Casio EX FH20 User Manual

71Using BEST SHOT
You can use these features to shoot an image automatically whenever the subject 
moves into or moves out of a frame on the monitor screen. You also can configure the 
camera to record images of what happened immediately before and after the subject 
moves.
.To setup the camera
1.Set the mode dial to t (Single Shot), × (High-speed CS), or ª (Flash 
CS).
2.Press [BS].
3.Select “Move Out CS” or “Move In CS”.
4.Press [SET].
5.Configure the boundary location and size 
settings.
6.Press...

72Using BEST SHOT
8.Use [4] and [6] to select the subject movement sensitivity, and then 
press [SET].
• You can select any one of three sensitivity levels: “High”, “Normal”, or “Low”.
• Move Out CS Setting Guide
• Move In CS Setting Guide
9.Use [8] and [2] to select the second control panel option from the 
bottom (High-speed CS fps).
10.Use [4] and [6] to select the CS speed setting 
you want, and then press [SET].
• You select a value in the range of 1 frame per 
second to 40 frames per second for the...

73Using BEST SHOT
.To shoot using Move Out CS
1.Compose the image so the subject is within the boundary on the 
monitor screen.
2.Half-press the shutter button.
• The camera will adjust exposure and focus automatically.
3.When the boundary on the monitor screen turns 
green, press the shutter button the rest of the 
way down.
At this time the camera will go into recording standby 
and start pre-recording images and storing them in a 
buffer, in accordance with the Prerecord Time setting 
you configured...

74Using BEST SHOT
.To shoot using Move In CS
1.Compose the image at a location where you expect the subject to enter 
the boundary on the monitor screen.
2.Half-press the shutter button.
• The camera will adjust exposure and focus automatically.
• In this case, use of manual focus (page 46) to preset a fixed focus is 
recommended.
3.When the boundary on the monitor screen turns 
green, press the shutter button the rest of the 
way down.
At this time the camera will go into recording standby 
and start...

75Using BEST SHOT
NOTE
• Compose the image so the entire subject and its background are within the 
boundary. Recording may not be performed correctly if there is little difference 
between the subject and the part of the background enclosed by the boundary. 
Also, Move Out CS may not record correctly if the subject is not in the center of the 
boundary.
• Move In CS and Move Out CS do not operate correctly if you press the shutter 
button all the way down. Be sure to half-press the shutter button. After...

76Advanced Settings
Advanced Settings
The following are menu operations you can use to configure various camera settings.
.Example Menu Screen Operation
Press [MENU] to display the menu screen.
• Menu contents are different in the REC mode and PLAY mode.
Menu Screen Operation Buttons
1.In the REC mode, press [MENU].
This will display the menu screen.
2.Use [4] and [6] to select the tab where the item you want to configure 
is located.
Using On-screen Menus
[4] [6]Selects tabs. [6] is also used to display...

77Advanced Settings
3.Use [8] and [2] to select the menu item you 
want, and then press [6].
4.Use [8] and [2] to change the setting.
5.After the setting is the way you want, press 
[SET].
• Pressing [4] registers the selected setting and 
returns to the menu.
• To configure settings on another tab after 
pressing [
4] to return to the menu, use [8] to 
move the highlighting up to the tabs, and then 
use [
4] and [6] to select the tab you want.
.Menu Operations in This Manual
Menu operations are...

78Advanced Settings
Procedure
[r] (REC) *[MENU] * REC Tab * Self-timer
With the Self-timer, pressing the shutter button starts a timer. The shutter is released 
and the image is shot after a fixed amount of time.
• The front lamp flashes while the Self-timer countdown is 
in progress.
• You can interrupt an ongoing Self-timer countdown by 
pressing [SET].
NOTE
• The Self-timer cannot be used together with the following features.
High-speed CS with Prerecord (Still image), movie recording with Prerecord...

79Advanced Settings
Procedure
[r] (REC) * [MENU] * REC Tab * AF Assist Light
Half-pressing the shutter button while this setting is 
selected causes the front lamp to light, which provides 
illumination for focusing in areas where lighting is dim. 
Leaving this function turned off is recommended when 
shoot portraits from short distances, etc.
IMPORTANT!
• Never look directly into the front lamp while it is lit.
• Make sure your finger is not covering the front lamp.
Procedure
[r] (REC) * [MENU] * REC...

80Advanced Settings
NOTE
•Only “A
 Camera AS” can be used during movie recording.
• The ISO sensitivity setting (page 38) must be “AUTO” for “S Image AS” to work.
• If the flash fires, the Anti Shake icon will remain on the display, even though Anti 
Shake does not function during flash photography.
• Shooting with Anti Shake can cause an image to appear somewhat coarser than 
normal and can cause slight deterioration of image resolution.
• Anti Shake may not be able to eliminate the effects of camera or...