Canon Projector SX7 SX6 SX60 SX7000 User Manual
Here you can view all the pages of manual Canon Projector SX7 SX6 SX60 SX7000 User Manual. The Canon manuals for Projector are available online for free. You can easily download all the documents as PDF.
Page 31
![Page 31
31
SETTING UP THE PROJECTOR
Determining the Installation Position
Placing in Front of the Screen
Place the projector perpendicular to the screen
as far as possible.
Placing on a Level Place
Place the projector on a level place as far as pos-
sible.
zA slight error in the projection angle can be
corrected using the [KEYSTONE] button
(P50).
zA slight tilt can be corrected using the rear
adjustable foot. (P41)
zMake sure that the installation position is
free from any obstacle that may block the
exhaust...](http://img.usermanuals.tech/thumb/14/98762/w300_projector_manual_3919_d-30.png "Page 31
31
SETTING UP THE PROJECTOR
Determining the Installation Position
Placing in Front of the Screen
Place the projector perpendicular to the screen
as far as possible.
Placing on a Level Place
Place the projector on a level place as far as pos-
sible.
zA slight error in the projection angle can be
corrected using the [KEYSTONE] button
(P50).
zA slight tilt can be corrected using the rear
adjustable foot. (P41)
zMake sure that the installation position is
free from any obstacle that may block the
exhaust...")
31 SETTING UP THE PROJECTOR Determining the Installation Position Placing in Front of the Screen Place the projector perpendicular to the screen as far as possible. Placing on a Level Place Place the projector on a level place as far as pos- sible. zA slight error in the projection angle can be corrected using the [KEYSTONE] button (P50). zA slight tilt can be corrected using the rear adjustable foot. (P41) zMake sure that the installation position is free from any obstacle that may block the exhaust...
Page 32
Page 33
Table of contents/Safety Instructions Before Use Setting Up the Projector Projecting an Image from the Computer Projecting an Image from AV Equipment Useful Functions Available During a Presentation Setting Up Functions from Menus Maintenance Troubleshooting Appendix Index PROJECTING AN IMAGE FROM THE COMPUTER
Page 34
![Page 34
34
PROJECTING AN IMAGE FROM THE COMPUTER
Projecting an Image from the Computer
Connecting the Projector to the Computer
Connect the projector to the computer.
Connecting to Video Terminals
Supplied computer connection cable
To monitor output terminal
(mini D-sub 15-pin terminal)
Input Terminal-1
(ANALOG IN-1)Supplied computer
connection cable
Input Signal: Select [ANALOG PC-1] (P46)Computer
Projector
VGA cable
To monitor output terminal
(mini D-sub 15-pin terminal)
Input Terminal-2
(ANALOG...](http://img.usermanuals.tech/thumb/14/98762/w300_projector_manual_3919_d-33.png "Page 34
34
PROJECTING AN IMAGE FROM THE COMPUTER
Projecting an Image from the Computer
Connecting the Projector to the Computer
Connect the projector to the computer.
Connecting to Video Terminals
Supplied computer connection cable
To monitor output terminal
(mini D-sub 15-pin terminal)
Input Terminal-1
(ANALOG IN-1)Supplied computer
connection cable
Input Signal: Select [ANALOG PC-1] (P46)Computer
Projector
VGA cable
To monitor output terminal
(mini D-sub 15-pin terminal)
Input Terminal-2
(ANALOG...")
34 PROJECTING AN IMAGE FROM THE COMPUTER Projecting an Image from the Computer Connecting the Projector to the Computer Connect the projector to the computer. Connecting to Video Terminals Supplied computer connection cable To monitor output terminal (mini D-sub 15-pin terminal) Input Terminal-1 (ANALOG IN-1)Supplied computer connection cable Input Signal: Select [ANALOG PC-1] (P46)Computer Projector VGA cable To monitor output terminal (mini D-sub 15-pin terminal) Input Terminal-2 (ANALOG...
Page 35
35 PROJECTING AN IMAGE FROM THE COMPUTER zBefore connecting cables, turn off both the projector and computer. zIt may project an image inappropriately when projecting the digital PC signal in 1280 x 1024 or 1400 x 1050 depending on the type of computer or DVI cable (SX7/SX6/SX60). zThe USB terminal is used to use the remote control as the computer mouse. An image can- not be projected simply by connecting the USB cable. DVI cable Computer Projector To monitor output terminal (DVI terminal) Input...
Page 36
36 PROJECTING AN IMAGE FROM THE COMPUTER Connecting to an External Monitor You can display an image from the projec- tor to an external monitor. Connecting to AUDIO IN Termi- nals (SX7/X700) Connect an audio cable to the AUDIO IN ter- minal corresponding to the input image sig- nal if you want to use the projectors speaker. zYou can connect one external monitor. The multi-monitor display is not sup- ported. zThe projected image is displayed on the external monitor. zYou cannot output the input signal to...
Page 37
37 PROJECTING AN IMAGE FROM THE COMPUTER Connecting to AUDIO IN Termi- nals (SX6/SX60) Connect the audio cable to the AUDIO IN terminal if you want to use the projectors speaker. zUse an audio cable without a built-in resistor. Using an audio cable with a built-in resistor turns down the sound. zThe built-in speaker is monaural. zThe speaker plays the sound from the equipment which the audio cable is connected to regardless of the image input signal. Audio cable AUDIO OUT terminal AUDIO IN...
Page 38
![Page 38
38
PROJECTING AN IMAGE FROM THE COMPUTER
Starting Projection
Connect the power cord and turn on the projector to start the projection.
1Connect the power cord.
Fully insert the power cord plug into the socket.
The [POWER] indicator flashes red.
2Press the [POWER] button.
The [POWER] indicator flushes green, and
then lights in green.
zOnce the projector is turned off, it cannot be turned on for a while. Wait until the lamp is
cooled down and the [POWER] indicator lights in red.
Caution
Connect the Ground...](http://img.usermanuals.tech/thumb/14/98762/w300_projector_manual_3919_d-37.png "Page 38
38
PROJECTING AN IMAGE FROM THE COMPUTER
Starting Projection
Connect the power cord and turn on the projector to start the projection.
1Connect the power cord.
Fully insert the power cord plug into the socket.
The [POWER] indicator flashes red.
2Press the [POWER] button.
The [POWER] indicator flushes green, and
then lights in green.
zOnce the projector is turned off, it cannot be turned on for a while. Wait until the lamp is
cooled down and the [POWER] indicator lights in red.
Caution
Connect the Ground...")
38 PROJECTING AN IMAGE FROM THE COMPUTER Starting Projection Connect the power cord and turn on the projector to start the projection. 1Connect the power cord. Fully insert the power cord plug into the socket. The [POWER] indicator flashes red. 2Press the [POWER] button. The [POWER] indicator flushes green, and then lights in green. zOnce the projector is turned off, it cannot be turned on for a while. Wait until the lamp is cooled down and the [POWER] indicator lights in red. Caution Connect the Ground...
Page 39
![Page 39
39
PROJECTING AN IMAGE FROM THE COMPUTER
The countdown window is displayed for approximately 20 seconds, and then the guid-
ing message for the auto setup function appears.
Adjust the focus by performing the auto setup or the focus adjustment if you cannot
read the message due to out of focus. (P44, 49)
The LED illumination lamp blinks blue until the projection is started.
To project an image immediately, press the [OK] button.
zEnter a password if the Password input screen appears (P112, 113).
zYou can...](http://img.usermanuals.tech/thumb/14/98762/w300_projector_manual_3919_d-38.png "Page 39
39
PROJECTING AN IMAGE FROM THE COMPUTER
The countdown window is displayed for approximately 20 seconds, and then the guid-
ing message for the auto setup function appears.
Adjust the focus by performing the auto setup or the focus adjustment if you cannot
read the message due to out of focus. (P44, 49)
The LED illumination lamp blinks blue until the projection is started.
To project an image immediately, press the [OK] button.
zEnter a password if the Password input screen appears (P112, 113).
zYou can...")
39 PROJECTING AN IMAGE FROM THE COMPUTER The countdown window is displayed for approximately 20 seconds, and then the guid- ing message for the auto setup function appears. Adjust the focus by performing the auto setup or the focus adjustment if you cannot read the message due to out of focus. (P44, 49) The LED illumination lamp blinks blue until the projection is started. To project an image immediately, press the [OK] button. zEnter a password if the Password input screen appears (P112, 113). zYou can...
Page 40
![Page 40
40
PROJECTING AN IMAGE FROM THE COMPUTER
Adjusting the Image
Adjusting the Image Size (ZOOM).
Adjust the image size in accordance with the screen.
1Press the [ZOOM] button.
The Zoom adjustment window appears.
2Adjust the image size.
3Press the [OK] button.
zChange the projector installation position if your desired image size is too large or too small
to adjust with the zoom function (P30).
Zoom in:
Press [ ] for rough adjustment.
Press [>] for fine adjustment.
Zoom out:
Press [ ] for rough adjustment....](http://img.usermanuals.tech/thumb/14/98762/w300_projector_manual_3919_d-39.png "Page 40
40
PROJECTING AN IMAGE FROM THE COMPUTER
Adjusting the Image
Adjusting the Image Size (ZOOM).
Adjust the image size in accordance with the screen.
1Press the [ZOOM] button.
The Zoom adjustment window appears.
2Adjust the image size.
3Press the [OK] button.
zChange the projector installation position if your desired image size is too large or too small
to adjust with the zoom function (P30).
Zoom in:
Press [ ] for rough adjustment.
Press [>] for fine adjustment.
Zoom out:
Press [ ] for rough adjustment....")
40 PROJECTING AN IMAGE FROM THE COMPUTER Adjusting the Image Adjusting the Image Size (ZOOM). Adjust the image size in accordance with the screen. 1Press the [ZOOM] button. The Zoom adjustment window appears. 2Adjust the image size. 3Press the [OK] button. zChange the projector installation position if your desired image size is too large or too small to adjust with the zoom function (P30). Zoom in: Press [ ] for rough adjustment. Press [>] for fine adjustment. Zoom out: Press [ ] for rough adjustment....