Canon projector LV7585 User Manual

							
51

Lamp mode
Filter control
Choose the running speed of cooling fans from the following 
options.
 Normal  .......  Operate in this mode under normal conditions.
  Max  ...........  Use this mode when you want to increase the 
cooling effect when operating the projector in high 
ambient temperature environment. Fan noise is 
lounder than “Normal”. 
Fan control
Remote control
Remote control
When pressing the OK button at Remote control unit, the Remote control code menu appears.
RC sensor
Select a location of the infrared remote receiver of the remote 
control unit. See “Remote Control Receivers and Operating Range” 
on page 15 for details.
  Both  .........  Activate both the front and back receiver.
  Front  ........  Activate only the front receiver.
  Back  .........  Activate only the back receiver.
The eight different remote control codes (Code 1–Code 8) are 
assigned to the projector; the factory-set, initial code (Code 1) and 
the other seven codes (Code 2 to Code 8). 
The same code should set on both the projector and the remote 
control unit. For example, operating the projector in “Code 7”, the 
remote control code also must be switched to “Code 7”.
 To change the code for the projector
  Select a remote control code in this Setting Menu.
 To change the code for the remote control unit:
  Press and hold the MENU button and a number button (1–8) on  
  the remote control unit for more than 5 seconds to switch    
  between the codes (p. 16).
This function allows you to change the brightness of the screen.
You can replace the filter with this function. Press the OK button at 
Filter control to display a confirmation box. To replace, press the OK 
button at “YES” and the electrically operated filter starts to scroll.
You can also replace the filter by using the remote control unit (p. 
29). 
Setting
✔Note:
	 •	Filter	replacement	icon	and	 “Please	wait...”	
message	appear	on	the	screen	when	the	
filter	is	being	scrolled.
	•	When	the	filter	is	replaced,	 the	total	
accumulated	time	of	the	filter	use 	is	
automatically	set	to	0
.
 Auto mode . . . . . . Brightness according to the input signal.
 Normal mode. . . . Normal brightness.
 Eco 1 mode  . . . . . Lower brightness and Fan control set to 
Normal. Lower brightness reduces the 
lamp power consumption and extends the 
lamp life.
 Eco 2 mode  . . . . . Lower brightness and Fan control set to 
Max. Lower brightness reduces the lamp 
power consumption and extends the lamp 
life. It is recommended to use Eco 2 mode 
when using the projector continuously 
over a long period of time. The fan noise 
becomes louder in Ecot 2 mode than in 
Eco 1 mode. Select the suitalbe mode for 
the used environment.  
						

							
5

On start
When this function is set to “On,” the projector will be 
automatically turned on just by connecting the AC power cord to 
the wall outlet.
✔Note:
	 •	 Be	sure	to	turn	off	the	projector	properly	(see	“Turning	Off	the	
Projector”	on	page	24).	If	the	projector	is	turned	off	in	the	incorrect	
sequence,	the	On	start	function	does	not	work	properly.
Power management
Time left before the lamp is off
Press the OK button at Power management and the dialog box appears.  Use the Point 7 8 buttons to choose one of the three options.Press the Point d button to select the timer, and then use the Point 7 8 buttons to set the timer
For reducing power consumption as well as maintaining the lamp 
life, the Power management function turns off the projection lamp 
when the projector is not used for a certain period.
If the input signal is interrupted and no button is pressed for more 
than 30 seconds, the timer display with “No signal” appears. It 
starts the countdown until the lamp is turned off. The countdown 
time can be set between 1 and 30 minutes.
Use the Point 7 8 buttons to set the countdown timer.
Select one of the following options:
  Ready 
  . . . .  When the lamp has been fully cooled down, the 
POWER indicator starts blinking. In this condition, 
the projection lamp is turned on if the input signal 
is reconnected or any button on the side control or 
remote control unit is pressed . 
  Shutdown
. .  When the lamp has been fully cooled down, the 
power is turned off. 
  Off 
. . . . . . .  Power Management function is off. 
Power management
The Projector has a USB port for interactive operation between 
the projector and computers. Set the mode by following the steps 
below.
Wireless Mouse mode
Select “” when controlling a computer with the remote control 
unit of this projector.
Projector mode:
“” Not used.
USB
Pointer
You can emphasize a part of the projected image with this function. 
Use the Point 7 8 buttons to select a pattern of the Pointer (Arrow, 
Cross, or Dot) (P. 30)
✔Note:
	 •	 Factory	default	is	 “Ready:	5	min.”
Setting
✔Note:
	 •	 The	Point	ed7 8 buttons	and	OK	button	are	invalid	when	the	
Pointer	function	is	operating. 
						

							
5

Security
Key lock
Key lock
Security
Select Key lock and this box appears. Choose one of the alternatives with the Point ed buttons and select [Yes] to activate it.
This function locks the side control and remote control buttons to 
prevent operation by unauthorized persons.
. . . . . Unlocked.
. . . . .  Lock the side control buttons.
  To unlock, use the remote control unit.
. . . . . Lock the remote control buttons.  
To unlock, use the side control.
If the side control accidentally becomes locked and you 
do not have the remote control unit nearby and unable to 
operate the projector, contact the service station. 
PIN code lock
This function prevents the projector from being operated by 
unauthorized persons and provides the following setting options  
for security.
  Off
  . . . .  Unlocked.
  On1
  . . .  Enter the PIN code every time turning on the projector.  
  On2
  . . .  Enter the PIN code to operate the projector once the 
power cord is disconnected; as long as the AC power 
cord is connected, the projector can be operated 
without a PIN code.
Whenever you change the PIN code lock setting or the PIN code 
(the four-digit number), you are required to enter the PIN code. 
“1234” is set as the initial PIN code at the factory.
If you want to change the PIN code lock setting, press the OK 
button and the PIN code dialog box appears. Enter a PIN code by 
following the steps on the next page.
PIN code lock
When the projector is locked with a PIN code, the PIN code lock symbol appears on the menu bar. 
Set the red frame pointer to the item and press the OK button.
Setting 
						

							
54

Change the PIN Code 
Change the PIN code
CAUTION:
WHEN y OU HAVE CHANGED THE PIN CODE,  WRITE DOWN 
A NEW PIN CODE IN COLUMN OF  THE PIN CODE NO . MEMO 
ON PAGE 76,  AND KEEP IT SECUREL y . IF y OU FORGET y OUR 
PIN CODE,  THE PROjECTOR CAN NO LONGER BE STARTED .
The PIN code can be changed to your desired four-digit number. 
Press the Point d buttons to select “PIN code change” and press 
the OK button. The New PIN code input dialog box appears. Set a 
new PIN code.
Lamp counter
This function is used to reset the lamp counter. 
When the lamp life reaches a recommended lamp replacement 
time, the time shown in the dialog box turns red and the Lamp 
replacement icon appears on the screen, indicating that the end of 
lamp life is approaching.
When replacing the projection lamp, reset the lamp counter. See 
“Resetting the Lamp Counter” on page 60.
This icon appears on the screen when the end of lamp life is approaching.
✔Note:
	•	 This	icon	also	appears	at	turning	on	and	
selecting	input	source.
✔Note:	 •	 The	Lamp	replacement	icon	will	not	appear	when	the	Display	 function	is	set	to	 “Off”	(p.48),	during	 “Freeze”	(p.28),	or	“Blank”	
(p.29).
Change the PIN Code Lock setting
Change the PIN code lock setting
Use the Point 7 8 buttons to switch between the options.
Enter a PIN code
Use the Point 7 8 button to select Off, On1, or On2 and then 
move the pointer to “Quit” with the Point d button. Press the OK 
button to close the dialog box.
After a correct Logo PIN code is entered, the following dialog box appears.
Enter a PIN codeUse the Point ed buttons on the side control or Number buttons 
on the remote control unit to enter a number. 
When using side control
Use the Point ed buttons on the side control to select a number. 
Press the Point 8 button to fix the number and move the red 
frame pointer to the next box. The number changes to “✳.” 
Repeat this step to complete entering a four-digit number. After 
entering the four-digit number, move the pointer to “Set.” Press 
the OK button so that you can change the PIN code lock setting.
When using remote control unit
Press the Number buttons on the remote control unit to enter a 
number (p.14). When you complete entering a four-digit number, 
the pointer moves to “Set.” Press the OK button so that you can 
change the PIN code lock setting.
 If you fixed an incorrect number, use the Point 7 button to move 
the pointer to the number you want to correct, and then enter the 
correct number.
If you entered an incorrect PIN code, “PIN code” and the number 
(✳✳✳✳) will turn red for a moment. Enter the correct PIN code all 
over again.
Setting
NOTE: 
If  you  forget  your  PIN  code  and  unable  to  change 
it,  the  PIN  code  can  be  reset  to  the  factory  default setting (1234) according to the following procedures.When you reset the PIN code, the Logo PIN code and Key lock will be reset, as well.
1. Unplug the AC Power Cord from the AC outlet.
2.  Hold  down  the  OK  button  on  the  projector  and 
connect  the  AC  Power  Cord  into  the  outlet  again. Keep holding down the OK button until the POWER indicator  lights. The  PIN  code  returns  to  the  factory default  setting  while  the  PIN  code  lock  state  will remain the same as the previous set state. 
						

							
55

Factory default
This function returns all setting values except for the user logo, PIN 
code lock, Logo PIN code lock, lamp counter, and filter counter to 
the factory default settings.
Factory default
Quit
Exit the Setting Menu.
Select Factory default and this box appears. Select [Yes], and the next box appears. 
Test pattern
Various test pattern are available for use when setting up the 
projector.
Filter counterFilter counter
Filter replacement icon appears on the screen at a set time.
✔Note:	 •	 Do	not	reset	the	counter(s)	when	the	filter	or	the	filter	cartridge	are	not	replaced.
	 •	 Timer	setting	notifies	that	the	filter	needs	replacement.	 To	replace	
the	filter,	use	the	filter	control	function	(p.51).
Fig .1   Filter replacement icon
Filter cartridge replacement icon appears on the screen when the filter scroll is counted down to 0 scroll.
Fig .4   Filter cartridge replacement icon
✔Note:
	•	 Fig.1,	Fig.	2,	Fig.	3	and	Fig.	4	appear	at	turning	 on	and	selecting	input	source.
	 •	 Fig.1,	Fig.	2,	Fig.	3	and	Fig.	4	will	not	appear	 when	the	Display	function	is	set	to	 “Off”	(p.48),	
during	 “Freeze”	(p.28),	or	 “Blank”	(p.29).
Set the red frame pointer to the item and press the OK button.
Set the red frame pointer to the item and press the OK button.
Last scroll icon appears on the screen when the filter is down to the last scroll.
Fig .   Last scroll icon
Use the Point 7 8 buttons 
to set the timer. Select from 
(Off/ 400H/700H/1000H) 
depending on the use 
environment.
Setting
This function is used to set a frequency for the filter replacement.
Use the Point ed buttons to move the red frame pointer to 
Filter counter and then press the OK button. A dialog box appears 
showing the Used time option and the Scrolls remaining option. 
 Used Time
  . . . . . .  Show the total accumulated time of the 
filter use, timer setting option and the Reset 
options. When the projector reaches a time 
set in the timer setting, the Filter replacement 
icon (Fig. 1) appears on the screen and the 
total accumulated time turns red, indicating 
that the filter replacement is necessary. If 
the filter is out of scroll and the projector 
reaches a time set in the timer setting, Fig. 
2 appears on the screen, indicating that the 
filter cartridge replacement is necessary.
 Scrolls remaining. .  Show the scroll counter and the Reset 
options. When the filter scroll is counted 
down to 1 (Scroll counter on the screen is 
showing “0 scroll(s)” , the last scroll icon 
(Fig. 3) appears on the screen. When the 
filter scroll is counted down to 0, the Filter 
cartridge replacement icon (Fig. 4) appears 
on the screen and the WARNING FILTER 
indicator lights orange, indicating that the 
filter cartridge replacement is necessary.
To set a timer, press the OK button on Used time option. Move the 
red arrow pointer to the timer setting option and use the Point 7 8 
buttons to select from (Off/ 400H/700H/1000H) depending on the 
use environment.
When replacing the Filter cartridge, reset the Filter counter and the 
Scroll counter (p.58).
Select [Yes] to activate it.
Fig . 
						

							
56

Filter Instructions
Filter prevents dust from accumulating on the optical elements inside the projector\
. Should the filter becomes 
clogged with dust particles, it will reduce cooling fans’ effectiveness and may result in internal heat buildup 
and adversely affect the life of the projector. This projector has an electrically operated filter which helps you to 
replace the filter easily. The projector monitors the condition of the filter at all time and replac\
es a filter with a 
new one automatically when it detects the clogging. 
If the projector reaches a time set in the timer setting (p. 
55), a Filter replacement icon (Fig.1) appears on the screen 
and the WARNING FILTER indicator on the top panel lights 
up (p.70). When you see this icon, replace the filter as soon 
as possible (pp.29, 51). If the filter is out of scroll and the 
projector reaches a time set in the timer setting, Fig. 2 
appears on the screen, indicating that the filter cartridge 
replacement is necessary.
When the filter scroll is counted down to 1, the Last scroll 
icon (Fig.3) appears on the screen, indicating that there is 
one scroll left in the filter cartridge (p.55).
If the projector detects that the filter is clogged and no scroll 
is left in the filter cartridge, a Filter cartridge replacement 
icon (Fig. 4) appears on the screen and the WARNING 
FILTER indicator on the top panel lights up (p.70). When you 
see this icon, replace the filter cartridge (p.57) and reset the 
Filter counter (p.58) and the Scroll counter (p.58).
When the filter is being scrolled using the remote control 
unit (p.29) or the Filter control function in the setting 
menu (p.51), a Filter replacement icon and “Please wait...” 
message (Fig.5) appear on the screen and the WARNING 
FILTER indicator blinks slow (approx. 2 seconds ON, 2 
seconds OFF) (p.69).
The WARNING FILTER indicator blinks fast when the 
projector detects an abnormal condition, the filter cartridge 
is not installed properly, or the filter scroll is not working 
properly (p.70).
Fig .1   Filter replacement icon
Fig .4    Filter cartridge replacement icon
Fig .
   Last scroll icon
Maintenance and Care
✔Note:
	 •	 Fig.1,	Fig.2,	Fig.3,	Fig.	4	and	Fig.5	will	not	appear	when	the	
Display	 function	 is	set	 to	“Off”	 (p.48),	 during	 “Freeze”	 (p.28),	
or	 “Blank”	(p.29).
	 •	 The	filter	cannot	be	rewinded.
	 •	 The	filter	can	be	scrolled	9	times	since	the	filter	cartridge	 has	10	scrolls.	
	 •	 The	filter	cartridge	is	disposable.	Do	not	clean	and	reuse	the	 filter	cartridge.
	 •	 Do	not	expose	the	filter	cartridge	to	water	or	liquid,	or	it	 may	cause	a	breakdown.
	 •	 Replace	the	filter	cartridge	after	all	the	scroll	is	used	up.	If	 you	replace	the	filter	cartridge	when	there	are	some	scrolls	
left	in	the	filter	cartridge,	the	filter	counter	and	the	scroll	
counter	do	not		recognize	the	correct	number	of	remaining	
scrolls	and	the	reset	function	cannot	work	properly.	It	may	
cause	a	breakdown.
Fig .5    Filter replacement icon and 
“Please wait...” message. 
	 •	 Do	not	use	the	filter	cartridge	with	other	projector.	 The	filter	
counter	and	the	scroll	counter	do	not	recognize	the	correct	
number	of	remaining	scrolls	of	the	used	filter	cartridge	and	
the	reset	function	cannot	work	properly.	It	may	cause	a	
breakdown.
	 •	 Make	sure	that	the	projection	lamp	is	turn	off	when	you	 are	replacing	the	filter	cartridge.	If	you	replace	the	filter	
cartridge		when	the	projection	lamp	is	turn	on,	the	projector	
will	be	shut	down	automatically	for	safety	purpose
	 •	 When	you	forget	to	reset	the	filter	counter,	the	projector	 cannot	recognize	the	correct	number	of	remaining	scrolls	
and	may	cause	a	breakdown.	
	 •	 Do	not	forget	to	reset	the	filter	counter	and	the	scroll	 counter	in	the	setting	menu	after	replacing	the	filter	
cartridge.	If	you	forget	to	reset	the	filter	counter	and	the	
scroll	counter,	the	projector	cannot	recognize	the	correct	
number	of	remaining	scrolls	and	may	cause	a	breakdown.	
Fig . 
						

							
57

Turn off the projector, and unplug the AC power cord 
from the AC outlet.
First, clean up the dust on the projector and around the 
air vents.
1
2
Press s on the filter cover to release the latch and open 
the filter cover.3
Put the new one back into the position and close 
the filter cover. Make sure that the filter cartridge is 
properly and fully inserted.
5
CAUTION
Make sure the filter cartridge is inserted in the 
projector. If the filter cartridge is not inserted, the 
projector cannot be turned on. 
Do not put anything into the air vents. Doing so 
may result in malfunction of the projector.
4
Reset the filter counter and the scroll counter (p.58).
6
Filter cover
Replacing the Filter Cartridge
Pull out the filter cartridge. When taking out the filter 
cartridge, put your finger on the filter cartridge’s tab 
and then pull.Latch
Filter cartridgeTab
RECOMMENDATION
We recommend avoiding dusty/smoky environments when 
operating the projector . Usage in these environments may 
cause a poor image quality  .
When using the projector under dusty or smoky conditions, 
dust may accumulate on a lens, liquid crystal panels, or optical 
elements inside the projector. Such condition may degrade the 
quality of the projected image.
When the symptoms above are noticed, contact your authorized 
dealer or service station for proper cleaning.
Connect  the  AC  power  cord  to  the  projector  and  turn 
on the projector.
7
Maintenance and Care 
						

							
58

Be sure to reset the Scroll counter after replacing the filter 
cartridge. 
Press the MENU button to display the On-Screen Menu. Use 
the Point 7 8 buttons to move the red frame pointer to the 
Setting Menu icon.
Use the Point ed buttons to move the red frame pointer 
to Filter counter and then press the OK button. A dialog 
box appears showing the Used time option and the Scrolls 
remaining option. Use the Point ed buttons to select  
Scroll(s) remaining.
1
2
Resetting the Scroll CounterScroll counter
Another confirmation dialog box appears, select [Yes] to 
reset the Scroll counter.
3Scroll(s) remaining shows the number of the remaining 
scrolls and the Reset option. Select Reset and the “Scroll 
counter Reset?” appears. Select [Yes] to continue.
4
Be sure to reset the Filter counter after replacing the filter 
cartridge. 
Press the MENU button to display the On-Screen Menu. Use 
the Point 7 8 buttons to move the red frame pointer to the 
Setting Menu icon.
Use the Point ed buttons to move the red frame pointer 
to Filter counter and then press the OK button. A dialog 
box appears showing the Used time option and the Scrolls 
remaining option. Use the Point ed buttons to select  Used 
time.
1
2
Resetting the Filter CounterFilter counter
Select Reset and the “Filter 
counter Reset?” appears.
Select [Yes], 
then another 
confirmation 
box appears.
Select [Yes] again to reset 
the Filter counter.
Another confirmation dialog box appears, select [Yes] to 
reset the Filter counter.
3Used time shows the total accumulated time of the filter 
use, a timer setting option, and the Reset option. Select 
Reset and the “Filter counter Reset?” appears. Select [Yes] 
to continue.
4
Select “Scrolls remaining” and 
the dialogue box below appears.
Select Reset and the “Scroll 
counter Reset?” appears.
Select [Yes], 
then another 
confirmation 
box appears.
Select [Yes] again to reset 
the Scroll counter.
Maintenance and Care
Select “Used time” and the 
dialogue box below appears. 
						

							
59

Turn off the projector and unplug the AC power cord. Let 
the projector cool for at least 45 minutes.
Loosen the screw and open the lamp cover. Pull out the 
lamp by using the built in handle.
1
3
Replace the lamp with a new one. Make sure that the 
lamp is properly and fully inserted. 4
Open the filter cover. (p.57)2
Connect the AC power cord to the projector and turn on 
the projector.
6
Follow these steps to replace the lamp.
Reset the Lamp counter (p.60)
5
✔Note:
	 •	 Be	sure	to	insert	the	lamp	in	the	correct	direction.
	 •	 Do	not	reset	the	Lamp	counter	when	the	projection	lamp	is	not	replaced.
Lamp Replacement
For continued safety, replace with a lamp  of the 
same type. Do not drop the lamp or touch the 
glass bulb! The glass can shatter and may cause 
injury.
Allow a projector to cool for at least 45 minutes 
before you open the lamp cover. The inside of the 
projector can become very hot.
CAUTIONCAUTION
When the projection lamp of the projector reaches its end of life, the Lamp replacement icon appears on the 
screen and LAMP REPLACE indicator lights orange. Replace the lamp with a new one promptly. The timing 
when the LAMP REPLACE indicator should light is depending on the lamp mode.
Top Panel
LAMP REPLACE indicator
Lamp replacement icon
✔Note:	 •	 The	Lamp	replacement	icon	will	not	appear	when	the	Display	function	is	set	to	 “Off”	(p.48),	during	
“Freeze”	(p.28),	or	 “Blank”	(p.29).
7
Close the lamp cover and secure the screw. 
LampHandle
Lamp coverFilter cover
Screw
Maintenance and Care
8
Close the filter cover. 
						

							
60

ORDER REPLACEMENT LAMP
Replacement lamp can be ordered through your dealer. When ordering, give the following information to the 
dealer.
 ●  Model No . of your projector  :  LV-7585
 ●  Replacement Lamp Type No  . :  LV-LP9 
Resetting the Lamp Counter
Be  sure  to  reset  the  Lamp  counter  after  the  lamp  is  replaced.  When  the  Lamp  counter  is  reset,  the  LAMP 
REPLACE indicator stops lighting and the Lamp replacement icon disappears.
✔Note:
	 •	 Do	not	reset	the	Lamp	counter	without	replacing	the	lamp.	Be	sure	
to	reset	the	Lamp	counter	only	after	replacing	the	lamp.
Press the MENU button to display the On-Screen Menu. Use 
the Point 7 8 buttons to move the red frame pointer to the 
Setting Menu icon 
Use the Point ed buttons to move the red frame pointer to 
Lamp counter and then press the OK button. A dialog box 
appears showing the total accumulated time of the lamp 
usage and the reset option. Select Reset and the “Lamp 
replacement coutner Reset?” appears. Select [Yes] to 
continue.
1
2
Lamp counter
Select Reset and the “Lamp replacement counter Reset?” appears.
Select [Yes] again to reset the lamp counter.
Select [Yes],  then another confirmation box appears.
Another confirmation dialog box appears and select [Yes] to 
reset the Lamp counter.3
Maintenance and Care