Casio EX S5 User Manual

							81Printing
Printing
• You can specify which images you want to print, the number of copies, and date 
stamp settings before printing (page 84).
Printing Snapshots
Professional Print Service
You can take a memory card that contains the images you 
want to print to a professional print service and have them 
printed.
Printing on a Home Printer
Printing Images on a Printer with Memory Card Slot
You can use a printer equipped with a memory card slot to print 
images directly from a memory card. For details, see the user 
documentation that comes with your printer.
Connecting Directly to a PictBridge Compatible 
Printer
You can print on a printer that supports PictBridge (page 
82).
Printing with a Computer
After transferring the images to your computer, use 
commercially available software to print. 
						

							82Printing
You can connect the camera directly to a printer that supports PictBridge and print 
images without going through a computer.
.To set up the camera before connecting to a printer
1.Turn on the camera and press [MENU].
2.On the “Set Up” tab, select “USB” and then press [6].
3.Use [8] and [2] to select “PTP (PictBridge)”, and then press [SET].
.Connecting the Camera to a Printer
Use the USB cable that 
comes bundled with the 
camera to connect the 
camera to your printer’s USB 
port.
• The camera does not draw 
power over the USB cable. 
Make sure the camera’s 
battery is sufficiently 
charged before 
connecting.
• Make sure that you insert 
the cable connector into 
the USB/AV port until you 
feel it click securely into 
place. Failure to insert the 
connector fully can result 
in poor communication or 
malfunction.
• Note that even while the 
connector is fully inserted, you still will be able to see the 
metal part of the connector as shown in the illustration.
• When connecting the USB cable to a USB port, make sure 
you align the connector correctly with the port.
Connecting Directly to a PictBridge Compatible Printer
USB
USB cable
USB port
USB/AV port
Making sure that the 2 mark on the camera is 
aligned with the 8 mark of the USB cable connector, 
connect the cable to the camera.Large connector
Small connector 
						

							83Printing
.To print
1.Turn on the printer and load paper.
2.Turn on the camera.
This will display the print menu screen.
3.Use [8] and [2] to select “Paper Size”, and 
then press [6].
4.Use [8] and [2] to select a paper size and 
then press [SET].
• The following are the available paper sizes.
3.5x5, 5x7, 4x6, A4, 8.5x11, By Printer
• Selecting “By Printer” prints using a paper size selected on the printer.
• See the documentation that comes with your printer for information about 
paper settings.
5.Use [8] and [2] to specify the print option you want.
• To toggle date stamping on and off, press [BS]. 
The date stamp will be printed when “On” is 
indicated on the monitor screen.
6.Use [8] and [2] to select “Print” and then 
press [SET].
Printing will start and the message “Busy... Please 
wait...” will appear on the monitor screen. The message will disappear after a 
short while, even though printing is still being performed. Pressing any camera 
button will cause the printing status to re-appear. The print menu screen will re-
appear when printing is complete.
• If you selected “1 Image”, you can repeat the procedure from step 5, if you 
want.
7.After printing is complete, turn off the camera and disconnect the USB 
cable from the printer and camera.
1 Image : Prints one image. Select and then press [SET]. Next, use [4] and 
[6] to select the image you want to print.
DPOF Printing : Prints multiple images. Select and then press [SET]. With this 
option, images will be printed in accordance with DPOF settings 
(page 84). 
						

							84Printing
.Digital Print Order Format (DPOF)
DPOF is a standard that allows you to include image type, number of copy, 
and time stamp on/off information on the memory card with the images. 
After configuring settings, you can use the memory card to print on a home 
printer that supports DPOF or take the memory card to a professional print 
service.
• Whether or not you will be able to use DPOF settings for printing depends on the 
printer you are using.
• Some professional print services may not support DPOF.
.Configuring DPOF Settings Individually for Each Image
Procedure
[p] (PLAY) * Snapshot Screen * [MENU] * PLAY Tab * 
DPOF Printing * Select images
1.Use [4] and [6] to scroll through the files until the image you want to 
print is displayed.
2.Use [8] and [2] to specify the number of copies.
You can specify a value up to 99. Specify 00 if you do not want to print the image.
• If you want to include the date in the images, press [BS] so “On” is shown for 
date stamping.
• Repeat steps 1 and 2 to configure settings for other images, if you want.
3.Press [SET].
Using DPOF to Specify Images to be Printed and the Number 
of Copies 
						

							85Printing
.Configuring the Same DPOF Settings for All the Images
Procedure
[p] (PLAY) * Snapshot Screen * [MENU] * PLAY Tab * 
DPOF Printing * All images
1.Use [8] and [2] to specify the number of copies.
You can specify a value up to 99. Specify 00 if you do not want to print the image.
• If you want to include the date in the images, press [BS] so “On” is shown for 
date stamping.
2.Press [SET].
DPOF settings are not cleared automatically after printing is complete.
The next DPOF print operation you execute will be performed using the last DPOF 
settings you configured for the images. To clear DPOF settings, specify “00” for the 
number of copies of all images.
Tell your print service about your DPOF settings!
If you take a memory card to a professional print service, be sure to tell them that it 
includes DPOF settings for the images to be printed and the number of copies. If you 
don’t, the print service may print all the images without regard to your DPOF settings, 
or they may ignore your date stamp setting. 
						

							86Printing
.Date Stamping
You can use one of the following three methods to include the recording date in the 
printout of an image.
.Standards Supported by the Camera
• PictBridge
This is a standard of the Camera and Imaging Products Association 
(CIPA). You can connect the camera directly to a printer that supports
PictBridge, and perform image selection and printing using the 
camera monitor screen and controls.
•Exif Print
Printing on a printer that supports Exif Print (Exif 2.2) uses 
information about shooting conditions recorded with the image to 
enhance printed image quality. Contact your printer manufacturer 
for information about models that support Exif Print, printer upgrades, etc.
Configuring 
camera settingsConfigure DPOF settings (page 84).
You can turn date stamping on and off each time you print. 
You can configure settings so some images include the date 
stamp and some don’t.
Configure the Camera’s Time Stamp setting (page 112).
• The camera’s Time Stamp setting imprints the date into a 
snapshot when you shoot it, so the date is always included 
when you print. It cannot be deleted.
• Do not turn on DPOF date stamping for an image that 
includes a date stamped with the camera’s Time Stamp 
function. Doing so can cause the two stamps to be 
overprinted.
Configuring 
computer settingsYou can use commercially available image management 
software to date stamp images.
Professional print 
serviceRequest date stamping when ordering prints from a 
professional print service. 
						

							87Using the Camera with a Computer
Using the Camera with a Computer
You can perform the operations described below while the camera is connected to a 
computer.
*Windows only
The procedures you need to perform when using the camera with your computer and 
when using the bundled software are different for Windows and the Macintosh.
Things you can do using a computer...
Save images to a 
computer and 
view them there• Save images and view them manually (USB 
connection) (pages 89, 98).
• Transfer images to a computer 
automatically over a wireless LAN for 
viewing (Eye-Fi) (page 103).
Transfer images 
stored on your 
computer to 
camera memory In addition to images, you also can transfer 
screen shot images from your computer to the 
camera (Photo Transport*) (page 95).
Playback and 
edit movies• You can play back movies (pages 93, 101).
• To edit movies, use commercially available 
software as required.
• Windows users should refer to “Using the Camera with a Windows Computer” 
on page 88.
• Macintosh users should refer to “Using the Camera with a Macintosh” on page 
98. 
						

							88Using the Camera with a Computer
Install the required software in accordance with the version of Windows you are 
running and what you want to do.
*YouTube Uploader for CASIO and Photo Transport will not run under 64-bit versions of 
Windows Vista.
Using the Camera with a Windows Computer
When you want 
to do this:Operating System 
VersionInstall this software:See 
page:
Save images to a 
computer and 
view them there 
manuallyVista / XP / 2000 Installation not required. 89
Play movies Vista / XP / 2000Installation not required.
• Windows Media Player, 
which is already installed on 
most computers, can be used 
for playback.
• If your computer is running 
Windows 2000 and does not 
have DirectX9.0c or higher 
installed, download DirectX 
from the Microsoft DirectX 
site and install it on your 
computer.93
Edit movies Vista / XP / 2000–
• Use commercial software as 
required.–
Upload movie 
files to YouTubeVista / XP (SP2/SP3) /
2000 (SP4)YouTube Uploader for 
CASIO*93
Transfer images 
to the cameraVista / XP / 2000Photo Transport 1.0*95
View the User’s 
GuideVista / XP (SP2/SP3) /
2000 (SP4)Adobe Reader 8
(Not required if already 
installed.)97
B 
						

							89Using the Camera with a Computer
.Computer System Requirements for Bundled Software
Computer system requirements are different for each of the applications. See the 
“Read me” file that comes with each application for details. Information about 
computer system requirements also can be found under “Computer System 
Requirements for Bundled Software” on page 132 of this manual.
.Precautions for Windows Users
• Except for Adobe Reader, the bundled software requires Administrator privileges to 
run.
• Operation on a self-made computer is not supported.
• Operation may not be possible under certain computer environments.
You can connect the camera to your computer in order to view and store images 
(snapshot and movie files).
.To connect the camera to your computer and save files
1.Turn on the camera and press [MENU].
2.On the “Set Up” tab, select “USB” and then press [6].
3.Use [8] and [2] to select “Mass Storage”, and then press [SET].
Viewing and Storing Images on a Computer 
						

							90Using the Camera with a Computer
4.Turn off the camera and 
then use the USB cable that 
comes with the camera to 
connect it to your 
computer.
• The camera does not draw 
power over the USB cable. 
Make sure the camera’s 
battery is sufficiently charged 
before connecting.
• Make sure that you insert the 
cable connector into the 
USB/AV port until you feel it 
click securely into place. 
Failure to insert the 
connector fully can result in 
poor communication or 
malfunction.
• Note that even while the 
connector is fully inserted, you still will be able to see 
the metal part of the connector as shown in the 
illustration.
• When connecting the USB cable to a USB port, make 
sure you align the connector correctly with the port.
• Your computer may not be able to recognize the camera if you connect via a 
USB hub. Always connect directly to the computer’s USB port.
5.Turn on the camera.
USB port
USB cable
Making sure that the 2 mark on the camera is 
aligned with the 8 mark of the USB cable 
connector, connect the cable to the camera.USB/AV port Large connector
Small connector