Canon projector LVWX300UST User Manual

							 
— 55— 
Cleaning the Projector 
Cleaning the projector to remove dust and grime will help ensure trouble-free operation.  
Cleaning the Projector Mirror: 
 
When cleaning the projector’s lens, use a commonly available air blower or lens cleaning paper. 
The lens surface is easily damaged, so do not use a hard cloth or tissues. 
 Caution: 
1. Always turn the projector off and allow to cool for at least 30 minutes prior to cleaning. 
Caution: 
1. Never touch the projector mirror or Lens directly by hand. 
2. Do not use abrasive cleaners, solvents or other harsh chemical cleaners. 
 
    
						

							 
— 56— 
Using the Physical Lock 
Using the Kensington® Lock 
If you are concerned about security, attach the projector to a permanent object with the Kensington 
slot and a security cable.  
 
Note: 
Contact your vendor for details on purchasing a suitable Kensington security cable.  
 
Using the Security Bar 
In addition to the password protection function and the Kensington lock, the Security Bar helps 
protect the projector from unauthorized removal. 
See the following picture. 
 
 
    
						

							 
— 57— 
TROUBLESHOOTING 
Tips for Troubleshooting 
In each problem-specific section, try the steps in the order suggested. This may help you to solve 
the problem more quickly. 
Try to pin point the problem and thus avoid replacing non-defective parts.  
For example, if you replace batteries and the problem remains, put the original batteries back and 
go to the next step.  
Keep a record of the steps you take when troubleshooting: The information may be useful when 
calling for technical support or for passing on to service personnel. 
  
						

							 
— 58— 
LED Messages 
ERROR CODE MESSAGES POWER LED 
GREEN 
LAMP LED 
AMBER 
TEMP LED 
RED 
Power On ON OFF OFF 
Power Off ON OFF OFF 
Cooling Flashing OFF OFF 
Over Temperature OFF OFF ON 
Thermal Break Sensor error 4 blinks OFF OFF 
Lamp error OFF ON OFF 
Fan 1 6 blinks 1 blinks OFF 
Fan 2 6 blinks 2 blinks OFF 
Fan 3 6 blinks 3 blinks OFF 
Fan 4 6 blinks 4 blinks OFF 
Lamp Door Open 7 blinks OFF OFF 
DMD error 8 blinks OFF OFF 
Color wheel error 9 blinks OFF OFF 
 In the event of an error, please disconnect the AC power cord and wait for one (1) minute before 
restarting the projector. If the Power or Lamp LEDs are still blinking or any other situation that isnt listed 
in the chart above, please contact your service center. 
Image Problems 
Problem: No image appears on the screen 
1. Verify the settings on your notebook or desktop PC. 
2. Turn off all equipment and power up again in the correct order. 
Problem: The image is blurred  
1. Adjust the Focus on the projector. 
2. Press the Auto button on the remote control. 
3. Ensure the projector-to-screen distance is within the specified range. 
4. Check that the projector lens is clean. 
Problem: The image is wider at the top or bottom (keystone distortion)  
1. Position the projector so it is as perpendicular to the screen as possible.  
2. Use the Keystone button on the remote control to correct the problem. 
Problem: The image is reversed  
Check the Image Flip H/V setting on the Installation I menu of the OSD. 
Problem: The image is streaked  
1. Set the Frequency and Total Dots settings on the Computer menu of the OSD to the 
default settings. 
2. To ensure the problem is not caused by a connected PC’s video card, connect to 
another computer.  
Problem: The image is flat with no contrast  
Adjust the Contrast setting on the Image menu of the OSD. 
Problem: The color of the projected image does not match the source image. 
1. Adjust the Gamma settings on the Image menu of the OSD.  
						

							 
— 59— 
2. Adjust the Color Temperature settings on the Image->Advanced menu of the OSD. 
Lamp Problems 
Problem: There is no light from the projector  
1. Check that the power cable is securely connected. 
2. Ensure the power source is good by testing with another electrical device. 
3. Restart the projector in the correct order and check that the Power LED is on. 
4. If you have replaced the lamp recently, try resetting the lamp connections.  
5. Replace the lamp. 
6. Put the old lamp back in the projector and have the projector serviced. 
Problem: The lamp goes off 
1. Power surges can cause the lamp to turn off. Re-plug power cord. When the Power LED 
is on, press the power button. 
2. Replace the lamp. 
3. Put the old lamp back in the projector and have the projector serviced. 
Remote Control Problems 
Problem: The projector does not respond to the remote control  
1. Direct the remote control towards remote sensor on the projector.  
2. Ensure the path between remote and sensor is not obstructed. 
3. Turn off any fluorescent lights in the room. 
4. Check the battery polarity. 
5. Replace the battery. 
6. Turn off other Infrared-enabled devices in the vicinity. 
7. Have the remote control serviced. 
Audio Problems 
Problem: There is no sound 
1. Adjust the volume on the remote control.  
2. Adjust the volume of the audio source. 
3. Check the audio cable connection. 
4. Test the source audio output with other speakers. 
5. Have the projector serviced. 
Problem: The sound is distorted  
1. Check the audio cable connection. 
2. Test the source audio output with other speakers. 
3. Have the projector serviced. 
Having the Projector Serviced 
If you are unable to solve the problem, you should have the projector serviced. Pack the projector in 
the original carton. Include a description of the problem and a checklist of the steps you took when 
trying to fix the problem: The information may be useful to service personnel. For servicing, return 
the projector to the place you purchased it.  
						

							 — 60— 
SPECIFICATIONS 
Product Specifications 
Model name  LV-WX300UST/ LV-WX300USTi
Display system １chip DLP system
Optical system  Time division color extraction, sequential display 
Display device 
Display 
device 
Type DMD x1
Size / Aspect ratio 0.65type/16:10
Number dots 
(=Total number dots)  1,024,000 
Projection lens 
Projectio
n lens 
Operation 
Zoom: fixed, focus: manual
Focal length/ F 
number 5.1 mm / 2.5 
Throw ratio
0.35:1
Projection distance  60.5 - 70.5 cm
Lens shift 75%, fixed
Light source  230W Super-high pressure mercury lamp 
Image size  80 - 100type
Number of colors  16,770,000 (full color)
Brightness *1 3000lumen(inpresentation mode)
Contrast ratio *1 2300:1 (Fully white: fully black, presentation mode) 
Ratio of brightness at periphery 
to center *1  80% 
Speaker 
10W x2 (stereo)
Maximum input resolution 1600x1200
Image signal 
Image 
signal 
PC (analog) WXGA, UXGA, SXGA+, WXGA, SXGA, XGA, SVGA, VGA, Mac
PC (digital)UXGA, SXGA+, WXGA+, WXGA, SXGA, XGA, SVGA, VGA
Digital video 1080p, 1080i, 720p, 576p, 480p
Component video 1080p, 1080i, 720p, 576p, 576i, 480p, 480i 
Video / S video NTSC, PAL, SECAM, NTSC4.43, PAL-M, PAL-N, PAL-60
Audio signal  Impedance = 47ＫΩ or more
Terminal (Input/output/control) 
Input 
VGA in -1, 2Analog PC, component video (mini D-sub15 pin) 
HDMI -1, 2  Digital PC, digital video
S-VIDEO S video
VIDEO  Video
AUDIO IN（R,L） Audio input (2RCA)
AUDIO IN Audio input (3.5 φstereo mini jack)
Output VGA OUT  Monitor out (mini D-sub15 pin)
AUDIO OUTAudio output (3.5φstereo mini jack)
Control 
USB  USB Type B, mini USB (interactive used) 
RS-232 Serial connection
RJ45  Network connection
Noise level  33/29 dB
Operating temperature5°C - 40°C
Power supply AC100V - 240V, 50/60Hz
Power consumption  300W, 240W (Lamp mode: Full power, Power savor) 
Standby power consumption  6.0W, 0.5W (Network / RS232)
Dimensions LV-WX300UST  W: 287.5 mm ×H: 167.6 mm ×D: 374.5 mm 
（including the projection ）
LV-WX300USTi W: 287.5 mm 
×H: 193.7 mm  ×D: 374.5 mm（including the projection ）
Mass  5.0 kg
Accessories 
Remote control, battery for remote control, power code, VGA cable, User’s manual (CD-ROM), Important 
Information, Warranty Card 
Interactive software(CD-ROM) ,2In teractive Pens, battery for Interactive Pens, mini USB Cable 
*1 Compliance with ISO21118-2012  
						

							 
— 61— 
Installation Distance vs. Projection Size 
   
 
 
Installation Distance and Size Table  
 
WXGA 
16:10 
Diagonal 80 87 97 100 
Distance 282.3+/-20mm 340.3+/-20mm 421.4+/-20mm 445.8+/-20mm 
Image Width 1723mm 1874mm 2088mm 2154mm 
Image height 1077mm 1171mm 1305mm 1346mm 
H  280+/-50mm 300.2+/-50mm 325.5+/-50mm 336.9+/-50mm 
 
   
						

							 
— 62— 
Timing Mode Table 
The projector can display several resolutions. The following table outlines the resolutions that can 
be displayed by the projector. 
SIGNAL RESOLUTION 
HORIZONTAL 
FREQUENCY 
(KHZ) 
VERTICAL 
FREQUENCY 
(HZ) 
COMPOSITE COMPONENT ANALOG 
PC HDMI  
NTSC — 15.734 60.0 O — — — 
PAL/SECAM — 15.625 50.0 O — — — 
VESA 
720 x 400 37.9 85.04 — — O O 
640 x 480 31.5 60.0 — — O O 
640 x 480 37.9 72.8 — — O O 
640 x 480 37.5 75.0 — — O O 
640 x 480 43.3 85.0 — — O O 
800 x 600 35.2 56.3 — — O O 
* 800 x 600 37.9 60.3 — — O O 
800 x 600 46.9 75.0 — — O O 
800 x 600 48.1 72.2 — — O O 
800 x 600 53.7 85.1 — — O O 
** 800 x 600 76.3 120.0 — — O O 
1024 x 576 35.8 60.0 — — O O 
1024 x 600 37.3 60.0 — — O O 
1024 x 600 41.5 65.0 — — O O 
* 1024 x 768 48.4 60.0 — — O O 
1024 x 768 56.5 70.1 — — O O 
1024 x 768 60.0 75.0 — — O O 
1024 x 768 68.7 85.0 — — O O 
** 1024 x 768 97.6 120.0 — — O O 
1024 x 768 99.0 120.0 — — O O 
1152 x 864 67.5 75.0 — — O O 
* 1280 x 720 45.0 60.0 — — O O 
* 1280 x 720 90.0 120.0 — — O O 
1280 x 768 47.4 60.0 — — O O 
* 1280 x 768 47.8 59.9 — — O O 
* 1280 x 800 49.7 59.8 — — O O 
1280 x 800 62.8 74.9 — — O O 
1280 x 800 71.6 84.9 — — O O 
** 1280 x 800 101.6 119.9 — — O O 
*** 1280 x 1024 64.0 60.0 — — O O 
1280 x 1024 80.0 75.0 — — O O 
1280 x 1024 91.1 85.0 — — O O 
*** 1280 x 960 60.0 60.0 — — O O 
1280 x 960 85.9 85.0 — — O O 
**** 1280 x 1470 — 60.0 — — — O 
*** 1366 x 768 47.7 59.8 — — O O 
*** 1400 x 1050 65.3 60.0 — — O O 
1440 x 900 55.5 59.9 — — O O 
*** 1440 x 900 55.9 59.9 — — O O  
						

							 
— 63— 
SIGNAL RESOLUTION 
HORIZONTAL 
FREQUENCY 
(KHZ) 
VERTICAL 
FREQUENCY 
(HZ) 
COMPOSITE COMPONENT ANALOG 
PC HDMI  
1440 x 900 70.6 75.0 — — O O 
1600 x1200 75.0 60 — — O O 
1680 x 1050 64.7 59.9 — — O O 
1680 x 1050 65.3 60.0 — — O O 
1920 x 1200 74.0 60.0 — — O O 
1920 x 1080 67.5 60.0 — — O O 
**** 1920 x 2205 — 23.97 — — — O 
Apple  
Macintosh 
640 x 480 35.0 66.7 — — O O 
832 x 624 49.7 74.5 — — O O 
1024 x 768 60.2 74.9 — — O O 
1152 x 870 68.7 75.1 — — O O 
SDTV 480i 15.734 60.0 — O — O 
576i 15.625 50.0 — O — O 
EDTV 576p 31.3 50.0 — O — O 
480p 31.5 60.0 — O — O 
HDTV 
720p 37.5 50.0 — O — O 
720p 45.0 60.0 — O — O 
1080i 33.8 60.0 — O — O 
1080i 28.1 50.0 — O — O 
1080p 27 24 — O — O 
1080p 28 25 — O — O 
1080p 33.7 30 — O — O 
1080p 67.5 60.0 — O — O 
1080p 56.3 50.0 — O — O 
O: Frequency supported 
—: Frequency not supported 
3D note： 
“” It means the timing can support non-3D and 3D signal with Frame Sequential and Top-Bottom 
format. 
“”It means the timing can support non-3D and 3D signal with Frame Sequential format. 
“”It means the timing can support non-3D and 3D signal with Top-Bottom format. 
“”It means the timing can support 3D signal with Frame Packing format. 
There 3D timing showing depend the EDID file and display card. It is possible that user cannot 
choose the above 3D timings on display card. 
The resolution of the panel is 1280 x 800. Resolution other than native resolution may display with 
uneven size of text or lines.  
						

							 
— 64— 
Projector Dimensions(LV-WX300UST)