Canon projector LV7355 User Manual

							31
VIDEO INPUT
AV SYSTEM MENU (VIDEO OR S-VIDEO)
AV SYSTEM MENU (COMPONENT VIDEO)
SELECTING VIDEO SYSTEM
Press MENU button and ON-SCREEN MENU will appear.  Press
POINT LEFT/RIGHT buttons to move a red frame pointer to AV
SYSTEM Menu icon.
Press POINT DOWN button to move a red arrow pointer to the
system that you want to select and then press SET button.
1
2
If projector cannot reproduce proper video image, it is necessary to
select a specific broadcast signal format among PAL, SECAM, NTSC,
NTSC 4.43, PAL-M, and PAL-N.
Move the pointer to the
system and press SET
button.
PAL / SECAM / NTSC / NTSC4.43 / PAL-M / PAL-N
Projector automatically detects incoming Video signal, and adjusts
itself to optimize its performance.
If projector cannot reproduce proper video image, it is necessary to
select a specific component video signal format among 480i, 575i,
480p, 575p, 720p, 1035i and 1080i.
Auto
COMPONENT VIDEO SIGNAL FORMAT
VIDEO (Y) JACK OR S-VIDEO JACK
Y, Pb/Cb, Pr/Cr JACKS
Projector automatically detects incoming Video system, and adjusts
itself to optimize its performance.
When Video System is PAL-M or PAL-N, select system manually.
Auto
AV SYSTEM Menu icon
This box indicates the system
being selected.
Move the pointer to the
system and press SET
button.AV SYSTEM Menu icon
This box indicates the system
being selected. 
						

							32
VIDEO INPUT
PICTURE IMAGE ADJUSTMENT
IMAGE LEVEL SELECT (MENU)
Press MENU button and ON-SCREEN MENU will appear.  Press
POINT LEFT/RIGHT button to move a red frame pointer to
IMAGE SELECT Menu icon.1
2Press POINT DOWN button to move a red frame pointer to the
level that you want to set and then press SET button.
Move the red frame pointer to the
level and press SET button.
The level being selected.
IMAGE SELECT MENU
Normal picture level preset on this projector.
Standard
Picture level adjusted for the picture with fine tone.
Cinema
User preset picture adjustment in IMAGE ADJUST Menu (P33, 34).
Custom
IMAGE SELECT
Menu icon
IMAGE LEVEL SELECT (DIRECT)
Select image level among Standard, Cinema, and Custom by pressing
IMAGE button on  Remote Control Unit.
Normal picture level preset on this projector.  
Standard
Picture level adjusted for the picture with fine tone.
Cinema
User preset picture adjustment in IMAGE ADJUST Menu (P33, 34).
Custom
IMAGE button
Standard
Cinema
Custom 
						

							33
VIDEO INPUT
Press POINT LEFT/RIGHT buttons
to adjust value.
Press MENU button and ON-SCREEN MENU will appear.  Press
POINT LEFT/RIGHT button(s) to move a red frame pointer to
IMAGE ADJUST Menu icon.1
2Press POINT DOWN button to move a red frame pointer to the
item that you want to adjust and then press SET button.  The
level of each item is displayed.  Adjust each level by pressing
POINT LEFT/RIGHT button(s).
Move the red frame pointer to
the item to be selected and
then press SET button.
IMAGE ADJUST MENU
IMAGE LEVEL ADJUSTMENT
Press POINT LEFT button to decrease contrast, and POINT RIGHT
button to increase contrast.  (From 0 to 63.)
Press POINT LEFT button to adjust image darker, and POINT
RIGHT button to adjust brighter.  (From 0 to 63.)
Contrast
Brightness
Press either POINT LEFT button or POINT RIGHT button to obtain
better balance of contrast.  (From 0 to 15.)
Gamma
Press SET button at this icon to dis-
play other items.
IMAGE ADJUST
Menu icon
Press POINT LEFT/RIGHT buttons
to adjust value.
Press POINT LEFT button to lighten color, and POINT RIGHT button
to deeper color.  (From 0 to 63.)
Press POINT LEFT button or POINT RIGHT button to obtain proper
color.  (From 0 to 63.)
Color
Tint
Press POINT LEFT button to soften the image, and POINT RIGHT
button to sharpen the image.  (From 0 to 31.)
Sharpness
Press POINT LEFT button to lighten red tone and POINT RIGHT
button to deeper tone.  (From 0 to 63.)
White balance (Red)
Press POINT LEFT button to lighten green tone and POINT RIGHT
button to deeper tone.  (From 0 to 63.)
White balance (Green)
Press POINT LEFT button to lighten blue tone and POINT RIGHT
button to deeper tone.  (From 0 to 63.)
White balance (Blue)
NOTE : Tint cannot be adjusted when the video system is PAL,
SECAM, PAL-M or PAL-N.
Press SET button at this icon to
store the value.
Press SET button at this icon to dis-
play previous items. 
						

							34
VIDEO INPUT
PICTURE SCREEN ADJUSTMENT
This projector has a picture screen resize function, which enables you to display the desirable image size.
Press MENU button and ON-SCREEN MENU will appear.  Press
POINT LEFT/RIGHT button(s) to move a red frame pointer to
SCREEN Menu icon.
Press POINT DOWN button and move a red frame pointer to the
function that you want to select and then press SET button.
1
2
NOTE : SCREEN Menu cannot be operated when
“720p,” “1035i,” or “1080i” is selected on AV
SYSTEM Menu (P30).
Move the red frame to the function and
press SET button.
SCREEN MENU
SCREEN Menu icon
Provides image at a wide screen ratio of 16 : 9.
Wide
Provides image at a normal video aspect ratio of 4 : 3.
Normal
3
To store manually preset image level, move a red frame pointer
to Store icon and press SET button.  The message “OK?” will
appear.  Select [Yes] to store manual adjustment.
To set this manual adjustment, select Custom by pressing
IMAGE button or through IMAGE SELECT MENU (refer to P32).
Store icon
Reset all adjustment to previous figure.
Reset
Store
Closes IMAGE MENU.
Quit
Other icons operate as follows.
“OK?” message
Move the red arrow
pointer to [Yes] and
then press SET button. 
						

							35
SETTING
Ceiling
When this function is “On,” the picture is top / bottom and left / right
reversed.  This function is used to project the image from a ceiling
mounted projector.
Rear
When this function is “On,” the picture is left / right reversed.  This
function is used to project the image to a rear projection screen.
Ceiling function
Rear function
Keystone
When the image is distorted, select Keystone.  ON-SCREEN MENU
disappears and Keystone dialog box is displayed.  Correct keystone
distortion by pressing POINT UP/DOWN button(s).   Refer to
KEYSTONE ADJUSTMENT on page 20.
SETTING MENU
Press MENU button and ON-SCREEN MENU will appear.  Press
POINT LEFT/RIGHT button(s) to move a red frame pointer to
SETTING icon.1
2
Language
Language used in ON-SCREEN MENU is selectable among English,
German, French, Italian, Spanish, Portuguese, Dutch, Swedish,
Chinese, Korean, and Japanese.
Display
This function decides whether to display On-Screen Displays.
On  ···shows all the On-Screen Displays.
Off ····sets On-Screen Displays disappeared except;
ON-SCREEN MENU 
“Power off?” message 
P-TIMER 
“No signal” message
“Wait a moment! message
Set the red frame
pointer to the item and
press SET button.Press POINT DOWN button to move a red frame pointer to the
item that you want to set and then press 
SET button.  Setting
dialog box appears.
Blue back
When this function is “On,” the projector produces a blue image while
input signal is not detected. 
Logo
When this function is “On,” the projector displays our logo when
starting up.
When pressing SET button
at Language, Language
Menu appears.
Move the pointer to the item
and then press POINT
LEFT/RIGHT button(s).
SETTING MENU
SETTING Menu icon 
						

							36
SETTING
This function turns Projection Lamp off when this projector detects
signal interruption and is not used for a certain period in order to
reduce power consumption and maintain the Lamp-life.  (This
projector is shipped with this function ON.)
Power Management function operates to turn Projection Lamp off
when the input signal is interrupted and any button is not pressed
over 5 minutes.  This function operates as follows;
1. When any input signal is interrupted, “No signal” and the
counting down display appears (for 5 minutes).
2. After counting down for 5 minutes, Projection Lamp and
READY Indicator are turned off.  (Cooling Fans keep running.)
3. READY Indicator starts to flash after cooling down Projection
Lamp about for 90 seconds (Power Management mode).  
In this Power Management mode, Projection Lamp is
automatically turned on when the input signal is connected or
projector is operated with any button on Top Control or on
Remote Control Unit again.
Power management
This function is used to reset Lamp Replace Counter.  When
replacing Projection Lamp, reset Lamp Replace Counter by using
this function.  Refer to page 38 for operation.
Lamp counter reset
Remote control
This projector has two different remote control codes; the factory-set
normal code (Code 1) and the secondary code (Code 2).  This
switching function prevents remote control operation mixture (jam)
when operating several projectors or video equipment together.  
When operating projector in “Code 2,”  both projector and Remote
Control Unit must be switched to “Code 2.”  
To change the code of the Projector;
Set Remote control in the SETTING MENU to “Code 2.”
To change the code of the Remote Control Unit;
Press both MENU and IMAGE buttons on Remote Control Unit
together for over 10 seconds.
After changing the code, make sure Remote Control Unit operates
properly.  
To return to the normal code (Code 1), operate both the projector
and Remote Control Unit in the ways above again. 
NOTE : When batteries of Remote Control Unit are replaced or ALL-
OFF switch is turned to “ALL-OFF,” the remote control code
automatically returns to the normal code (Code 1).  
On start
When this function is “On,” the projector is automatically turned on
just by connecting AC Power cord to a wall outlet.
Note ; Be sure to turn the projector off properly (refer to the section
“TURNING OFF PROJECTOR” on P19).  If the projector is
turned off in the wrong steps, On Start function does not
operate properly.
Move the pointer to the item and
then press POINT LEFT/RIGHT
button(s).
Press SET button at this icon to dis-
play other items.
Press SET button at this icon to dis-
play previous items.
Time left until Lamp off. 
						

							37
APPENDIX
LAMP REPLACEMENT
LAMP REPLACE
When the life of the Projection Lamp of this projector draws to an end,
the LAMP REPLACE indicator lights yellow.  If this indicator lights
yellow, replace the projection lamp with a new one promptly.
Follow these steps to replace the lamp assembly.
LAMP
ASSEMBLYHANDLE LAMP COVER
ORDER REPLACEMENT LAMP
Replacement Lamp can be ordered through your dealer.  When ordering a Projection Lamp, give the
following information to the dealer.

Model No. of your projector   : LV-7355 / LV-7350
Replacement Lamp Type No. : LV-LP11
(Service Parts No. 610 293 2751)
For continued safety, replace with a lamp assembly of
the same type.
Do not drop a lamp assembly or touch a glass bulb! The
glass can shatter and may cause injury.Allow a projector to cool, for at least 45 minutes before
you open Lamp Cover.  The inside of a projector can
become very hot.
US
Y
NELAMP
REPLACE
LAMP
WARNING
TEMP.
This indicator lights yellow
when the life of the projection
lamp draws to an end.
Replace the Projection Lamp
with a new one promptly.
TOP CONTROL
CAUTION
SCREW
SCREW
Turn off the projector and disconnect the AC plug.  Allow the
projector to cool for at least 45 minutes.
Loosen 3 screws with a screwdriver and pull out Lamp Assembly
by grasping Handle.
1
3
Replace Lamp Assembly with a new one and tighten 3 screws
back into position.  Make sure that Lamp Assembly is set
properly.  Replace Lamp Cover and tighten the screw.4
To remove Lamp Cover, remove the screw with a screwdriver.2
Connect AC Power Cord to the projector and turn on the
projector.
6Reset the Lamp Replace Counter.
Refer to “LAMP REPLACE COUNTER” on the next page .
5 
						

							38
APPENDIX
LAMP REPLACE COUNTER
Be sure to reset the Lamp Replace Counter after the Lamp Assembly is replaced.  When the Lamp Replace Counter is reset,
the LAMP REPLACE Indicator stops lighting.
NOTE : Do not reset the Lamp Replace Counter until after the Projection Lamp is replaced.
Turn projector on, press MENU button and ON-SCREEN
MENU will appear.  Press POINT LEFT/RIGHT button(s) to
move a red frame pointer to SETTING Menu icon (refer to
page 35, 36).
Press POINT DOWN button to move a red frame pointer to
“Lamp counter reset” and then press 
SET button.  The
message Lamp replace counter reset? is displayed.  Move
the pointer to [Yes] and then press SET button.
1
2
Another confirmation dialog box appears and select [Yes] to
reset Lamp Replace Counter.3
This projector uses a high-pressure lamp which must be handled carefully and properly.  Improper
handling may result in accidents, injury, or create a fire hazard.
Lamp lifetime may differ from lamp to lamp and according to the environment of use.  There is no
guarantee of the same lifetime for each lamp.  Some lamps may fail or terminate their lifetime in a
shorter period of time than other similar lamps.
If the projector indicates that the lamp should be replaced, i.e., if the LAMP REPLACE INDICATOR
lights up, replace the lamp with a new one IMMEDIATELY after the projector has cooled down.  
( Follow carefully the instructions in the LAMP REPLACEMENT section of this manual.  )  Continuous
use of the lamp with the LAMP REPLACE INDICATOR lighted may increase the risk of lamp explosion.  
A Lamp may explode as a result of vibration, shock or degradation as a result of hours of use as its
lifetime draws to an end.  Risk of explosion may differ according to the environment or conditions in
which the projector and lamp are being used.
IF A LAMP EXPLODES, THE FOLLOWING SAFETY PRECAUTIONS SHOULD BE TAKEN.
If a lamp explodes, disconnect the projector’s AC plug from the AC outlet immediately.  Contact an
authorized service station for a checkup of the unit and replacement of the lamp.  Additionally, check
carefully to ensure that there are no broken shards or pieces of glass around the projector or coming out
from the cooling air circulation holes.  Any broken shards found should be cleaned up carefully.  No one
should check the inside of the projector except those who are authorized trained technicians and who are
familiar with projector service.  Inappropriate attempts to service the unit by anyone, especially those who
are not appropriately trained to do so, may result in an accident or injury caused by pieces of broken
glass.  
LAMP HANDLING PRECAUTIONS
Move the pointer to Lamp counter reset and then press
SET button.  The message “Lamp replace counter
reset?” is displayed. 
						

							39
APPENDIX
OPERATING WIRELESS MOUSE
INSTALLATION
Remote Control Unit is not only able to operate this projector but also usable as a wireless mouse for most Personal
Computers.  POINT buttons and two CLICK buttons are used for wireless mouse operation.
This Wireless Mouse function is available only when PC mouse pointer is displayed on a projected screen.  When ON-
SCREEN MENU or any message / dialog box is displayed on the screen instead of PC mouse pointer, this Wireless Mouse
function cannot be used.
Connect the mouse port (or USB port) of your computer to
Control Port (or USB connector) of this projector with Control
Cable (or USB cable). (Refer to page 11, 12 for connection.)
Turn the projector on first, and then turn on your computer.
When the computer is switched on first, Wireless Mouse may not
work properly.
1
2
To use Remote Control Unit as Wireless Mouse for a Personal Computer, installation of the mouse driver (not supplied) is
required.  Make sure that the mouse driver is properly installed in your computer and that the mouse port (or USB port) of
your computer is activated.
OPERATING WIRELESS MOUSE
When controlling a PC mouse pointer, operate Wireless Mouse with POINT button, SET button, and RIGHT CLICK button on
Remote Control Unit.
Used to move PC mouse pointer.  The pointer is moved
corresponding with the direction you are pressing.
POINT button
This button has the same function as the left button in a PC mouse.
SET (LEFT CLICK) button
This button has the same function as the right button in a PC mouse.
This button is not available for controlling this projector.
RIGHT CLICK button
Note :When your computer has no mouse
port, connect Serial Port of your
computer to Control Port of the
projector with Control Cable for Serial
Port (not supplied).
POINT button (Move the pointer)
SET button
(left button of the
mouse)
RIGHT CLICK  button
(right button of the mouse) 
						

							40
APPENDIX
CLEANING PROJECTION LENS
Apply a non-abrasive camera lens cleaner to a soft, dry cleaning cloth.  Avoid using an excessive amount of cleaner.
Abrasive cleaners, solvents or other harsh chemicals might scratch a surface.
When the projector is not in use, replace Lens Cover.
1
3
Lightly wipe a cleaning cloth over Projection Lens.2
Follow these steps to clean Projection Lens:
MAINTENANCE
WARNING TEMP. INDICATOR
WARNING TEMP. Indicator flashes red when an internal temperature of the projector exceeds the normal temperature.  This
Indicator stops flashing when the temperature of the projector returns to normal.
When WARNING TEMP. Indicator continues to flash, check the items listed below.
Ventilation Slots of the projector may be blocked.  In such an event, reposition the projector so that Ventilation Slots
are not obstructed.
AIR FILTER CARE AND CLEANING
Air Filter may be clogged with dust particles.  Clean Air Filter by following the section AIR FILTER CARE AND
CLEANING below.
1
2
If WARNING TEMP. Indicator remains on after performing the above checks, Cooling Fans or the Internal Circuits may
be malfunctioning.  Contact service personnel from an authorized dealer or a service station.3
AIR FILTER
Pull up and remove.
Turn off the projector, and disconnect AC power cord from the
AC outlet.
Turn the projector upside down and remove Air Filter by pulling
the latches upward.
1
2
Removable Air Filter prevents dust from accumulating on the surface of Projection Lens and Projection  Mirror.  Should Air
Filter become clogged with dust particles, it will reduce Cooling Fans’ effectiveness and may result in internal heat build up
and adversely affect the life of the projector.  Clean Air Filter following the steps below: 
Clean Air Filter with a brush or wash out dust and particles.3
Replace Air Filter properly. Make sure that Air Filter is fully
inserted.4
CAUTION
Do not operate the projector with Air Filter removed.  Dust
may accumulate on LCD Panel and Projection Mirror, and
may degrade picture quality.
Do not put small parts into Air Intake Vents.  It may result in
malfunction of the projector.
RECOMMENDATION
We recommend avoiding dusty/smoky environment when operating a projector.  Usage in these environments may
cause poor image quality.
When using under dusty or smoky conditions, dust may accumulate on the lens, liquid crystal panels, or optical elements
inside the projector.  This condition may degrade the quality of a projected image.
When the above symptoms are noticed, contact your authorized dealer or service station for proper cleaning.