Casio EX FC200S User Manual

41Snapshot Tutorial
ISO sensitivity is a measure of sensitivity to light.
1.In the REC mode, press [SET].
2.Use [8] and [2] to select the second control panel option from the top 
(ISO Sensitivity).
3.Use [4] and [6] to select the setting you want and then press [SET].
• While “AUTO” is selected, Anti Shake corrects for subject movement only 
(page 91).
• Higher ISO sensitivity values tend to result in digital noise in images.
• Since higher ISO sensitivity values tend to result in digital noise in...

42Snapshot Tutorial
You can adjust white balance to match the source of light available where you are 
shooting and avoid the blue cast that results when shooting outdoors when it is 
cloudy, and the green cast that results when shooting under fluorescent lighting.
1.In the REC mode, press [SET].
2.Use [8] and [2] to select the third control panel option from the top 
(White Balance).
3.Use [4] and [6] to select the shooting condition you want and then 
press [SET].
• When “‡ Auto WB” is selected for the...

43Snapshot Tutorial
You can manually adjust an image’s exposure value (EV value) before shooting it.
• Exposure Compensation Range: –2.0 EV to +2.0 EV
• Unit: 1/3EV
1.In the REC mode, press [SET].
2.Use [8] and [2] to select the fourth control panel option from the top 
(EV Shift).
3.Use [4] and [6] to adjust the exposure compensation value.
To cancel exposure compensation, change 
the EV value to 0.0.
4.Press [SET].
This applies the exposure compensation value. The exposure compensation 
value you set...

44Snapshot Tutorial
1.In the REC mode, press [2] ( ) 
once.
2.Use [4] and [6] to select the flash 
setting you want and then press 
[SET].
3.Press the shutter button to shoot.
• For information about Flash Range, see page 192.
Using Flash (Flash)
 Auto FlashFlash fires automatically in accordance with exposure 
(amount of light and brightness) conditions.
 Flash OffFlash does not fire.
 Flash OnFlash always fires. This setting can be used to brighten a 
subject that normally comes out dark due to...

45Snapshot Tutorial
NOTE
• Take care so your fingers and the strap do not block the flash.
• The desired effect may not be obtained when the subject is too far away or too 
close.
• Flash charging time (page 192) depends on operating conditions (battery 
condition, ambient temperature, etc.).
• Shooting with flash turned off when lighting is dim results in a slow shutter speed, 
which can cause image blur due to camera movement. Under such conditions, 
secure the camera with a tripod, etc.
• With red eye...

46Snapshot Tutorial
Your camera is equipped with various types of zoom: optical zoom, HD Zoom, Single 
SR Zoom, Multi SR Zoom, and digital zoom. The maximum zoom factor depends on 
the image size setting and the digital zoom on/off settings.
1.In the REC mode, slide the zoom controller to zoom.
2.Press the shutter button to shoot the image.
NOTE
• Use of a tripod is recommended to protect against image blur due to camera 
movement when shooting with telephoto.
• Performing a zoom operation changes the...

47Snapshot Tutorial
During a zoom operation, a zoom bar appears on the monitor screen to show the 
current zoom setting.
Interpreting the Zoom Bar
Range where image deterioration is suppressed. 
(optical zoom, HD Zoom, 
Single SR Zoom, Multi SR Zoom)
1X
28.0X to 111.6X
Zoom pointer 
(Indicates current zoom.)
Point from which image deteriorates
• The location of this point depends on the image size, the “Zoom (SR)” 
setting, and whether Multi SR Zoom is enabled.
Zoom (SR) SettingPoint from which image...

48Snapshot Tutorial
.Zoom Icon
The appearance of the zoom icon on the monitor screen depends on the zoom factor.
.Zoom Factor
The digital zoom factor depends on the image size (page 38), the super resolution 
zoom setting, and on whether or not the “Multi SR Zoom” BEST SHOT scene is 
selected (page 76).
Multi SR Zoom is enabled by selecting the “Multi SR Zoom” BEST SHOT scene.
Optical zoomNot displayed
HD ZoomNot displayed
Single SR Zoomç (White)
Multi SR Zoom (Orange)
Digital zoomê
Image 
size
Maximum...

49Snapshot Tutorial
There are two types of Super Resolution Zoom: Single SR Zoom and Multi SR Zoom. 
Single SR Zoom uses super resolution to expand the zoom range in which image 
quality deterioration is minimized. Multi SR Zoom shoots a series of High Speed CS 
images, which are then combined into final image to suppress image quality 
deterioration across a range that is greater than Single SR Zoom. For information 
about the effective zoom factor ranges in which Super Resolution Zoom is effective,...

50Snapshot Tutorial
To shoot with Continuous Shutter, press [BS] (BEST 
SHOT) and then select the “High Speed CS” scene.
NOTE
• To return from the “High Speed CS” HS BEST 
SHOT scene to the Single Shot mode, press 
[AUTO].
With High Speed CS, you can configure the camera to shoot at a speed of 3, 5, 10, 
15, or 30 images per second, as long as you keep the shutter button and there is 
memory available to store the images. With Prerecord CS, half-pressing the shutter 
button starts continual pre-recording...