Canon Projector SX80 Mark II User Manual

							141Troubleshooting
Appendix
■The projected image is blur.
■You cannot project an image appropriately.
■The projector is forced to be turned off.
Cause Countermeasure
The image is out of focus. Adjust the focus. (P59)
The distance to the screen is too 
short.Check whether the distance to the screen is appropriate. If 
the distance is shorter than approximately 1.2m (3.9), the 
projector cannot focus on the screen. (P35, P151)
The projector is not placed straight 
in front of the screen.Check whether the projector is placed obliquely to the 
screen. A slight error in the projection angle can be cor-
rected through the keystone adjustment function. (P60)
The projector has been moved to a 
place where the temperature var-
ies a lot.When the projector is moved from a low-temperature place 
to a high-temperature place, condensation may form on the 
lens. The condensation will evaporate a while later and the 
projector will be able to project a normal image.
The lens is stained. Clean up the lens. (P143)
The tracking is bad. Adjust the tracking with the AUTO PC or Tracking function. 
(P57, P82)
Cause Countermeasure
The projected image is inverted in 
the vertical or horizontal direction.The ceiling mounted/rear projection setting is incorrect. 
Check the [Image flip H/V] setting in the [Display settings] 
menu. (P87)
Using a VGA cable in which some 
pins are not connected. Use a supplied VGA cable (for SX800).
 If you use a commercial VGA cable, make sure to use a 
cable in which all pins are connected.
Cause Countermeasure
The air intake or exhaust vent is 
blocked.
Check whether the air intake or exhaust vent is blocked. If the 
air intake or exhaust vent is blocked, the temperature inside 
the projector rises and the power is automatically turned off 
to protect the projector. (The WARNING lamp flashes once.)
Wait until the internal temperature gets down, and then turn 
on the projector without blocking the intake and exhaust 
vents. (P24, P25, P49)
The air filter is dirty. Check whether the bottom air filter is clogged with dust.
If the air filter is clogged, clean or replace the air filter. (P144)
The lamp has exploded (or it is 
defective).Check whether the lamp has exploded.
If the lamp has exploded, replace the lamp according to 
Lamp Handling Precautions on page 18. Check the lamp 
by replacing it with a spare lamp if you have one. (P18, 
P145, P146) 
						

							Troubleshooting
142
■You cannot operate the remote control.
The operating temperature is inap-
propriate.Check whether the operating temperature is 5 to 35°C. (P20)
If you use the projector at 2300 meters or higher above sea 
level, contact your dealer.
Other reasons The projector may be damaged. Contact your dealer.
Cause Countermeasure
Batteries are not installed properly 
or they have run out.Check whether batteries are installed correctly. If batteries 
are installed correctly, replace them with new batteries. (P31)
You are operating the remote con-
trol from the outside of the remote 
control operating range.Check whether you are operating the remote control within 
the remote control operating range. (P31)
There is an obstacle between the 
projector and the remote control.Remove the obstacle between the infrared remote receiver 
of the projector and the remote control or point the remote 
control to an obstacle-free path.
You are operating the remote con-
trol under an inappropriate operat-
ing environment.Check whether the infrared remote receiver of the projector 
is exposed to direct sunlight or strong light of lighting appa-
ratus. (P31)
The channel setting of the remote 
control does not match with the 
setting of the projector.Check whether the channel setting of the remote control has 
been changed. You can check the [Remote control] setting 
in the [System settings] menu. (P107)
The key lock function is prohibiting 
the remote control operation.Check whether [Key lock] is enabled to disable the remote 
control operation.
In the System settings menu, set [Key lock] to [Off]. (P105) Cause Countermeasure 
						

							143
Appendix
Maintenance
Cleaning the Projector
Clean the projector frequently to prevent dust from settling on the surface.
A dirty lens may ruin the quality of the projected image.
Wipe the projectors main unit softly with a soft cloth.
If the projector is heavily soiled, soak the cloth in water with a small amount of detergent 
in it, squeeze the cloth very well, and then wipe the projector with it. After cleaning, wipe 
the projector with a dry cloth.
 The main unit is very hot immediately after turning off the projector. Wait until the projector 
cools down sufficiently (more than 1 hour) before cleaning the projector. Otherwise, you may 
get burned or injured.
 Before cleaning the projector, be sure to remove the power plug from the AC outlet. Other-
wise, electric shock or fire may result.
 Never use volatile cleaning liquid or benzine, as these may damage the finish of the pro-
jector.
 When using a chemical dust cloth, make sure to read the instructions thoroughly.
 When cleaning the projectors lens, use a commonly available air blower or lens cleaning 
paper. The lens surface is easily damaged, so do not use a hard cloth or tissues.
Caution
When Not Used for an Extended Period of Time
Be sure to attach the lens cap on the lens and store in the supplied carrying bag. 
						

							Maintenance
144
Cleaning and Replacing the Air Filter
An air filter is installed in the air intake vent on the bottom of the main body to protect the 
internal lens and mirror from dust. Should the air filter become clogged with dust, the pro-
jector may be damaged since it will block the air flow into the projector and raises the 
internal temperature of the projector. The following screen is displayed when turning on 
the projector if the air filter needs to be cleaned. Clean the air filter if such is the case.
■Cleaning the Air Filter
 Turn the projector upside down, remove the cover by pushing the latch, remove the air 
filter, and clean it with a vacuum cleaner.
 When cleaning dust off the rear exhaust vent and bottom air intake vent, bring the vac-
uum cleaner nozzle close to them directly.
 If the above screen is displayed when turning on the projector after cleaning the air fil-
ter, select [Yes].
■Replacing the Air Filter
Make sure to replace the air filter when replacing the lamp.
Follow the following procedure when replacing the air filter.
1Turn off the projector, disconnect the 
power plug from the AC outlet, and let 
the projector stand for at least 1 hour.
2Remove the filter cover by pushing the 
position of the arrow.
3Remove the air filter.
4Install a cleaned or new air filter.
5Install the filter cover securely without 
any space.
 Only [], the OK button, and the POWER button 
are available while this screen is displayed (When 
you press the POWER button, Push POWER button 
again to turn off power. message appears).
 After this screen has been displayed for 10 seconds 
and disappeared, all buttons become operable.
 Handle the air filter carefully. If damaged, the air filter will not work appropriately
 An air filter can be ordered from your dealer. 
						

							145Maintenance
Appendix
Replacing the Lamp
When the time of use of the lamp exceeds the certain amount of time, the following mes-
sage (two types) is displayed for 10 seconds every time the projector is turned on.
1,800 - less than 2,000 hours
 After this screen has been displayed for 10 seconds and disappeared, all buttons 
become operable.
 This message will not be displayed again if you select [Cancel] in response to the mes-
sage Do you want to display this message again?.
Over 2,000 hours
 After this screen has been displayed for 10 seconds and disappeared, all buttons 
become operable.
 You can check the time of use of the lamp in [Lamp counter] in the [System settings] 
menu (P109).
■About the Replacing Lamp
This projector uses the following lamp.
Lamp type No.RS-LP05
 Be sure to use the specified lamp.
 A lamp can be ordered from your dealer.
 When replacing the lamp, turn off the projector, wait until the cooling fan stops, disconnect the 
power plug from the AC outlet, and let the projector stand for at least 1 hour. Otherwise, you 
may get burned because the main unit is very hot immediately after the projector is turned off.
 Do not touch the inner glass surface when you replace the lamp. Otherwise, the projector s 
performance may degrade.
 Make sure to handle the lamp carefully and correctly since it may explode if it is scratched or 
shocked. If a lamp explodes, follow the instructions under If a Lamp Explodes on page 18.
 Do not remove screws unless specified.
Prepare the new lamp when this screen is dis-
played.
 Only [], the OK button, and the POWER 
button are available while this screen is dis-
played.
 When you press the POWER button, Push 
POWER button again to turn off power. mes-
sage appears.
Replace the lamp by referring to the procedure 
on page 146 when this screen is displayed.
 Only the POWER button is available while this 
screen is displayed.
 When you press the POWER button, Push 
POWER button again to turn off the power. 
message appears.
Caution 
						

							Maintenance
146
■Replacing the Lamp
1Turn off the projector, disconnect the 
power plug from the AC outlet, and let 
the projector stand for at least 1 hour.
2As shown in the figure, insert a flat-
head screwdriver in the gap and 
remove the lamp cover by raising it.
3Loosen two screws with a phillips-
head screwdriver and then pull up the 
handle.
* Pull up the handle as shown in the 
figure.
4Remove the lamp while holding the 
center of the handle.
5Fully insert a new lamp and secure it 
with two screws.
* After the installation, be sure to 
push down the handle.
6As shown in the figure, replace the 
lamp cover. Check whether the lamp 
cover is installed securely.
7Turn on the projector.
8Bring up the menu and select [System 
settings] -> [Other settings] -> [Lamp 
counter]. (P109)
9Select [Reset] -> [OK] to reset the 
lamp counter. 
						

							147
Appendix
Relationship between Aspect and Screen Aspect
This section describes the relationship between screen aspect (P62) and aspect (P65).
To project an image on the whole screen, select the most appropriate screen aspect ratio 
and aspect according to the aspect ratio of the screen and input signal type.
When Projecting an Image from a Computer
When the input signal is [ANALOG PC-1], [ANALOG PC-2], or [DIGITAL PC (SX80 II)], select 
screen aspect and aspect as follows according to the resolution of the image on the computer.
ScreenScreen Aspect 
Ratio SettingResolution of Com-
puter ScreenObject of ProjectionAspect Setting
[4:3]Project an image in a 
largest possible size on 
the screen.
[Auto]
(or [4:3])
Project an image in a 
largest possible size on 
the screen.
[4:3]
Project the computer 
screen in the original 
resolution.
[True size]
Project an image in a 
largest possible size on 
the screen.
[Auto]
Project the computer 
screen in the original 
resolution.
(WUXGA not select-
able)
[True size]
Project an image in a 
largest possible size on 
the screen.
[Auto]
Project the computer 
screen in the original 
resolution.
[True size]
[16:9]Project an image in a 
largest possible size on 
the screen.
[Auto]
Project an image in a 
largest possible size on 
the screen.
[Auto]
Project the computer 
screen in the original 
resolution.
[True size]
Project an image in a 
largest possible size on 
the screen.
[Auto]
Project an image in a 
largest possible size on 
the screen.
[Auto]
4:3
SXGA+
4:3
VGA, SVGA, XGA
4:3
WXGA
SXGA
5:4
16:9
SXGA+
4:3
VGA, SVGA, XGA
4:3
WXGA
SXGA
5:4 
						

							Relationship between Aspect and Screen Aspect
148
When Projecting an Image from Image Software
To project an image such as an image shot by a TV set, commercially available DVD software, 
or video camcorder (input signal [HDMI (SX80 II)], [VIDEO], [S-VIDEO (SX80 II)], [COMPO-
NENT]), select an aspect ratio according to the image software format as follows.
*1[Auto] cannot be selected for the aspect setting if the input signal type is [VIDEO].*2If an image from image software with aspect ratio of 16:9 is not projected correctly, select [16:9] 
as screen aspect.
*3If you project the 16:9 image with black borders at top and bottom such as in the terrestrial movie 
broadcasting, you can project the 16:9 image fully on the screen by selecting [Zoom] in [Aspect].
[Zoom] is available when [16:9] or [16:9 D. image shift] is selected for the screen aspect and 
[HDMI (480p)(SX80 II)], [COMPONENT (480p, 480i)], [VIDEO] or [S-VIDEO (SX80 II)] is selected 
for the input signal.
*4To perform keystone adjustment (P60), select [4:3] or [16:9] for [Screen aspect].
ScreenScreen Aspect Ratio 
SettingImage Software
 For matProjection ResultAspect
 Setting
[4:3][Auto]*1
[16:9]
[16:9 D. image shift]*4
[Auto]*2
[Zoom]*3
4:34:3
16:9
16:9
4:3
16:9
4:316:9 
						

							149 Relationship between Aspect and Screen Aspect
Appendix
When Projecting an Image from a Digital Camera or a USB 
Flash Memory (SX80 II)
The [Auto] mode is automatically selected for the aspect ratio when displaying an image 
from a digital camera or USB flash memory (selecting [USB] as the input signal).
The image is expanded fully on the screen with the screen aspect maintained.
*To perform keystone adjustment (P60), select [16:9] for [Screen aspect].
ScreenScreen Aspect Ratio 
SettingProjection ResultAspect Setting
[4:3][Auto]
[16:9]
[16:9 D. image shift]*[Auto]
4:3
16:9 
						

							150
Supported Computer Signal Types
This projector supports following signal types.
If your computer or AV equipment is compatible with any one of these signal types, the projectors 
auto PC function selects the input signal type to project an image appropriately.
ANALOG RGB
* The specifications in the table above are subject to 
change without notice.
* This projector does not support any computer sig-
nal of which dot clock is 170 MHz or higher.
DVI (SX80 II)
HDMI (SX80 II)
*Interlaced signal
COMPONENT
*Interlaced signal
Resolution 
(dots)Signal typeHorizontal 
frequency (KHz)Ve r t i c a l  
frequency (Hz)
640 x 480VGA31.469 59.94 
37.50 75.00 
37.861 72.81 
37.861 74.38 
43.269 85.01 
720 x 400 -31.469 70.09 
800 x 600SVGA34.50 55.38 
35.156 56.25 
37.879 60.32 
37.898 61.03 
38.00 60.51 
38.60 60.31 
46.875 75.00 
48.077 72.19 
53.674 85.06 
1024 x 768XGA44.028 54.63 
46.897 58.19 
47.00 58.31 
48.363 60.00 
48.496 60.02 
56.476 70.07 
58.032 72.00 
60.023 75.03 
60.314 74.92 
60.994 75.77 
62.04 77.07 
63.478 79.35 
68.677 85.00 
1280 x 768WXGA47.986 59.83 1280 x 80049.702 60.031360 x 768 -47.712 60.02 1152 x 864 -64.196 70.39 
1152 x 900 -61.17 65.28 
61.846 66.00 
71.399 75.64 
1280 x 960 -60.00 60.00 
1280 x 1024SXGA62.50 58.63 
63.337 59.98 
63.364 59.95 
63.735 60.01 
63.791 60.18 
63.899 60.00 
63.981 60.02 
71.694 67.19 
76.97 72.00 
79.976 75.03 
81.135 76.11 
1400 x 1050SXGA+ 63.981 60.02 1600 x 1200UXGA 75.00 60.00 640 x 480MAC LC 1334.967 66.60 640 x 480MAC13 35.00 66.67 832 x 624MAC16 49.725 74.55 1024 x 768MAC19 60.248 75.03 1152 x 870MAC21 68.681 75.06 1280 x 960MAC 75.00 75.08 
Resolution 
(dots)Signal type Horizontal 
frequency (KHz)Ve r t i c a l  
frequency (Hz)
640 x 480 D-VGA 31.469 59.94
800 x 600 D-SVGA 37.879 60.32
1024 x 768 D-XGA 48.363 60.00
1280 x 1024D-SXGA63.981 60.02
1400 x 1050 D-SXGA+ 63.981 60.02
Signal type Horizontal 
frequency (KHz)Ve r t i c a l  
frequency (Hz)
480p 31.469 59.94
576p 31.250 50.00
720p 37.500 50.00
720p 44.955 59.94
1080i* 28.125 50.00
1080i* 33.716 59.94
1080p 56.250 50.00
1080p 67.433 59.94
Signal type Horizontal 
frequency (KHz)Ve r t i c a l  
frequency (Hz)
480p 31.469 59.94
480i* 15.734 59.94
576p 31.250 50.00
576i* 15.625 50.00
720p 37.500 50.00
720p 44.955 59.94
1035i* 33.750 60.00
1080i* 28.125 50.00
1080i* 33.716 59.94
1080p 56.250 50.00
1080p 67.433 59.94