Canon Projector WX 6000 User Manual

71
Adjusting the Image
User’s ManualProjectin
g an Ima
ge
Adjusting the Image Size
The size of the projected image can be adjusted by pressing the ZOOM button on the 
remote control or the LENS button on the projector. Change the projector installation posi-
tion if your desired image is too large or too small to adjust it with the zoom function. 
(P156)
1Press either the ZOOM button on the remote control or the LENS button on the projec-
tor twice in order to display the window shown below.
Push twice...

Adjusting the Image
72
2Press the pointer buttons to adjust the image size.
3When the desired image size is selected, press the OK button or the ZOOM button.
When the Short Fixed Lens (RS-IL03WF) is attached, zoom adjustment cannot 
be performed.
Use the [] button on the remote control, or the UP button on the projector to 
increase the image size.
Use the [] button on the remote control, or the DOWN button on the projector to 
decrease the image size.
Remote controlProjectorRemote control
Screen 

73
Adjusting the Image
User’s ManualProjectin
g an Ima
ge
Adjusting the Focus
To adjust the focus, press the FOCUS button on the remote control or the LENS button on 
the projector.
For the projection distances of the lens unit, refer to page 156.
1Press either the FOCUS button on the remote control or the LENS button on the pro-
jector in order to display the window shown below.
2Press the pointer buttons to adjust the focus.
3When the focus is adjusted optimally, press the OK button or the FOCUS...

Adjusting the Image
74
Adjusting the Image Position
To adjust the screen position up, down, left, or right, press the LENS-SHIFT button 
(WUX5000 / WUX4000) or SHIFT button (WX6000 / SX6000) on the remote control, or the 
LENS button on the projector. This function is referred to as “lens shift”. It can change the 
projected screen to the most suitable position by moving the position of the lens up/down/
left/right. (P160)
1Press either the LENS-SHIFT button (WUX5000 / WUX4000) or the SHIFT button...

75
Adjusting the Image
User’s ManualProjectin
g an Ima
ge
2Press the pointer buttons to adjust.
3When the desired position is reached, press the OK button. 
■Resetting the Position
The lens position after movement with the lens shift function is not returned when the 
power is turned off. To return it to its original position, perform reset.
During screen position adjustment, press and hold the  LENS-SHIFT button (WUX5000 / 
WUX4000) or SHIFT  button (WX6000 / SX6000) on the remote control, or the  LENS...

Adjusting the Image
76
Adjusting Keystone Distortion
The D.SHIFT/KEYSTONE button (WUX5000 / WUX4000) or KEYSTONE button 
(WX6000 / SX6000) can be used to correct keystone distortion.
1Press the D.SHIFT/KEYSTONE button (WUX5000 / WUX4000) or KEYSTONE button 
(WX6000 / SX6000) to display the window in the center illustration below.
 Keystone can be adjusted within the range of ±20 degrees. If the keystone distortion is 
too large to adjust, move the projector installation position so that it is completely...

77
Adjusting the Image
User’s ManualProjectin
g an Ima
ge
2Press the pointer buttons to adjust.
3When keystone distortion has been corrected, press the OK button.
■Resetting the Keystone Adjustment
Perform the following steps to reset the keystone adjustment.
Press the D.SHIFT/KEYSTONE button (WUX5000 / WUX4000) or KEYSTONE button 
(WX6000 / SX6000) twice to display the [Keystone reset] window.
Then, select [OK] with the [ ] button, and press the OK button.
Remote control
Projector
[ ] button
Reduces the...

78
Selecting an Image Mode
You can select an image mode to suit the projected image.
In each image mode, you can further adjust the brightness, contrast, sharpness, gamma, 
color adjustment, advanced adjustment, and lamp mode (WUX4000). (P109)
■Image Modes
The image modes which can be selected vary somewhat depending on the selected 
input signal.
Image 
Mode
Compatible input signals
Explanation
Digital PC
Analog PC
(WUX5000 / WUX4000)Analog PC-1, 2
(WX6000 / SX6000)
HDMI (when [HDMI 
In] is [Computer])...

79
Selecting an Image Mode
User’s ManualProjectin
g an Ima
ge
■How to Select an Image Mode
Press the IMAGE button on the remote control to select.
The image mode changes each time the IMAGE button is pressed. (The displayed image 
modes vary depending on the selected input signal.)
You can also select any image mode from the [Image mode] menu. (P109)
 User settings 1 - 5 are displayed when the desired image settings have been created 
and stored using the user memory function in the image adjustment...

80
Turning Off the Projector
1Press the POWER button to display the window shown below.
When this window is displayed, press the POWER button again to turn off the power.
The lamp goes off, the [STAND BY] indicator starts flashing in red and the cooling 
process starts.
2Disconnect the power cord from the electrical outlet.
If the power plug is left connected, the [STAND BY] indicator will switch from flashing 
to constantly illuminated after the cooling process is completed.
 You cannot turn the...