Casio Exilim Ex Z5 Users Guide

							PLAYBACK
141
Playing a Slideshow
A slideshow automatically plays back images in sequence
at a fixed interval.
1.In the PLAY mode, press [MENU].
2.Select the “PLAY” tab, select “Slideshow”,
and then press [].
•The file displayed on the calendar for each date is
the first file that was recorded on that date.
•To exit the calendar screen, press [MENU] or [BS].
•On the calendar screen, 
 indicates a voice
recording file (page 147).
•
 appears in place of the image when the date
contains data that cannot be displayed by this
camera.
2.Use [
], [], [], and [] to move the
selection boundary to the date you want, and
then press [SET].
•This displays an image of the first file that was
recorded on the selected date.
Downloaded From camera-usermanual.com Casio Manuals 
						

							PLAYBACK
142
4.Use [
] and [] to select “Start”, and then
press [SET].
•This starts the slideshow.
5.To stop the slideshow, press [SET].
•The slideshow will also stop automatically after the
amount of time you specified for “Time” elapses.
Effect
•Pattern 1, 2, 3, 4
Applies a preset effect when transitioning from
one image to another.
•Random
Randomly applies the preset patterns (1, 2, 3,
and 4).
•OFF
Effects turned off.3.Use the screen that appears to configure the
image, time, interval, and effect settings.
Images
Time
Interval•All Images
Displays all images in camera memory.
•
 OnIy
This icon appears only in the case of
snapshots and audio snapshots.
•
 OnIy
This icon appears only in the case of movies.
•One Image
Displays a particular image.
•Favorites
Displays all images in the FAVORITE folder.
Use [] and [] to specify the playback time you
want (1 to 5 minutes, or 10, 15, 30, or 60
minutes).
Use [] and [] to specify the interval you want
(MAX, or 1 to 30 seconds).
•When playback reaches a movie file while
“MAX” is selected as the interval, only the first
frame of the movie is displayed.
Downloaded From camera-usermanual.com Casio Manuals 
						

							PLAYBACK
143
•Note that effect settings are disabled when the
slideshow “Images” setting is “Favorites” or “
Only”, or when the slideshow “Interval” setting is
“MAX”, “1 sec”, or “2 sec”.
•Images copied from another digital camera or a
computer may take longer time to appear than the
slideshow interval time you specify.
•If there are indicators on the display, you can clear
them by pressing [
] (DISP) (page 29).
•When the slideshow reaches a movie while “One
Image” is selected for “Images”, the movie will repeat
playback for the time specified by for “Time”.
 IMPORTANT! 
•Note that all buttons are disabled while an image
change is in progress. Wait until an image is stopped
on the monitor screen before performing a button
operation, or hold down the button until the image
stops.
•Pressing [] during a slideshow will scroll to the
previous image, while [] scrolls to the next image.
•When the slideshow comes to a movie file, it plays
the movie and its audio once.
•When the slideshow comes to a voice recording file
or an audio snapshot, it plays the audio once.
•The audio of movies, audio snapshots, and voice
recording files is not played when “MAX” is specified
for the slideshow “Interval” setting. With all other
“Interval” settings, movies and all audio (movies,
audio snapshots, voice recording files) are played
back, regardless of their length.
•During audio playback, you can adjust volume by
pressing [] and then using [
] and [].
Downloaded From camera-usermanual.com Casio Manuals 
						

							PLAYBACK
144
4.Use [
] and [] to
select “Rotate”, and
then press [SET].
•Each press of [SET]
rotates the image 90
degrees.
5.After you are finished configuring settings,
press [MENU] to exit the setting screen.
Rotating the Display Image
Use the following procedure to rotate the image 90 degrees
and register the rotation information along with the image.
After you do this, the image is always displayed in its
rotated orientation.
1.In the PLAY mode, press [MENU].
2.Select the “PLAY” tab, select “Rotation”, and
then press [].
•Note that this operation is possible only when a
snapshot image is on the monitor screen.
3.Use [] and [] to scroll through images until
the one you want to rotate is on the monitor
screen.
Downloaded From camera-usermanual.com Casio Manuals 
						

							PLAYBACK
145
Adding Audio to a Snapshot
The “after-recording” feature lets you add audio to
snapshots after they are recorded. You can also re-record
the audio of an audio snapshot (one with a 
 icon on it).
•Audio Format: WAVE/ADPCM recording format
This is the Windows standard format for audio recording.
The file extension of a WAVE/ADPCM file is “.WAV”.
•Recording Time:
Up to about 30 seconds per image
•Audio File Size:
Approximately 165KB (30-second recording of
approximately 5.5KB per second)
 IMPORTANT! 
•You cannot rotate an image that is protected. To
rotate such an image, first unprotect it.
•You may not be able to rotate a digital image that
was recorded with another type of digital camera.
•You cannot rotate the following types of images.
—Movie images and the voice recording file icon
—Images created with MOTION PRINT
•Image rotation is supported for single image only.
You cannot rotate a 9-image screen, an image on
the calendar screen, or a zoomed image.
Downloaded From camera-usermanual.com Casio Manuals 
						

							PLAYBACK
146
To re-record audio
1.In the PLAY mode, use [] and [] to scroll
through snapshots until the one whose audio
you want to re-record is displayed.
2.Press [MENU].
3.Select the “PLAY” tab, select “Dubbing”, and
then press [].
4.Use [
] and [] to select “Delete”, and then
press [SET].
•If you merely want to delete the audio without re-
recording, press [MENU] here to complete the
procedure.
5.Press the shutter button to start audio
recording.
6.Recording stops after about 30 seconds or
when you press the shutter button.
•This deletes the existing audio and replaces it with
the new one.
1.In the PLAY mode, use [] and [] to scroll
through snapshots until the one to which you
want to add audio is displayed.
2.Press [MENU].
3.Select the “PLAY”
tab, select “Dubbing”,
and then press [].
4.Press the shutter button to start audio
recording.
5.Recording stops after about 30 seconds or
when you press the shutter button.
Downloaded From camera-usermanual.com Casio Manuals 
						

							PLAYBACK
147
 IMPORTANT! 
•Take care that you do
not block the
microphone with your
fingers.
•Good recording results
are not possible when
the camera is too far
from the subject.
•The 
 (Audio) icon appears on the monitor screen
after audio recording is complete.
•You will not be able to record audio when remaining
memory capacity is low.
•You cannot add audio to the following types of
images.
—Movie images
—Images created with MOTION PRINT
—Protected snapshot (page 155)
•Audio that is re-recorded or deleted cannot be
recovered. Make sure you no longer need audio
before re-recording or deleting it.
Playing Back a Voice Recording File
Perform the following steps to play back a voice recording
file.
1.In the PLAY mode, use [] and [] to display
the voice recording file (a file with 
 on it)
you want to play.
2.Press [SET].
•This starts playback of
the voice recording file
through the camera’s
speaker.
•You can perform the
following operations
while audio is playing.
Microphone
Downloaded From camera-usermanual.com Casio Manuals 
						

							PLAYBACK
148
Displaying Camera Images on a TV Screen
You can display recorded images on a TV screen and even
use a TV screen to compose images before you record
them. To display camera images on a TV, you need a
television equipped with a video input terminal.
1.Connect one end of the AV cable that comes
with the camera to the camera’s USB/AV
connector, and the other end to the video
input terminal of the TV.
 IMPORTANT! 
• Audio volume can be adjusted only when playback is
being performed or is paused.
• If your recording has index marks (page 108) inside
it, you can jump to the index mark before or after the
current playback location by pausing playback and
then pressing [
] or []. Next, press [SET] to
resume playback from the index mark position (page
108).
To do this:
Fast forward or fast reverse
the audio
Pause and unpause audio
playback
Adjust audio volume
Toggle monitor screenindicators on and off
Cancel playback
Do this:
Hold down [
] or [].
Press [SET].
Press [] and then use []and [].
Press [] (DISP).
Press [MENU].
Yellow
(Video)White
(Audio)
AV cable
USB/AV connector Video input
terminal
TV
•Connect the yellow plug of the AV cable to the video
input (yellow) terminal of the TV, and the white plug
to the TV’s audio input (white) terminal.
Downloaded From camera-usermanual.com Casio Manuals 
						

							PLAYBACK
149
2.Turn on the TV and select its video input
mode.
3.Press [] or [] to turn on the camera, and
then perform the required operation for
playback or recording.
 IMPORTANT! 
•Make sure that “Power On” or “Power On/Off” is
selected for the camera’s power on/off functions
(page 169) when you connect to a TV to view
images.
•All icons and indicators that appear on the monitor
screen also appear on the TV screen.
•Note that the audio output is monaural.
•Depending on the size of the TV screen, recorded
images and images during recording may not fill the
entire screen.
•For video output, the audio volume level is initially
set to maximum. Perform volume level adjustment
using TV controls.
Downloaded From camera-usermanual.com Casio Manuals 
						

							PLAYBACK
150
 NOTE 
•You can connect the camera to a DVD recorder or
video deck to record images from the camera.
Simply connect the AV cable that comes with the
camera to the video input and audio input jacks of
your DVD recorder or video deck instead of to your
TV.
—After connecting, you can play a slideshow of
snapshots and movies on the camera and record
them onto a DVD or video tape. You can record
movies by selecting “
 Only” for the slideshow
“Images” setting (page 141).
—When recording images to an external device,
use [
] (DISP) to clear all indicators from the
monitor screen (page 29).
Selecting the Video Output System
You can select either NTSC or PAL for the video system to
match the system of the TV you are using.
1.In the REC mode or the PLAY mode, press
[MENU].
2.Select the “Set Up” tab, select “Video Out”,
and then press [].
3.Use [
] and [] to select the setting you
want, and then press [SET].
If you are using a TV designedfor use in this area:
U.S., Japan, and other areas
that use the NTSC system
Europe and other areas that
use the PAL systemSelect this setting:NTSC
PAL
Downloaded From camera-usermanual.com Casio Manuals