Canon projector REALiS SX7 Maprojector Rk II User Manual

41
PROJECTING AN IMAGE FROM THE COMPUTER
The countdown window is displayed for approximately 20 seconds, and then the guid-
ing message for the auto setup function appears.
Adjust the focus by performing the auto setup or the focus adjustment if you cannot
read the message due to out of focus. (P46, 51)
The LED illumination lamp blinks blue until the projection is started.
To project an image immediately, press the [OK] button.
zEnter a password if the Password input screen appears (P116, 117).
zYou can...

42
PROJECTING AN IMAGE FROM THE COMPUTER
Adjusting the Image
Adjusting the Image Size (ZOOM)
Adjust the image size in accordance with the screen.
1Press the [ZOOM] button.
The Zoom adjustment window appears.
2Adjust the image size.
3Press the [OK] button.
zChange the projector installation position if your desired image size is too large or too small
to adjust with the zoom function (P32).
Zoom in:
Press [ ] for rough adjustment.
Press [>] for fine adjustment.
Zoom out:
Press [ ] for rough adjustment....

43
PROJECTING AN IMAGE FROM THE COMPUTER
Adjusting the Projection Angle
You can adjust the projection angle with the adjustable foot.
1Lift the front side of the projector and push the
adjusting foot lock button.
The adjustable foot extends.
2Adjust the projection angle while pushing the
adjustable foot lock button, and then release
the lock button.
The adjustable feet is fixed.
zWith the adjustable foot, the projection angle
can be adjusted up to 10 degrees.
zIf the projector is tilting in the lateral...

44
PROJECTING AN IMAGE FROM THE COMPUTER
Preparing the Computer
Determining the Output Resolution of the Computer
To make the most of the display performance of this projector, set output signal resolution
of the computer to an optimum value.
Windows 7
1. Open the [Control Panel] from the start
menu, then select [Appearance and Per-
sonalization] – [Adjust screen resolution] in
the [Control Panel Home].
2. Click the [Resolution] pull-down menu and
move the slider to select 1400 x 1050. If
this resolution...

45
PROJECTING AN IMAGE FROM THE COMPUTER
Macintosh OSX
1. Open the Apple Menu and select [System
Environment Setting].
2. In the System Environment Setting win-
dow, click the [Displays] icon to display
the Display window.
3. Select the [Display] tab and select 1400 x
1050 or a resolution closest to the output
signal resolution of the computer from the
[Resolution] list.
4. Close [System Environment Setting] win-
dow.
Projecting the Image from the Notebook Computer
You can turn on the external monitor...

46
PROJECTING AN IMAGE FROM THE COMPUTER
Performing the Auto Setup
With the auto setup function, the following set of adjustments is performed automatically
when projecting an image from a computer. You can start the projection only with this oper-
ation if the input signal has been appropriately selected.
1Select an input signal.
Select an appropriate input signal by following the steps in the Selecting an Input Sig-
nal section at the page 48 if you change the input signal due to changing the connec-...

47
PROJECTING AN IMAGE FROM THE COMPUTER
2Press the [AUTO SET] button.
The Auto setup window appears.
3Press the [AUTO SET] button again.
One or more functions highlighted in black are performed automatically.
zYou can perform this step by selecting [OK] with the [

48
PROJECTING AN IMAGE FROM THE COMPUTER
Selecting an Input Signal
You can select an input signal type.
Select an input signal from the followings:
ANALOG PC-1 : Analog signal Connecting with a DVI/Mini D-sub 15-pin cable
(supplied cable)
DIGITAL PC : Digital signal Connecting with a DVI digital cable
ANALOG PC-2 : Analog signal Connecting with a VGA cable or 5-BNC cable
Select an appropriate input signal before starting the auto setup function by following the
steps below if you change the input signal...

49
PROJECTING AN IMAGE FROM THE COMPUTER
3If the target input signal is unavailable from the list at the left, press the [>] button, and
then press the [ ] / [ ] button to select the target input signal from the list at the right.
4Press the [OK] button.

50
PROJECTING AN IMAGE FROM THE COMPUTER
„Selecting ANALOG PC-2
1Press the [INPUT] button.
The [INPUT] window appears.
2Select the second top item in the menu with the [INPUT] button.
The selection is toggled through available input signals from above.
3If the ANALOG PC-2 is unavailable from the list at the left, press [>], and then press [ ]
/ [ ] to select the ANALOG PC-2 from the list at the right.
4Press the [OK] button.
zSelect [ANALOG PC-2] for Input Terminal-2.
zYou can select any input signal...