Casio EX FC100 User Manual

							111Other Playback Functions (PLAY)
Procedure
[p] (PLAY) * Movie Screen * [MENU] * PLAY Tab * 
MOTION PRINT
1.Use [4] and [6] to scroll 
through the movie frames 
and display the one you 
want to use as the image 
of the MOTION PRINT 
image.
Holding down [4] or [6] 
scrolls at high speed.
2.Use [8] and [2] to select either “9 frames” or “1 frame” and then 
press [SET].
• When “9 frames” is selected, the frame you select in step 1 will be in the center 
of the MOTION PRINT image.
• Only the frames of movies recorded on this camera can be used in a MOTION 
PRINT image.
Creating a Snapshot of Movie Frames (MOTION PRINT)
9 frames 1 frame 
						

							112Other Playback Functions (PLAY)
Procedure
[p] (PLAY) * Movie Screen of Movie to be Edited * [MENU] * 
PLAY Tab * Movie Editing
The Movie Editing feature lets you use one of the following procedures to edit out a 
specific part of a movie.
1.Use [8] and [2] to select the editing method you want to use and then 
press [SET].
2.Use the following operations to select the frame 
(point) from which or to which you want to cut 
the movie (the cut point).
Editing a Movie on the Camera (Movie Editing)
 Cut
(To-Point Cut)Cuts everything from the beginning of the movie up to the 
current location.
 Cut
(Point-To-Point Cut)Cuts everything between two points.
 Cut
(From-Point Cut)Cuts everything from the current location to the end of the 
movie.
[4] [6]During playback, changes the playback 
direction and playback speed. While 
playback is paused, scrolls forward or back.
[SET]Toggles between pause and play. 
}
~
¡
Cut range (yellow) 
						

							113Other Playback Functions (PLAY)
3.Press [2] to display the editing menu and specify one or two cut 
points.
4.Use [8] and [2] to select “Yes” and then press [SET].
The selected cut operation will take considerable time to complete. Don’t try to 
perform any camera operation until the “Busy... Please wait...” message 
disappears from the monitor screen. Note that a cut operation can take a long 
time if the movie being edited is long.
IMPORTANT!
• When you edit a movie, only the result is saved. The original movie is not retained. 
An editing operation cannot be undone.
NOTE
• A movie that is shorter than five seconds cannot be edited.
• Editing of movies recorded with a different type of camera is not supported.
• You will not be able to edit a movie if the amount of remaining memory capacity is 
less than the size of the movie file you want to edit. If there is not enough memory 
available, delete files you no longer need to free up more.
• Splitting of a movie into two movies and splicing of two different movies into a 
single movie are not supported.
• You also can start a movie editing operation while the movie you want to edit is 
playing back. When playback reaches a frame where you want a cut point to be, 
press [SET] to pause playback. Next, press [2] to display the menu of editing 
options. Perform editing using the same procedures as described above.
 Cut
(To-Point Cut)While the frame you want the cut to be up to is 
displayed, press [2].
 Cut
(Point-To-Point Cut)
1While the frame you want the first (From) cut to be is 
displayed, press [2].
2Select another frame.
3While the frame you want the second (To) cut to be 
is displayed, press [2].
 Cut
(From-Point Cut)While the frame you want the cut to be from is 
displayed, press [2].
}
~
¡ 
						

							114Other Playback Functions (PLAY)
Procedure
[p] (PLAY) * Snapshot Screen * [MENU] * PLAY Tab * 
White Balance
You can use the white balance setting to select a light source type for a recorded 
image, which will affect the colors of the image.
NOTE
• You also can adjust the white balance when recording images (page 38).
• The original snapshot is retained in memory and not deleted.
• When you display an altered image on the camera’s monitor screen, the date and 
time indicates when the image was originally recorded, not when the image was 
altered.
Adjusting White Balance (White Balance)
 DaylightOutdoors, fair weather
 OvercastOutdoors, cloudy to rain, in tree shade, etc.
 ShadeVery high temperature light, such as building shade, etc.
 Day White 
FluorescentWhite or day white fluorescent lighting, without suppressing 
color cast
 Daylight 
FluorescentDaylight fluorescent lighting, while suppressing color cast
 TungstenSuppressing of the appearance of light bulb lighting
CancelNo white balance adjustment
¤
'
“
†
–
«
B 
						

							115Other Playback Functions (PLAY)
Procedure
[p] (PLAY) * Snapshot Screen * [MENU] * PLAY Tab * 
Brightness
You can select one of five brightness levels, from +2 (brightest) to –2 (least bright).
NOTE
• The original snapshot is retained in memory and not deleted.
• When you display an altered image on the camera’s monitor screen, the date and 
time indicates when the image was originally recorded, not when the image was 
altered.
Procedure
[p] (PLAY) * Snapshot Screen * [MENU] * PLAY Tab * 
DPOF Printing
See page 125 for details.
Adjusting the Brightness of an Existing Snapshot 
(Brightness)
Selecting Images for Printing (DPOF Printing)
B 
						

							116Other Playback Functions (PLAY)
Procedure
[p] (PLAY) * [MENU] * PLAY Tab * Protect
IMPORTANT!
• Note that even if a file is protected, it will be deleted if you perform the format 
operation (page 158).
NOTE
• Performing the above procedure while a CS group folder is displayed will protect all 
the images in the CS group folder. You can protect individual images in a CS group 
by performing the above procedure while the image is displayed.
Protecting a File Against Deletion (Protect)
OnProtects specific files.
1Use [4] and [6] to scroll through the files 
until the one you want to protect is displayed.
2Use [8] and [2] to select “On” and then 
press [SET].
An image that is protected is indicated by the 
› icon.
3To protect other files, repeat steps 1 and 2.
To exit the protect operation, press [MENU]. To unprotect a file, select 
“Off” instead of “On” in step 2 above.
All Files: 
OnProtects all files.1Use [8] and [2] to select “All Files: On” and then press [SET].
2Press [MENU].
To unprotect all files, select “All Files: Off” instead of “All Files: On” in 
step 1 above. 
						

							117Other Playback Functions (PLAY)
.To protect a specific image in a CS group
1.While CS image playback is in progress or paused (toggle by pressing 
[SET]), press [
2].
This will display the “CS Frame Edit” menu.
2.Use [8] and [2] to select “Protect” and then press [SET].
3.Use [4] and [6] to scroll through images until one you want to protect 
is displayed.
4.Use [8] and [2] to select “On” and then press [SET].
This will protect the image and display the › icon.
• To unprotect an image, select “Off” in step 4 and then press [SET].
5.After you are finished, select “Cancel” and then press [SET] to exit this 
operation.
NOTE
• Note that even if a file is protected, it will be deleted if you perform the format 
operation (page 158). 
						

							118Other Playback Functions (PLAY)
.To protect all the images in a CS group
1.While a CS group is displayed or while the images of a CS group are 
scrolling on the monitor screen, press [MENU].
2.Use [4] and [6] to select “PLAY” tab.
3.Use [8] and [2] to select “Protect” and then press [SET].
4.Use [4] and [6] to display the CS group you want to protect.
5.Use [8] and [2] to select “On” and then press [SET].
This will protect all the images in the group and display the › icon.
• To unprotect all of the images in the group, select “Off” in step 5 and then press 
[SET].
6.Press [MENU].
NOTE
• Note that even if a file is protected, it will be deleted if you perform the format 
operation (page 158). 
						

							119Other Playback Functions (PLAY)
Procedure
[p] (PLAY) * Snapshot Screen * [MENU] * PLAY Tab * Rotation
1.Use [8] and [2] to select “Rotation” and then press [SET].
Each press of [SET] will rotate the displayed image 90 degrees left.
2.When the displayed image is at the orientation you want, press 
[MENU].
NOTE
• A CS group or an image that is part of a CS group cannot be rotated.
• Rotation of movie images is not supported.
• Note that this procedure does not actually change the image data. It simply alters 
how the image is displayed on the camera’s monitor screen.
• An image that has been protected or zoomed cannot be rotated.
• The original (unrotated) version of the image will be displayed on the image menu 
screen.
Procedure
[p] (PLAY) * Snapshot Screen * [MENU] * PLAY Tab * Resize
You can reduce the size of a snapshot and save the result as a separate snapshot. 
The original snapshot is also retained. You can resize an image to one of three sizes: 
5M, 2M, VGA.
• Resizing a 3:2 or 16:9 size snapshot will create an image with an aspect ratio of 
4:3, with both sides cut off.
• The recording date of the resized version of the snapshot will be the same as the 
recording date of the original snapshot.
Rotating an Image (Rotation)
Resizing a Snapshot (Resize) 
						

							120Other Playback Functions (PLAY)
Procedure
[p] (PLAY) * Snapshot Screen * [MENU] * PLAY Tab * Trimming
You can crop a snapshot to trim parts you do not need, and 
save the result in a separate file. The original snapshot is 
also retained.
Use the zoom controller to zoom the image to the size you 
want, use [8], [2], [4], and [6] to display the portion of 
the image you want to cut out, and then press [SET].
• The image produced by cropping a 3:2 or 16:9 image will 
have an aspect ratio of 4:3.
• The recording date of the cropped image will be the 
same as the recording date of the original snapshot.
Procedure
[p] (PLAY) * Snapshot Screen * [MENU] * PLAY Tab * Copy
Files can be copied from the camera’s built-in memory to a memory card or from a 
memory card to built-in memory.
NOTE
• You can copy snapshots or movies you recorded with this camera.
Cropping a Snapshot (Trimming)
Copying Files (Copy)
Built-in * 
CardCopies all files from built-in camera memory to a memory card.
This option copies all the files in built-in camera memory. It cannot 
be used to copy a single file.
Card * 
Built-inCopies a single file on the memory card to camera built-in camera 
memory. Files are copied to the folder in built-in memory whose 
name has the largest serial number.
• You cannot copy a continuous shutter (CS) group image (page 
104).
1Use [4] and [6] to select the file you want to copy.
2Use [8] and [2] to select “Copy” and then press [SET].
Represents
snapshot area
Part of snapshot that is
currently displayed
Zoom factor