Canon scanner CanoScan 9900F User Manual

9
Try Scanning
8Click [Scan].
The final scan will start. 
9Click   or   (close box) in the ScanGear CS  
window to close it.
The scanned image will appear in the PhotoStudio window.
10 Save the scanned image.
Click the [File] menu and select [Save As]. Select the folder 
where you wish to store the image file, enter a file name, 
select a file type (JPG format is recommended) and click [Save].
11 Click   or   (close box) in the PhotoStudio 
window to close it.
• If the scanner does not perform as...

10
Using the Scanner Buttons
You can use the four convenient buttons on the scanner’s front panel to scan and perform related tasks 
easily with a single touch of the button. Place an item on the document glass of the scanner before pressing 
a button.
 
• To use these buttons, ScanGear CS, CanoScan Toolbox, ArcSoft PhotoBase and Presto! 
PageManager (Windows)/Acrobat Reader (Macintosh) should be installed from the 
CanoScan Setup Utility CD-ROM.
 COPY Button
To print (copy) the scanned image with a...

11
Scanning Film
You can scan 35 mm film (strips or slides) as well as 120 and 4 x 5 format film with this scanner.
Positioning the Film 
Use the following procedures to insert the film into the film guide. Make sure that the FAU cable is 
connected properly. If the scanner power is not on, press the power switch to turn it on (p. 7).
1Remove the protective sheet from the document cover. 
When you finish scanning, fit the holes at the bottom end of the protective sheet over the tabs at the bot-
tom of...

12
Scanning Film 
Slides
Position the film guide for slides on the document glass (see Step 3) 
and place one or more slides face down in the film guide as shown on 
the right. 
3Place the film guide on the document glass of the scanner.
Align the smaller tab on the side of the film guide with the FILM mark on the document glass of the 
scanner. 
4Close the document cover.
Scanning Film 
The following steps explain how to scan films with ArcSoft PhotoStudio.
• If there is a gap between the film guide and...

13
Scanning Film
3In the [Select source] category, select [Film].
4In the [Type of original] category, select [Negative] 
or [Positive].
In ScanGear CS’s Simple Mode, the settings for film scanning 
are pre-set so that 35 mm film can be scanned and printed at 
the photo size. The Output Resolution is pre-set to 200 dpi and 
the Print Size to the photo size (8.9 x 12.7 cm/3.5 x 5 in.).
5Click [Preview].
ScanGear CS will display the preview image(s).
Multiple images will appear frame by frame.
6Place check...

14
Scanning Film 
7Click [Scan].
The scanner will start scanning the items.
After the scan is complete, click the ScanGear CS close box 
(  for Windows or   for Macintosh).
The scanned image will appear in ArcSoft PhotoStudio.
8Save the scanned image.
Click the [File] menu and select [Save As]. Select the folder 
where you wish to store the image file, enter a file name, 
select a file type (JPEG format is recommended) and click 
[Save].
9Click   or    (close box) in the PhotoStudio 
window to close it....

15
Specifications
*1 Available only when scanning films.*2 USB 2.0 Hi-Speed mode/IEEE1394 (FireWire) mode. Transfer time to computer is not included.*3 Calibration processing time is not included.*4 Type of AC adapter depends on the area where the scanner is purchased.
• Specifications are subject to change without notice.CanoScan 9900F
Scanner TypeFlatbed
Scanning ElementCCD 6-line color
Light SourceCold cathode fluorescent lamp
Optical Resolution3200 x 6400 dpi
Selectable Resolution25 - 9600 dpi...

16
System Information
This form should be used to record the operating environment for the purchased scanner. 
If any problems occur with the scanner, you will need this information when you contact our Customer 
Support Help Desk. Be sure to record the information and store it in a safe location.
• This information is also required to request a repair under warranty. Make sure you record the 
information and store it in a safe location.
• Guaranteed servicing for this equipment will expire seven years...