum volume. When you first start 
displaying images, set the TV volume control at a relatively low level and then 
adjust it as required.
NOTE
• Audio is monaural.
• Certain TVs may cut off part of the images.
• All icons and indicators that appear on the monitor screen also appear on the TV 
screen. You can use [8] (DISP) to change the display contents.
Recording Camera Images to a DVD Recorder or Video Deck
Use one of the following methods to connect the camera to the recording device 
using the camera’s bundled AV cable.
– DVD recorder or video deck: Connect to the VIDEO IN and AUDIO IN terminals.
– Camera: USB/AV port
You can play a slideshow of snapshots and movies on the camera and record it on a 
DVD or video tape. You can record movies by selecting “» Only” for the slideshow 
“Images” setting (page 91). When recording images to an external device, use [8] 
(DISP) to clear all indicators from the monitor screen (page 147).
For information about connecting a monitor to the recording device and about how to 
record, see the user documentation that comes with the recording device you are 
using.
Downloaded From camera-usermanual.com Casio Manuals