Canon projector LV8320 User Manual

VIDEO	Input
41
VIDEO	Input
Image	select	Menu
Image	Mode	Selection	
Remote	controller
IMAGE	button
Select the desired image mode among Presentation, Standard, High	contrast, Cinema, Blackboard	(Green), Colorboard, User 1, User 2, User 3 and User 4 by pressing the IMAGE button on the remote controller.
Standard
Picture mode with improved halftone for graphics.
High	contrast
Blackboard	(Green)
User	1-4
For the image projected on a blackboard.This mode helps enhance the image projected on a blackboard. This...

42
VIDEO	Input
Image	Adjustment
1
2
Press the Point ◄ button to decrease the contrast, press the Point ► button to increase the contrast (from 0 to 63).
Press the Point ◄ button to decrease the brightness, press  the Point ► button to increase the brightness (from 0 to 63).
Contrast
Brightness
Press the Point ◄ button to lighten R/G/B tone, press the Point ► button to deepen R/G/B tone (from 0 to 63).
White	balance	(Red	/	Green	/	Blue)
Use the Point ◄► buttons to select the desired Color temp. level...

VIDEO	Input
43
VIDEO	Input
An interlaced video signal can be displayed in progressive mode. Select one of the following options. Off ........  Disabled. L 1 ........  For an active picture. L 2 ........  For a still picture. Film .....  For watching a film. With this function, the projector reproduces pictures faithful to the original film quality.
Progressive
Noise	reduction
Noise interference on the screen can be reduced. Select one of the following options to get smoother images. Off ...........

44
VIDEO	Input
Aspect	Setting
This projector has the picture screen resize function, which enables you\
 to customize the image size.
Normal
Aspect	Menu1
2
Provide the image to fit the screen size while maintaining the aspect ratio of the input signal.
Custom	adj.
Note: • When no signal is detected, Normal	is set automatically and the Aspect adjustment menu disappears. • The adjustable range for Scale	H/V and Position	H/V is limited depending on the input signal.
Full
Provide the full screen image....

VIDEO	Input
45
VIDEO	Input
Keystone
This function is used to adjust keystone distortion of the  projected image. Use the Point ▲▼ buttons to choose the item you want to adjust. Keystone     
To correct keystone distortion, press the OK button.  Keystone appears on the screen. Use the Point ▲▼ buttons to correct keystone distortion (p. 25). Store		    
To store or reset the keystone correction, press the Point ► button.				Store .......... 
Keep the keystone correction even when the AC power cord is...

46
Setting
Setting	MenuPress the MENU button to display the On-Screen Menu. Press the Point ▲▼ buttons to select Setting and press the Point ► button or the OK button to access the submenu items.
1
2Use the Point ▲▼ buttons to select the desired item and then press the Point ► button or the OK button to access the selected item.
This projector has a Setting menu that allows you to set up the other va\
rious functions described below.
Language
Menu	position
This function is used to change the position of...

47
SettingSetting
Note:  • During Auto	input is in progress, If the MENU button or the POWER button is pressed, Auto	input will stop. If the COMPUTER 1/2 or VIDEO or COMPONENT or S-VIDEO or HDMI button is pressed, Auto	input will stop and go back to the button's input signal.   • Auto	input, Auto	PC and Auto	keystone can not be set Off at the same time.    • Auto	keystone corrects vertical distortion only, not correct horizontal distortion.  • The Auto keystone function can not work when the Ceiling...

48
Setting
This function decides whether to display On-Screen Displays. On ........................  Show all the On-Screen displays. Use this function when you want to project images after the lamp becomes bright enough. The factory default setting is in this option. Countdown	off ...  Show the input image instead of the countdown when turning on the projector. Use this function when you want to project the image as early as possible even when the lamp is not bright enough. Off ...........................

Setting
49
Setting
Capture
Capture
This function enables you to capture an image being projected to use it for a starting-up display or interval of presentations.
Select Capture and press the OK button.  A confirmation box appears and select Yes to capture the projected image.
After capturing the projected image, go to the Logo select function and set it to User. Then the captured image will be displayed the next time you turn on the projector or when you press the BLANK button (p. 28). 
To cancel the...

50
Setting
Enter	a	Logo	PIN	codeUse the Point ▲▼ buttons to enter a number. Press the Point ◄► buttons to fix the number and move the red frame pointer to the next box. The number changes to . If you fixed an incorrect number, use the Point ◄► buttons to move the pointer to the number you want to correct, and then enter the correct number.
Repeat this step to complete entering a four-digit number.
After entering the four-digit number, move the pointer to Set. Press the OK button so that you can start to...