Canon Sx50 Multimedia Projector Users Manual

							31
PROJECTING AN IMAGE FROM THE COMPUTER
Adjusting Keystone Distortion
If a projected picture has keystone distortion, correct it by using the keystone adjustment
feature.
1
2Select Keystone Adjustment.
“Keystone adjustment” appears on the
screen.
Correct keystone distortion.
Keystone distortion must be corrected
while “Keystone adjustment” is displayed
on the screen. (“Keystone adjustment”
disappears 10 seconds later.)
Press the [OK] button.
To reduce the length
of the upper edge,
press [^].
To reduce the length
of the left edge, press
[].
3
Remote controlTop control 
						

							32
PROJECTING AN IMAGE FROM THE COMPUTER
• The result of keystone adjustment is memorized. If the projector installation
position is the same as before, keystone adjustment is not required.
• When Keystone Adjustment is selected, signals are processed digitally. The
image may look different from the original one.
• The aspect ratio of the image may change when keystone is adjusted.
• Keystone can be adjusted vertically and horizontally within the range of +/-20
degrees. The amount of adjustment varies depending on the combination of the
amount of optical zooming, input signal type, and adjustment direction (vertical
or horizontal).
• If the keystone distortion is too large to adjust, move the projector installation
position.
• To cancel the keystone adjustment, press the [KEYSTONE] button again to
display [Keystone Reset]. Then, press the [OK] button. 
						

							33
PROJECTING AN IMAGE FROM THE COMPUTER
Selecting a Screen Mode
You can select one of four screen modes depending on the display resolution of your
computer.
• A screen mode can be selected by selecting “Screen settings” from the menu. (P57)
Full screen
Normal
Wide Screen
Tr u e si z e
• If the display resolution of the computer is higher than 1400 by 1050 dots, select
a lower resolution before starting projection.
• The upper, lower, left, and/or right portions of a projected image may be missing
depending on the selected display mode.
Select this to project an image displayed on the computer screen at
a 4:3 aspect ratio (W:H) (SXGA+ [1400 by 1050 dots] or XGA [1024
by 768 dots]).
The image displayed on the computer screen at a 5:4 (W:H) aspect
ratio is projected with it compressed vertically or horizontally.
Select this to project an image displayed on the computer screen at
a 5:4 (W:H) aspect ratio (SXGA) or on a wide screen of Macintosh.
Since the image is projected with it fitted to either the width or length
of the computer screen, the top and bottom portions or the leftmost
and rightmost portions of the image are missing.
Select this to project an image displayed on the computer screen at
a 16:9 (W:H) aspect ratio.
Since the image is projected with it fitted to the width of the
computer screen, the top and bottom portions of the image are
missing.
Select this if you want to project an image in its original size.
A clear image can be obtained because of no image processing.
This mode cannot be selected when the display resolution of the
computer is larger than 1400 by 1050 pixels. 
						

							34
PROJECTING AN IMAGE FROM THE COMPUTER
Selecting an Image Mode (Quality)
You can select one of four image modes. You can adjust the image quality (brightness,
contrast, sharpness, gamma, color) as you like.
Press the [IMAGE] button.
“IMAGE” appears on the screen,
allowing you to select a desired image
mode by pressing the [IMAGE] button
repeatedly.
[Standard]Select this to project an image with a similar quality to that of the
original image. An image is projected with a high regard for
reproduction of white.
[Presentation]Select this to project an image with a similar quality to that of the
original image. A bright and high-contract image is projected.
[Cinema]Select this to project a moving picture. A picture is projected with a
high regard for color tone reproduction.
[sRGB]Select this when you want to project an image from a sRGB-
compatible digital camera. 
An image is projected in the display mode conforming to the sRGB
Standard.
• The quality of the image projected in each image mode can be adjusted as
follows. For the adjustment method, refer to Image Adj. Menu. (P62)
· Brightness Adjust this when the image is too bright or dark.
· Contrast Adjust this to decrease or increase contrast of the entire 
image. 
· Sharpness Adjust this to soften or sharpen an image.
· Gamma/Dynamic gamma
Adjust this to obtain better balance of contrast.
· Screen color correction/Advanced color adjustment
Adjust this when color tones are different from those of the 
original image.
• The results of adjustments made by the user are saved for each of six types of
input signals. Once they are saved, images can be projected with the same
settings.
• An image mode can be selected by selecting “Image adj.” from the menu. (P49,
62)
Remote control
1 
						

							35
PROJECTING AN IMAGE FROM THE COMPUTER
Turning Off the Projector
• Turning off the projector again with the lamp in an unstable state shortly after
turning on the projector may shorten the lamp life. Wait at least 5 minutes before
turning off the projector again.
• Remove the AC power cord after the [POWER] indicator lights red after power-
off. Removing the AC power cord immediately can damage the lamp and
circuits.
• Using the projector for more than 24 hours continuously may shorten the life of
the lamp and internal optical components. Turn off the projector at least once in
24 hours and give it a rest for about one hour.
When the power is turned off, cooling of the lamp starts. Therefore, the projector
cannot be turned on again for about 90 seconds.
1
2Press the [POWER] button.
A confirmation message appears on the
screen.
To continue projection, wait until the
confirmation message disappears (about
4 seconds) or press a button other than
the [POWER] button.
Press the [POWER] button again while
the confirmation message is
displayed.
The POWER indicator goes out and
starts flashing red, starting to cool the
lamp.
When the [POWER] indicator lights red in
90 seconds, remove the power cord from
the AC outlet.
3
Remote controlTop control 
						

							36
PROJECTING AN IMAGE FROM THE COMPUTER
Setting up the Power Management 
Function
If the projector receives no signal input within 30 seconds, a countdown timer appears.
The lamp will turn off five minutes later and the projector will enter the power management
mode selected in advance.
You can select one of the following power management modes from the menu. (P70)
Ready mode
Select this mode to start projection immediately.
When the projector enters this mode, the lamp is turned off and its cooling starts. When
the lamp has been cooled down, the [POWER] indicator starts flashing red and green to
enter the ready status. Projection will restart if the input signal is reconnected or any
button on the top control or remote control is pressed.
Shutdown mode
Select this mode to turn off the projector automatically.
When the projector enters this mode, the lamp is turned off and its cooling starts. When
the lamp has been cooled down, the [POWER] indicator stops flashing red and stays lit
and the power is turned off.
When the lamp is being cooled in a power management mode (for 90 seconds),
the projector is inoperative.
The power management function can be disabled (OFF). 
						

							37
USEFUL FUNCTIONS AVAILABLE DURING PROJECTION
Blacking Out an Image 
Te m p o r a r i l y
[NO SHOW]
Useful when:
• You finished the presentation.
• You want to divert attendees’
attention from the screen.
Black out the image temporarily.
Blacking out an Image
The screen changes to black or blue.
Showing the Image Again
• A unique logo can be captured.
(P59)
• The company logo can be shown
while the image is blacked out.
(P60)
Remote control
Let’s take a look at the useful functions
available when you make a presentation
with a computer connected to the
projector.
Blacking Out an Image Temporarily
[NO SHOW]  ...................................... P37
Making an Image Larger/Smaller 
[D.ZOOM] .......................................... P38
Showing the Elapsed Time
[P-TIMER] .......................................... P39
Pointing to a Position with a Spotlight 
[SPOT] ............................................... P39
Freezing a Image
[FREEZE]........................................... P40 
Muting the Sound/Adjusting the 
Volume [MUTE/VOL]........................ P40
Operating the Mouse Using the
Remote Control ................................ P41
USEFUL FUNCTIONS AVAILABLE 
DURING PROJECTION 
						

							38
USEFUL FUNCTIONS AVAILABLE DURING PROJECTION
Moving the Image to the Desired
Position
If the enlarged image is larger than the
screen, you can move it so that the
desired portion of the image is displayed
inside the screen.
Move the image vertically and horizontally
to display the desired portion on the
screen.
• The zoom ratio is 1x to 12x.
• The enlarged image can also be
frozen.
Making an Image Larger/
Smaller
[D.ZOOM]
Useful when:
• Making a small graph larger during
presentation.
• Moving unnecessary information off
the screen to focus on the current
subject.
Make the projected image larger/smaller.
Making the Image Larger
Press this button repeatedly until the
image becomes the desired size.
Making the Image Smaller
Press this button repeatedly until the
image becomes the desired size.
• Pressing the [D.ZOOM] button 
displays the magnification on the 
screen.
• Pressing the [OK] button cancels 
the digital zoom function.
Remote control
Remote controlTop control 
						

							39
USEFUL FUNCTIONS AVAILABLE DURING PROJECTION
Indicating a Position with a
Spotlight
[SPOT]
Useful when:
• You point to a portion of an image
that should draw attendees’
attention.
Point to a desired portion of the projected
image with a pointer.
Showing the Pointer
A pointer appears at the center of the screen
and the image becomes dark excepting the
pointer.
Multiple types of pointers are supported and
you can select a desired pointer by pressing
the [SPOT] button repeatedly.
Moving the Pointer
Move the pointer to a desired position.
To cancel the SPOT function, press the [OK]
button. 
The normal screen appears.
Remote control
Showing the Elapsed Time
[P-TIMER]
Useful when:
•  You want to manage the proceedings
of the presentation.
The timer indicating the elapsed time (00:00
to 59:59) is shown in the lower right corner
just like the stopwatch.
Starting the Timer
Pressing this button once shows the timer
and starts the timer.
Stopping the Timer
Pressing this button once again stops the
timer.
Canceling the P-TIMER function
When you pressing this button once again,
the timer disappears.
Remote control 
						

							40
USEFUL FUNCTIONS AVAILABLE DURING PROJECTION
Freezing the Picture
[FREEZE]
Useful when:
• You want to perform a computer
operation which is irrelevant to the
proceedings of the presentation.
• You want to stop a moving image.
Freeze the moving image.
Freezing an Image
“FREEZE” icon is shown on the screen.
Canceling the FREEZE function
To cancel the FREEZE function, press this
button again.
The frozen image can be expanded
or compressed.
Remote control
Muting the Sound/
Adjusting the Volume
[MUTE]
Useful when:
•  You want to mute the sound from the
projector immediately.
• You want to adjust the volume level
of the projector speaker.
Mute the sound temporarily or adjust the
volume level.
Muting the Sound
“MUTE” icon is shown on the screen.
Canceling the MUTE function
To cancel the MUTE function, press this
button again.
Pressing the [VOL +/-] button also cancels
the MUTE function.
Adjusting the Volume
Pressing the [+]/[-] button shows a Volume bar
appears on the screen. (If the volume is not
adjusted with the [+]/[-] button in about 4
seconds, the Volume bar disappears.)
The MUTE function can be used from
both the remote control and top control.
Remote control
Top control