Home > Canon > Scanner > Canon scanner CanoScan D1250U2F User Manual

Canon scanner CanoScan D1250U2F User Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Canon scanner CanoScan D1250U2F User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1335 Canon manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							41
    chapter 3
    What is on the
    screen?
    Glossary Contents
    IndexEditing a Special Tone Curve Directly
    In the Special Tone Curves graph you can edit the curve directly.
    Click on the curve and drag each curve anchor point until the desired effect
    is achieved. To remove an anchor point, drag the anchor point off the
    graph area, or right click the anchor point.
    Here are some hints for editing curves:
    •C
    urve handles are drawn on a white background as a red dot to signify
    that they are editable. When the cursor is over the handle, it changes to a
    crosshair.
    •C urve end points can be selected and dragged to any point in the curve
    but cannot be deleted.
    •U p to 15 points can be added to a curve by clicking anywhere in the curve
    box.
    • If you drag a point outside of a curve box, it will be deleted from the curve
    and a new curve will form with the remaining points.
    • The x and y axes on the curve chart represent the input image color and
    output image color. When you add a handle to the curve and drag that
    handle toward the white areas, the preview image tones are adjusted to
    reflect the change.
    •M ore than one handle cannot be positioned on a vertical line but more
    than one handle can be positioned on a horizontal line so you can have
    several handles on a horizontal line. 
    						
    							42
    chapter 3
    What is on the
    screen?
    Glossary Contents
    IndexThe Halftone Sheet
    The Halftone sheet is displayed only when Black and White has been se-
    lected for the Color Mode on the Advanced Mode Main window. You can
    set only Threshold in this sheet.
    Threshold
    Threshold determines whether portions of an original are scanned as black
    or white. Drag the slider left to make the image lighter or drag it righ\
    t to
    make the image darker. Or you can also enter a value ( 0 - 255) directly into
    the entry box to the right of the slider.
    Setting the threshold value higher causes the black portions of the image to
    increase. Setting it lower, causes the white portions to increase. 
    						
    							43
    Glossary Contents
    Index chapter
    4
    Multi-Photo Scan
    Multi-Photo Scan
    Multi-Photo Mode (Simple mode)
    Multi Crop (Advanced mode) 
    						
    							44
    chapter 4
    Multi-Photo
    Scan
    Glossary Contents
    IndexMulti-Photo Scan
    Multi-Photo Scan is used to scan two or more photos in a single operation.
    It causes the scanned images to appear individually in new windows in th\
    e
    application program. If you place a photo crookedly (within approximately
    10 degrees) on the platen, this function will straighten it automatically.
    Placing the Photos
    W
    ith the Multi-Photo Scan function, the gap between photos is detected
    using the rear white background of the document cover.
    When you place the photos on the platen, note the following; •This function will not  work correctly with a photo that appears
    whitish overall or has white around the edges.
    • This function will not work correctly with items other than photos,
    especially printed or hand-written text on white paper (documents or
    business card).
    • Keep more than 1 cm between the photos and edges of the platen.
    • Up to 10 photos can be processed.
    A4L
    T R B
    5 A
    4
    L
    T R
    B5 
    						
    							45
    chapter 4
    Multi-Photo
    Scan
    Glossary Contents
    IndexMulti-Photo Mode (Simple Mode)
    Procedures
    1.
    Place the photos on the scanner platen.
    2. Start ScanGear CS-U.
    3. In the ScanGear CS-U Simple Mode Main window, click the [Multi-
    Photo Mode] button.
    4. The Multi-Photo Mode wizard will appear. Click the [Next] button. 
    						
    							46
    chapter 4
    Multi-Photo
    Scan
    Glossary Contents
    Index5.
    After pre-scanning, cropping and scanning are automatically
    performed on each photo. During these procedures, do not open the
    document cover. When Multi-Photo Mode scanning is finished, the
    ScanGear CS-U main window appears.
    6. Click the close box to close ScanGear CS-U. The scanned images will
    open in the application software.
    7.  Save the images after adjusting them as required.
    •If ScanGear CS-U is launched from the application that
    cannot open two or more images at a time, a single
    image of the multiple photos is sent to the application
    when the [Multi-Photo Mode] function is used.
    Note 
    						
    							47
    chapter 4
    Multi-Photo
    Scan
    Glossary Contents
    IndexMulti Crop (Advanced Mode)
    Procedures
    1.
    Place the photos on the scanner platen.
    2. Start ScanGear CS-U.
    3. In the ScanGear CS-U Advanced Mode Main window, click the
    [Preview] button.
    4. The photos are previewed and appear in the preview window. Click
    the [Multi Crop] button.
    5. The images in the preview window are automatically cropped.
    •You can resize each cropped area by dragging the mouse.
    •Y ou can delete unnecessary image by right-clicking the mouse on
    the cropped area and clicking “Delete”. 
    						
    							48
    chapter 4
    Multi-Photo
    Scan
    Glossary Contents
    Index6.
    Click the [Scan] button.
    7. The scanning starts. During the procedure, do not open the the
    document cover. When the scanning is finished, the ScanGear CS-U
    window appears.
    8. Click the close box to close ScanGear CS-U. The scanned images will
    open in the application software.
    9. Save the images after adjusting them as required.
    •If ScanGear CS-U is launched from the application that
    cannot open two or more images at a time, a single
    image of the multiple photos is sent to the application
    when the [Multi Crop] function is used.
    Note 
    						
    							49
    Glossary Contents
    Index chapter
    5
    Settings in the
    Windows Control Panel
    Opening the Scanners and Cameras PropertiesDialog
    General Settings
    Events Settings
    Preferences Settings
    Color Management Settings 
    						
    							50
    chapter 5
    Setting in the
    Windows
    Control Panel
    Glossary Contents
    Index
    W
    indows Me
    Opening the Scanners and
    Cameras Properties Dialog
    You can specify some settings for ScanGear CS-U using the Scanners and
    Cameras properties dialog in the Windows Control Panel.
    Scanners and Cameras Properties dialog can be opened with the following
    procedures. Be sure to close ScanGear CS-U for this operation.
    1.Click the Control Panel.
    Windows XP:   In the Start menu, click Control Panel. In the Control
    Panel window, click Printer and Other Hardware, then Scanners and
    Cameras.
    Windows Me/98/2000:   On the Windows desktop, click the Start
    button, point to Settings, and click Control Panel. In the Control Panel
    window, double-click the Scanners and Cameras icon.
    2.Windows XP/Me:   In the Scanners and Cameras window, double-
    click the name of the Scanner.
    Windows 98/2000:   In the Scanners and Cameras Properties
    window, click the name of the scanner, and click the Properties
    button.
    W indows 98
    W indows XP 
    						
    All Canon manuals Comments (0)

    Related Manuals for Canon scanner CanoScan D1250U2F User Manual