Casio Exilim Ex H20g Users Guide

							71Advanced Settings
Procedure
[r] (REC) * [MENU] * Quality Tab * Lighting
You can use this setting to optimize the balance between bright areas and dark areas 
when shooting images.
• You also can optimize the balance between bright areas and dark areas in existing 
images (page 85).
Procedure
[r] (REC) * [MENU] * Quality Tab * Color Filter
Settings: Off, B/W, Sepia, Red, Green, Blue, Yellow, Pink, and Purple
Procedure
[r] (REC) * [MENU] * Quality Tab * Sharpness
You can specify one of five sharpness settings from +2 (sharpest) to –2 (least sharp).
Procedure
[r] (REC) * [MENU] * Quality Tab * Saturation
You can specify one of five saturation settings from +2 (most saturated) to –2 (least 
saturated).
Optimizing Image Brightness (Lighting)
OnPerforms brightness correction. When this option is selected, it takes 
longer for the image to be stored after the shutter button is pressed.
OffDoes not perform brightness correction.
Using Built-in Color Filters (Color Filter)
Controlling Image Sharpness (Sharpness)
Controlling Color Saturation (Saturation)
Downloaded From camera-usermanual.com Casio Manuals 
						

							72Advanced Settings
Procedure
[r] (REC) * [MENU] * Quality Tab * Contrast
You can specify one of five contrast settings from +2 (most contrast between light and 
dark) to –2 (least contrast between light and dark).
Procedure
[r] (REC) * [MENU] * Quality Tab * Flash Intensity
You can specify one of five flash intensity settings, from –2 (weakest) to +2 
(strongest).
• Flash intensity may not change when the subject is too far away or too close.
Adjusting Image Contrast (Contrast)
Specifying Flash Intensity (Flash Intensity)
Downloaded From camera-usermanual.com Casio Manuals 
						

							73Viewing Snapshots and Movies
Viewing Snapshots and Movies
See page 30 for the procedure for viewing snapshots.
1.Press [p] (PLAY) and then use [4] and [6] to display the movie you 
want to view.
2.Press [SET] to start playback.
Movie Playback Controls
• Playback may not be possible for movies not recorded with this camera.
Viewing Snapshots
Viewing a Movie
Fast forward/
fast reverse[4] [6]
• Each press of either button increases the speed of the fast 
forward or fast reverse operation.
• To return to normal playback speed, press [SET].
Play/pause[SET]
1 frame forward/
back[4] [6]
• Holding down either button scrolls continuously.
• Image scrolling is not supported during playback in the MAP 
mode.
Volume 
adjustmentPress [2] and then press [8] [2].
• Volume can be adjusted only while movie playback is in 
progress.
Information 
display on/off[8] (DISP)
ZoomSlide the zoom controller in the direction of z ([).
• You can use [8], [2], [4], and [6] to scroll the zoomed 
image on the monitor screen. You can zoom a movie image 
up to 4.5 times normal size.
• Zooming is not supported during playback in the MAP mode.
Stop playback[MENU]
Movie icon: »
Image quality Recording time
Downloaded From camera-usermanual.com Casio Manuals 
						

							74Viewing Snapshots and Movies
1.Press [p] (PLAY), and then use [4] and [6] to display the panorama 
images you want to view.
2.Press [SET] to start playback of the panorama.
Panorama playback causes the image to scroll left, 
right, up, or down.
Playback Controls
• The following functions cannot be performed on a panorama image.
Dynamic Photo, Movie Converter, MOTION PRINT, Movie Editing, Trimming, 
Resize
Viewing a Panorama Image
To start or pause 
playback[SET]
To advance scroll while 
paused[4] [6] (When the slide direction is left or right.)
[8] [2] (When the slide direction is up or down.)
• Holding down any button scrolls continuously.
• Scrolling is not supported during MAP mode 
playback.
To hide or show display 
information[8] (DISP)
To stop playback[MENU]
Downloaded From camera-usermanual.com Casio Manuals 
						

							75Viewing Snapshots and Movies
1.In the PLAY mode, use [4] and [6] to scroll through the images until 
the one you want is displayed.
2.Slide the zoom controller towards z ([) to 
zoom.
You can use [8], [2], [4], and [6] to scroll the 
zoomed image on the monitor screen. Slide the 
zoom controller towards w to unzoom the image.
– When monitor screen contents are turned on, a 
graphic in the lower right corner of the screen 
shows what part of the zoomed image is 
currently displayed.
– To exit the zoom screen, press [MENU] or [BS].
– Though the maximum image zoom factor is 8X, 
certain image sizes may not allow zooming up 
to the full 8X.
• Pressing [SET] will lock the current zoom factor for the on-screen image. You 
can then use [4] and [6] to scroll between images, using the same zoom 
factor. Pressing [SET] again will unlock the zoom factor and allow you to use 
[8], [2], [4] and [6] to move around the currently displayed images.
1.In the PLAY mode, slide the zoom controller 
towards w (]).
Use [8], [2], [4] and [6] to move the selection 
boundary around the image menu.
To view a particular image, use [8], [2], [4], or [6] to 
move the selection boundary to the image you want 
and then press [SET].
Zooming an On-screen Image
Displaying the Image Menu
Image area
Current display areaZoom factor
Boundary
Downloaded From camera-usermanual.com Casio Manuals 
						

							76Viewing Snapshots and Movies
1.In the PLAY mode, slide the zoom controller towards w (]) twice.
This will display the calendar screen that shows the first image recorded on each 
day.
To display the first image recorded on a particular day, 
use [8], [2], [4], and [6] to move the selection 
boundary to the day you want and then press [SET].
To exit the calendar screen, press [MENU] or [BS].
• If you save an image using any one of the following 
functions, the image will appear in the calendar on the 
date that you last saved it.
Lighting, White Balance, Brightness, Resizing, Trimming, Copy, MOTION 
PRINT
If you edit the date and time of an image, the image still will appear on the date 
it was originally recorded.
1.Use the AV cable that comes with the camera to connect it to the TV.
• Make sure that you insert the cable connector into the 
USB/AV port until you feel it click securely into place. 
Failure to insert the connector fully can result in poor 
communication or malfunction.
• Note that even while the connector is fully inserted, you 
still will be able to see the metal part of the connector as shown in the 
illustration.
Displaying Images in the Calendar Screen
Viewing Snapshots and Movies on a TV Screen
YellowAV cable (bundled)
White
Making sure that the 6 mark on the camera is aligned with the 4 mark of the AV 
cable connector, connect the cable to the camera. VIDEO IN jack (yellow)AUDIO IN jacks (white)
TV
Audio Video
[USB/AV] port
Downloaded From camera-usermanual.com Casio Manuals 
						

							77Viewing Snapshots and Movies
2.Turn on the TV and select its video input mode.
If the TV has more than one video input, select the one where the camera is 
connected.
3.Press [p] (PLAY) to turn on the camera.
This will cause an image to appear on the TV screen, without anything appearing 
on the camera’s monitor screen.
• Pressing [ON/OFF] (Power) or [r] (REC) will not turn on the camera while the 
AV cable is connected.
• You also can change the aspect ratio of the screen and the video output 
system (page 150).
4.Now you can display images and play back movies as you normally do.
IMPORTANT!
• Before connecting to a TV to display images, be sure to configure the camera’s 
[r] (REC) and [p] (PLAY) buttons for “Power On” or “Power On/Off” (page 148).
• Audio is initially output by the camera at maximum volume. When you first start 
displaying images, set the TV volume control at a relatively low level and then 
adjust it as required.
NOTE
• Audio is monaural.
• Certain TVs may cut off part of the images.
• All icons and indicators that appear on the monitor screen also appear on the TV 
screen. You can use [8] (DISP) to change the display contents.
Downloaded From camera-usermanual.com Casio Manuals 
						

							78Viewing Snapshots and Movies
Use a commercially available HDMI cable to 
connect the camera to the TV. For 
information about playback, see page 76.
• Use a commercially available HDMI cable 
that is marked with the logo shown to the 
right.
IMPORTANT!
• Output to a TV is not supported in the REC mode.
NOTE
• Use a HDMI cable that with a plug that is compatible with the camera’s HDMI mini 
connector on one end, and a plug that is compatible with your TV’s HDMI 
connector on the other end.
• Proper image and/or audio output and other operations may not be possible with 
some devices.
• Connecting the camera to the HDMI connector of another device can damage both 
the camera and the other device. Never connect two HDMI output connectors to 
each other.
• Make sure that the camera is turned off before plugging in or unplugging the cable. 
Check the user documentation that comes with the TV for information about 
requirements before plugging into or unplugging from the TV.
• When cables are connected to both the USB/AV port and the HDMI output 
connector, the HDMI output connector connection is given priority.
• Disconnect the HDMI cable when you are not using HDMI output. The camera’s 
monitor screen may not operate normally while the HDMI cable is connected.
• Audio is monaural.
• Some TVs may not be able to output images and/or audio correctly.
• Audio is initially output by the camera at maximum volume. When you first start 
displaying images, set the TV volume control at a relatively low level and then 
adjust it as required.
Viewing High-quality Movies on a Hi-Vision Television
HDMI connectorHDMI cable (commercially available)
HDMI mini connector HDMI inputHDMI output 
(Mini)
Terminal 
cover
Downloaded From camera-usermanual.com Casio Manuals 
						

							79Viewing Snapshots and Movies
.Selecting the HDMI Terminal Output Method (HDMI Output)
Procedure
[MENU] * Set Up Tab * HDMI Output
Use this setting to select the digital signal format when connecting to a TV with an 
HDMI cable.
*1080i corresponds to 1080 60i, but not 1080 50i. Because of this, the required output 
method may be 576p when outputting to a digital TV in a PAL reception area that does 
not support 1080i 60i. If you are in a PAL reception area and nothing is displayed 
automatically, change the setting to 576p.
• If an image does not appear when “Auto” is selected as the output method, try 
changing this setting to something else.
Recording Camera Images to a DVD Recorder or Video Deck
Use one of the following methods to connect the camera to the recording device 
using the camera’s bundled AV cable.
– DVD recorder or video deck: Connect to the VIDEO IN and AUDIO IN terminals.
– Camera: USB/AV port
You can play a slideshow of snapshots and movies on the camera and record it on a 
DVD or video tape. You can record movies by selecting “» Only” for the slideshow 
“Images” setting (page 80). When recording images to an external device, use [8] 
(DISP) to clear all indicators from the monitor screen (page 152).
For information about connecting a monitor to the recording device and about how to 
record, see the user documentation that comes with the recording device you are 
using.
AutoThis setting will cause the format to change automatically in accordance 
with the connected TV. Normally, you should use this mode.
1080i1080i format output*
480p480p format output
576p576p format output
Downloaded From camera-usermanual.com Casio Manuals 
						

							80Other Playback Functions (PLAY)
Other Playback Functions (PLAY)
This section explains menu items that you can use to configure settings and perform 
other playback operations.
Procedure
[p] (PLAY) * [MENU] * PLAY Tab * Slideshow
For information about menu operations, see page 58.
Playing a Slideshow on the Camera (Slideshow)
Start
Starts the slideshow.
Images
Specifies the type of images to be included in the slideshow
All images: Snapshots and movies
T Only: Snapshots only
» Only: Movies only
Date Setting: Images from specific dates
• Perform the following steps to specify a date.
1Use [8], [2], [4], and [6] to move the red selection boundary the date 
you want to select, and then press [SET].
This will select the check box of date you selected.
2Repeat step 1 to select all of the dates whose images you want include in 
the slideshow.
3After selecting all of the images you want, press [BS].
• If you save an image using any one of the following functions, the image will 
appear in the calendar on the date that you saved. 
Lighting, White Balance, Brightness, Resize, Trimming, Copy, MOTION 
PRINT
• If you edit the date and/or time of an image, the image still will appear on the 
date it was originally recorded.
• You can select up to 15 images for a slideshow.
• All currently selected slideshow images are deselected whenever you turn off 
the camera.
Time
Time from the start to the end of the slideshow
1 to 5 minutes, 10 minutes, 15 minutes, 30 minutes, 60 minutes
Downloaded From camera-usermanual.com Casio Manuals