Canon projector LV7575 User Manual

11
PREPARATION
CAUTION IN CARRYING OR TRANSPORTING A PROJECTOR
●Do not drop or bump the projector, otherwise damages or malfunctions may\
 result.
● When carrying the projector, use a suitable carrying case.
● Do not transport the projector by courier or any other transport service\
 in an unsuitable transport case.
This may cause damage to the projector. To transport the projector by co\
urier or any other transport
service, consult your dealer for the best way.
MOVING PROJECTOR
Use the Carrying Handle...

12
CONNECTING PROJECTOR
S–VIDEO
R–AUDIO–L
VIDEO/Y Cb/Pb    Cr/Pr VIDEO/Y Cb/Pb Cr/Pr
RESETCONTROL PORT AUDIO 2
RGB ANALOG IN/OUT
RGB DIGITAL
INPUT 1
INPUT 2
INPUT 3
R/C JACK
GB R H/V V
(
MONO )
AUDIO 1
IN/OUT
TERMINALS OF PROJECTOR
When controlling a computer
with the remote control unit
of this projector, connect the
mouse port of your personal
computer to this connector.
(See page 13.)
Connect S-VIDEO output
from video equipment to
this jack. (See page 14.)Connect an audio output
from video equipment...

13
CONNECTING PROJECTOR
S–VIDEO
R–AUDIO–L
VIDEO/Y Cb/Pb    Cr/Pr VIDEO/Y Cb/Pb Cr/Pr
RESETCONTROL PORT AUDIO 1
AUDIO 2
RGB ANALOG IN/OUT
RGB DIGITAL
INPUT 1
INPUT 2
INPUT 3R/C JACK
GB RH /V V
(
MONO )
IN/OUT
CONNECTING TO COMPUTERS
IBM-compatible computer or Macintosh computer (VGA/SVGA/XGA/SXGA/SXGA+/\
WXGA/UXGA )
VGA Cable
Monitor Output
Desktop type Laptop type
Control Cable
for Serial Port 
Terminal
Serial port PS/2 port
Audio Output
CONTROLPORT
COMPUTER
AUDIO IN 1 or 2
RGB ANALOG IN/OUT
Use one of...

14
CONNECTING PROJECTOR
CONNECTING TO VIDEO EQUIPMENT
S–VIDEO
R–AUDIO–L
VIDEO/Y Cb/Pb    Cr/Pr VIDEO/Y Cb/Pb Cr/Pr
RESETCONTROL PORT AUDIO 1
AUDIO 2
RGB ANALOG IN/OUT
RGB DIGITAL
INPUT 1
INPUT 2
INPUT 3R/C JACK
GB RH /V V
(
MONO )
IN/OUT
Video Source (Example)
Video Cassette Recorder Video Disc Player
S-VIDEO
Cable ✽
Terminals 
of the Projector
S-VIDEO Output
Cables used for connection(✽= Cables not supplied with this projector.)
Audio Cable
(RCA x 2)  ✽
AUDIO IN S-VIDEO
Y - Cb/Pb - Cr/Pr
VIDEO Component...

15
BEFORE OPERATION
FOCUS BUTTON
Used to adjust focus. (p.22)
AUTO PC ADJ. BUTTON
Use to operate the AUTO PC
Adjustment function. (p.26)
KEYSTONE BUTTON
Used to correct keystone
distortion. (pp.22, 38)
IMAGE BUTTON
Used to select the image
level. (pp.29, 33)
REMOTE CONTROL OPERATION
ALL OFF SWITCH
Left Side
When using the remote control unit,
turn this switch to “ON.” And turn it
to “ALL OFF” when it is not in use.
This remote control unit emits laser beam from the Laser Light Window wh\
en used as a...

16
BEFORE OPERATION
To insure safe operation, please observe following precautions:● Use two (2) AA or LR6 type alkaline batteries.
● Always replace batteries in sets.
● Do not use a new battery with an used battery.
● Avoid contact with water or liquid.
● Do not expose the remote control unit to moisture, or heat.
● Do not drop the remote control unit.
● If a battery has leaked on the remote control unit, carefully wipe the c\
ase clean and install new batteries.
● Danger of explosion if battery is...

17
BEFORE OPERATION
TOP CONTROLS AND INDICATORS
Used to open or
close the On-Screen
Menu. (p.18, 19)
MENU BUTTON
LAMP MODE BUTTON
READY INDICATOR
OK BUTTON
POWER BUTTON
INPUT BUTTON
WARNING TEMP. INDICATOR
LAMP INDICATOR
POINT (VOLUME + / – ) BUTTONS 
LAMP REPLACE INDICATOR
Used to select a Lamp
mode. (p.41)
Lights green when the
projector is ready to be
turned on. And it blinks
green in the Power
management mode. 
(pp.40, 46, 56–57)
Becomes dim when the
projector is turned on.
And it becomes bright
when...

18
BEFORE OPERATION
HOW TO OPERATE ON-SCREEN MENU
You can control and adjust this projector with On-Screen
Menu. Refer to the relevant pages to operate each
adjustment.
2. MOVING POINTER
3. SELECT ITEM
Move the pointer (✽see below) or adjust a value of an
item by pressing the POINT buttons on the top control
or on the remote control unit.
Select an item or set the selected function by pressing
the OK button.
ON-SCREEN MENU
✽ The Pointer is an icon in the On-Screen Menu for selecting
an item. See figures...

19
BEFORE OPERATION
MENU BAR
FOR PC SOURCEPress the MENU button when connecting to the PC input source.
FOR VIDEO SOURCEPress the MENU button when connecting to the VIDEO input source.
Same function as
menu for PC source.
Same function as
menu for PC source.
GUIDE WINDOW
Shows the
selected item of
On-Screen Menu.
PC SYSTEM MENU
Used to select a
computer system.
(See pages 24–25.)
IMAGE SELECT MENU
Used to select an
image level among
Standard, High
contrast, and Custom
1–10. (See page 29.)
SCREEN MENU...

20
BASIC OPERATION
TURNING ON THE PROJECTOR
TURNING ON / OFF PROJECTOR 
Connect the projector’s AC power cord into an AC
outlet. The LAMP indicator lights RED, and the READY
indicator lights GREEN.
Press the POWER button on the top control or on the
remote control unit. The LAMP indicator dims, and the
cooling fans start to operate. The preparation display
appears on the screen and the countdown starts. 
2
3
130
The preparation display disappears after 30 seconds.
4After the countdown, the input source...