Canon Wireless Remote Rc6 Manual

11
You can check the registered information of a paired remote controller 
or remove a registration from the menu screen of the camera.
When the remote controller is paired correctly, the 12-digit number on 
the back of the remote controller (the Bluetooth address) is displayed 
on the camera’s LCD monitor. If the number is incorrect, remove the 
registration of remote controller and perform pairing again. For the 
operation procedure, refer to the page regarding BR-E1 in the Camera 
Instruction Manual....

12
1Set up the camera for remote 
control shooting.
Set the camera for still photo shooting.
 Set the drive mode of the camera to 
< > (remote control).
2Select the release method.
Set the release timing/movie shooting 
switch on the remote controller to the 
< > (immediate release) or < > (2-
sec. delay release) position.
3Take a picture.
When you press the release button 
on the remote controller, the camera 
automatically focuses (AF), and takes 
a picture when focus is achieved.
 The indicator...

13
1Set up the camera for remote 
control shooting.
 Set the camera for movie shooting.
 Set [ Remote control ] to [Enable] 
from the menu screen of the camera.
2Set the switch to < >.
 Set the release timing/movie shooting 
switch on the remote controller to the 
< > position.
3Shoot the movie.
When you press the release button 
on the remote controller, the indicator 
lamp lights up and movie shooting 
starts.
 When you press the button again, the 
indicator lamp blinks and movie 
shooting stops....

14
The Power Zoom Adapter is a lens accessory (sold separately).
For information on how to attach to the lens and operate the Power 
Zoom Adapter, refer to its Instruction Manual.
1Prepare the Power Zoom Adapter.
Attach the Power Zoom Adapter to 
the lens, then attach the lens to the 
camera.
 Set the zoom mode switch of the 
Power Zoom Adapter to the <
PZ> 
position.
2Set up the came ra for remote 
control shooting. 
 Set the drive mode of the camera to 
< > (remote control).
3Press the power zoom...

15
If the indicator lamp does not light up when you press a button on the 
remote controller, replace the battery. Use one lithium button cell battery 
CR2032.
Replacing the Battery
CR2032
Make sure to insert the battery with 
the positive (+) side face up, as 
indicated in the figure above. 

16
Type:Remote controller
Compliance standards: Bluetooth Specification Version 4.1  (Bluetooth low energy technology)
Transmission method: GFSK modulation 
Operating distance: Approx. 5 m/16.4 ft. from the camera in any direction * With no obstructions between the remote controller and camera and no radio interference
Power: Lithium button cell battery CR2032
Battery life: Approx. one year
Dimensions (W x H x D): Approx. 27.0 x 91.5 x 12.0 mm/1.06 x 3.60 x 0.47 in.
Weight: Approx. 14 g/0.49 oz....

17
Countries and Regions Permitting Wireless Communication Function Use
Use of wireless communication function is restricted in some countries and 
regions, and illegal use may be punishable under national or local regulations. To 
avoid violating wireless regulations, visit  the Canon Web site to check where use 
is allowed.
Note that Canon cannot be held liable for any problems arising from wireless 
communication function use in other countries and regions.
 Model Number
BR-E1: DS586111(including...

Wireless Communication Function
18
Model: DS586111
This device complies with Part 15 of the FCC Rules. Operation is subject to the 
following two conditions: (1) This device may not cause harmful interference, and 
(2) this device must accept any interference received, including interference that 
may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for class 
B digital devices, pursuant to Part 15 of the FCC Rules. These limits are designed 
to provide...

19
Numerics
2-sec. delay release ..........................8
A
AF start button ..................................8
B
Bluetooth ...........................................9......................................................8
C
Checking registered information .....11
Connecting ........................................9
H
Handling Precautions ........................6
I
Icons .................................................3
Immediate release ............................8
Indicator lamp...

The descriptions in this Instruction Manual are current as of February 2017. For 
information on the compatibility with any products introduced after this date, 
contact any Canon Service Center. For th e latest version Instruction Manual, 
refer to the Canon Web site.
CPA-E323-000 © CANON INC. 2017