Casio EX S500 User Manual

							141
PLAYBACK
 IMPORTANT! 
• Take care that you do
not block the
microphone with your
fingers.
• Good recording results
are not possible when
the camera is too far
from the subject.
• The 
 (Audio) icon appears on the monitor screen
after audio recording is complete.
• You will not be able to record audio when remaining
memory capacity is low.
• You cannot add audio to the following types of
images.
— Movie images
— Images created with MOTION PRINT
— Protected snapshot (page 148)
• Audio that is re-recorded or deleted cannot be
recovered. Make sure you no longer need audio
before re-recording or deleting it.
Microphone
Playing Back a Voice Recording File
Perform the following steps to play back a voice recording
file.
1.In the PLAY mode, use [] and [
] to display
the voice recording file (a file with 
 on it)
you want to play.
2.Press [SET].
• This starts playback of
the voice recording file
through the camera’s
speaker.
• You can perform the
following operations
while audio is playing. 
						

							142
PLAYBACK
 IMPORTANT! 
• Audio volume can be adjusted only when playback is
being performed or is paused.
• If your recording has index marks (page 104) inside
it, you can jump to the index mark before or after the
current playback location by pausing playback and
then pressing [] or [
]. Next, press [SET] to
resume playback from the index mark position.
To do this:
Fast forward or fast reverse
the audio
Pause and unpause audio
playback
Adjust audio volume
Toggle monitor screenindicators on and off
Cancel playback
Do this:
Hold down [] or [
].
Press [SET].
Press [] and then use []and [].
Press [] (DISP).
Press [MENU].
Displaying Camera Images on a TV Screen
You can display recorded images on a TV screen. To
display camera images on a TV, you need a television
equipped with a video input terminal, USB cradle, and the
AV cable that comes with the camera.
1.Connect one end of the AV cable that comes
with the camera to the [AV OUT] port of the
USB cradle, and the other end to the video
input terminal of the TV.
• Connect the yellow plug of the AV cable to the video
input (yellow) terminal of the TV, and the white plug
to the TV’s audio input (white) terminal. 
						

							143
PLAYBACK
AV cable
[AV OUT] (AV output port)
Video input terminal
TV
2.Turn off the camera.
3.Set the camera onto the USB cradle.
4.Turn on the TV and select its video input
mode.
5.Press [] to turn on the camera, and then
perform the required operation for playback.
 IMPORTANT! 
• Make sure that “Power On” or “Power On/Off” is
selected for the camera’s power on/off functions
(page 161) when you connect to a TV to view
images.
• All icons and indicators that appear on the monitor
screen also appear on the TV screen.
• Note that the audio output is monaural.
• The camera’s monitor screen will go blank during
video output.
• Pressing the USB cradle’s [PHOTO] button will
activate the Photo Stand feature (page 136) and
display images on the TV screen.
• Depending on the size of the TV screen, recorded
images may not fill the entire screen.
• For video output, the audio volume level is initially
set to maximum. Perform volume level adjustment
using TV controls.
• After using an optionally available AV cable (EMC-
2A) to connect the camera’s USB cradle connector
directly to the AUDIO IN terminal of a TV, you can
view recorded images on the TV and even use the
TV screen to compose images before recording
them.
B 
						

							144
PLAYBACK
Selecting the Video Output System
You can select either NTSC or PAL for the video system to
match the system of the TV you are using.
1.In the REC mode or the PLAY mode, press
[MENU].
2.Select the “Set Up” tab, select “Video Out”,
and then press [
].
3.Use [] and [] to select the setting you
want, and then press [SET].
If you are using a TV designedfor use in this area:
U.S., Japan, and other areas
that use the NTSC system
Europe and other areas that
use the PAL systemSelect this setting:NTSC
PAL
 IMPORTANT! 
• Images will not display properly if you select the
wrong video system.
• This camera supports the NTSC and PAL video
systems only. Images will not display properly if you
use a TV (monitor) that is designed for a different
video system.
B 
						

							DELETING FILES
145
DELETING FILES
You can delete a single file, or you can delete all files
currently in memory.
 IMPORTANT! 
•Note that file deletion cannot be undone. Once you
delete a file, it is gone. Make sure you really do not
need a file anymore before you delete it. Especially
when deleting all files, make sure you check all the
files you have stored before proceeding.
•A protected file cannot be deleted. To delete a
protected file, unprotect it first (page 148).
•Delete cannot be performed when all files in memory
are protected (page 149).
•Deleting an audio snapshot deletes both the image
file and the audio file attached to it.
•You cannot use the procedures in this section to
delete images from the FAVORITE folder. See the
procedures on page 152 for details about deleting
FAVORITE folder contents.
Deleting a Single File
1.In the PLAY mode,
press [] (
 ).
2.Use [
] and [] to scroll through files and
display the one you want to delete.
3.Use [] and [] to select “Delete”.
•To exit the file delete operation without deleting
anything, select “Cancel”.
4.Press [SET] to delete the file.
•Repeat steps 2 through 4 to delete other files, if you
want.
5.Press [MENU] to exit the menu screen. 
						

							DELETING FILES
146
Deleting All Files
1.In the PLAY mode, press [] ( ).
2.Use [] and [] to select “All Files Delete”,
and then press [SET].
3.Use [] and [] to select “Yes”.
•To exit the file delete operation without deleting
anything, select “No”.
4.Press [SET] to delete all the files.
•The message “There are no files.” appears on the
screen after all of the files are deleted. 
						

							FILE MANAGEMENT
147
FILE MANAGEMENT
The file management capabilities of the camera make it
easy to keep track of images. You can protect files against
deletion and store the files you want in the camera’s built-in
memory.
Folders
Your camera automatically creates folders in its built-in
memory or on the memory card.
Memory Folders and Files
An image you record is automatically stored in a folder,
whose name is a serial number. You can have up to 900
folders in memory at the same time. Folder names are
generated as shown below.
Example: Name of the 100th folder.Each folder can hold files numbered up to 9,999.
Trying to store the 10,000th file in a folder causes the next
serially numbered folder to be created. File names are
generated as shown below.
Example: Name of the 26th file
Extension
CIMG0026.JPG
Serial number (4 digits)
• The folder and file names described here appear when
you view folders and files on a computer. See page 28 for
information about how the camera displays folder and file
names.
• The actual number of files you will be able to store on a
memory card depends on image size and quality, card
capacity, etc.
• For details about the folder structure, see “Memory Folder
Structure” on page 195.
100CASIO
Serial number (3 digits)
B 
						

							FILE MANAGEMENT
148
4.Use [] and [] to
select “On”, and then
press [SET].
•A file that is protected is
indicated by the 
mark.
•To unprotect a file, select
“Off” in step 4, and then
press [SET].
5.Press [MENU] to exit the menu screen.
Protecting Files
Once you protect a file it cannot be deleted (page 145).
You can protect files individually or you can protect all files
in memory with a single operation.
 IMPORTANT! 
•Even if a file is protected, it still will be deleted by a
memory card format operation (page 166) or a built-
in memory format operation (page 162).
To protect a single file
1.In the PLAY mode, press [MENU].
2.Select the “PLAY” tab,
select “Protect”, and
then press [].
3.Use [
] and [] to scroll through files and
display the one you want to protect.
B 
						

							FILE MANAGEMENT
149
To protect all files in memory
1.In the PLAY mode, press [MENU].
2.Select the “PLAY” tab, select “Protect”, and
then press [].
3.Use [] and [] to select “All Files : On”, and
then press [SET].
•To unprotect all files, press [SET] in step 3 so the
setting shows “All Files : Off”.
4.Press [MENU] to exit the menu screen.
Using the FAVORITE Folder
You can copy scenery shots, photos of your family, or other
special images from a file storage folder (page 195) to the
FAVORITE folder in built-in memory (page 195). Images in
the FAVORITE folder are not displayed during normal
playback, so it helps to keep your personal images private
as you carry them around. FAVORITE folder images are
not deleted when you change memory cards, so you can
always keep them on hand.
To copy a file to the FAVORITE folder
1.In the PLAY mode, press [MENU].
2.Select the “PLAY” tab,
select “Favorites”, and
then press []. 
						

							FILE MANAGEMENT
150
3.Use [] and [] to
select “Save”, and
then press [SET].
•This displays the names
of the files in built-in
memory or on the loaded
memory card.
4.Use [
] and [] to select the file you want to
copy to the FAVORITE folder.
5.Use [] and [] to select “Save”, and then
press [SET].
•This copies the displayed file to the FAVORITE
folder.
6.After copying all of the files you want, use []
and [] to select “Cancel”, and then press
[SET] to exit.
 NOTE 
•Copying an image file with the above procedure
creates a 320 × 
240-pixel QVGA-size image in the
FAVORITE folder.
•A file copied into the FAVORITE folder is
automatically assigned a file name that is a serial
number. Though the serial number starts from 0001
and can go as high as 9999, the actual upper end of
the range depends on built-in memory capacity.
Remember that the maximum number of images that
can be stored in built-in memory depends on the size
of each image and other factors.
 IMPORTANT! 
•Note that an image that has been copied to the
FAVORITE folder and then resized cannot be
returned to its original size.
•Files in the FAVORITE folder cannot be copied to a
memory card.