Canon scanner CanoScan FB 630P User Manual

							21
Selecting the Film Adapter Unit
The Scan from setting in the Prefs. tab cannot be used to select the Film
Adapter Unit as an image source. Follow the procedure below to select the
Film Adapter Unit for use with your system.
1. For [Scan from] in the Prefs. tab, select [Platen].
2. Click the [Easy Scan] check box off.
3. Start ScanGear Toolbox CS and click the button such as Copy or Custom to
open the TWAIN driver display. For any setting other than when [Show
Toolbox] is selected under [When Scanner Push Button pressed], you open
the TWAIN driver display by pressing the Start button on the front of the
scanner.
4. In the TWAIN driver, select the Film Adapter Unit for the image source. If
you are using ScanGear CS, click the Scanner tab (the tab with the name
of the Scanner) and select the image source on the Scanner sheet  in the
Advanced Mode. You can select the image source also in the Simple
Mode.
5. Use the TWAIN driver to execute previewing or scanning images. 
						

							22
Using ScanGear Toolbox CS
Using ScanGear Toolbox CS is as easy as clicking the appropriate button on the
toolbar or selecting the appropriate option from the shortcut button pop-up
menus.
ScanGear Toolbox CS can only be closed by right-clicking the
shortcut button and selecting [Exit ScanGear Toolbox] from the
pop-up menu.
When a scan is initiated, the image is loaded into the registered driver or
program. The TWAIN driver such as ScanGear CS or CanoCraft CS can be
automatically launched at this point, allowing the image to be previewed and
adjusted, depending on whether Easy Acquire has been turned on or off in the
setting tab of each function.
Scanning with Easy Acquire On
When Easy Acquire is on, the registered program is launched directly and the
TWAIN driver is not launched at all. Whenever a toolbar button is clicked (or
shortcut button pop-up menu option selected), the final scan of the image is
initiated, the progress dialog displays and the functions of the button are
carried out as specified in the tab. 
						

							23
Scanning with Easy Acquire Off
When Easy Acquire is off, the TWAIN driver is first launched to allow a preview
scan and adjustments. After the TWAIN driver is used to complete the final
scan, the registered driver or program is launched and the scanned image is
loaded into it.
Progress Dialog
The progress dialog shows the selected settings while
the progress bar at the bottom shows how far the
scan has progressed. If the [Cancel] button on this
dialog is pressed, the scan stops and the remainder of
the function is canceled. If the [Change Settings]
button on this dialog is pressed, the scan stops, the
remainder of the function is canceled, and Prefs. tab
will appear. 
						

							24
Sending Faxes
Sending Faxes When Easy Acquire is On
1. Click the [Fax] button. The scan will initiate and display the progress
dialog.
2. The scanned image will be sent to the registered fax program.
Sending Faxes When Easy Acquire is Off
1. Click the [Fax] button. The TWAIN driver’s control panel will display.
2. Click the [Preview] button, check the preview image and adjust as
required.
3. Click the [Scan] button. The scanned image will be sent to the fax program
and prepared for transmission.
Sending Mail
Sending Mail When Easy Acquire is On
1. Click the [Mail] button. The scan will initiate and display the progress
dialog. 
						

							25
2. When the scan is complete, a new message window is opened in the mail
program and the scanned image is included as an attachment. The
message is ready to send after you specify the address and subject.
Sending Mail When Easy Acquire is Off
1. Click the [Mail] button. The TWAIN driver’s control panel will display.
2. Click the [Preview] button, check the preview image and adjust as
required.
3. Click the [Scan] button. When the scan is complete, a new message
window is opened in the mail program and the scanned image is included
as an attachment. The message is ready to send after you specify the
address and subject.
Copying
Copying When Easy Acquire is On
1. Click the [Copy] button. When [Multiple Copies] is on, the following dialog
appears. Specify the number of copies to print and click [OK]. The scan will
initiate and display the progress dialog. 
						

							26
2. When the scan is complete, it will print out on the registered printer.
Copying When Easy Acquire is Off
1. Click the [Copy] button. When [Multiple Copies] is on, the following dialog
appears. Specify the number of copies to print and click [OK].
TheTWAIN driver’s main panel will display.
2. Click the [Preview] button, check the preview image and adjust as required.
3. Click the [Scan] button. When the scan is complete, it will print out on the
registered printer. 
						

							27
Saving
Saving When Easy Acquire is On
1. Click the [Save] button. The scan will initiate and display the progress
dialog.
2. When the scan is complete, the image will be saved with the root name
and numbering system specified in the Prefs tab.
Saving When Easy Acquire is Off
1. Click the [Save] button. The TWAIN driver’s control panel will display.
2. Click the [Preview] button, check the preview image and adjust as
required.
3. Click the [Scan] button. When the scan is complete, the image will be
saved with the root name and numbering system specified in the Prefs tab.
Custom Functions 1-3
When Easy Acquire is On
1. Click the [Custom 1 (2 or 3)] button. The scan will initiate and display the
progress dialog.
2. When the scan is complete, the program registered with the button will
launch and display the scanned image. 
						

							28
When Easy Acquire is Off
1. Click the [Custom 1 (2 or 3)] button. The TWAIN driver’s control panel will
display.
2. Click the [Preview] button, check the preview image and adjust as re-
quired.
3. Click the [Scan] button. When the scan is complete, the program
registered with the button will launch and display the scanned image. 
						

							29
Using ScanGear Toolbox CS without Displaying a Toolbar
You can set the ScanGear Toolbox CS to launch a function of the ScanGear
Toolbox CS, such as Copy or Fax immediately without displaying a toolbar, by
pressing the start button in front of the scanner.
The function described here is not valid with a scanner which does
not have the start button.
In the item “When Scanner Push Button pressed” from the pop-up menu
displayed by right-clicking the short-cut icon or in the Prefs. tab, specify which
function will launch by pressing the start button on the scanner.
Set here 
						

							30
You can specify a function from Show Toolbox/Fax/Mail/Copy/Save/Custom1  (2, 3).
When [Show Toolbox] is specified, the toolbar appears when you press the
start  button.
Otherwise, the specified function will launch immediately when you press the
start button