Canon projector LV7345 User Manual

							21
BASIC OPERATION
Press FREEZE button on Remote Control Unit to freeze the picture on-screen.  To cancel FREEZE function, press FREEZE
button again or press any other button.
Press NO SHOW button on Remote Control Unit to black out the
image.  To restore to normal, press NO SHOW button again or press
any other button.
NO SHOW FUNCTION
PICTURE FREEZE FUNCTION
Message disappears after 4 seconds.
No show
Press P-TIMER button on Remote Control unit.  The timer display “00
: 00” appears and the timer starts to count time (00 : 00 ~ 59 : 59).  
To stop P-TIMER display, press P-TIMER button.  And then, press P-
TIMER button again to cancel P-TIMER function.
P-TIMER FUNCTION
1
2
Press MENU button and ON-SCREEN MENU will appear.  Press
POINT LEFT/RIGHT buttons to move a red frame pointer to
SOUND Menu icon. 
Volume
Press VOLUME (+/–) button(s) on Top Control or on Remote Control
Unit to adjust volume.  Volume dialog box appears.  (+) button to
increase volume, and (–) button for decreasing.
Mute
Press MUTE button on Remote Control Unit to cut off sound.  To
restore sound to its previous level, press MUTE button again or press
Volume (+/–) button(s).
Press POINT RIGHT button to increase volume, and press POINT
LEFT button for decreasing. 
Press POINT LEFT/RIGHT button to cut off sound.  Dialog box display
is changed to “On” and sound is cut off.  To restore sound to its
previous level, press POINT LEFT/RIGHT button again.
Press POINT DOWN button to move a red frame pointer to the
item that you want to select, and then press SET button.
Indicates roughly level of volume.
Close SOUND Menu.
SOUND ADJUSTMENT
DIRECT OPERATION
MENU OPERATION
Volume
Mute
Indicates roughly level of
volume.
Press MUTE button to set
Mute function On or Off.
Dialog box disappears after 4 seconds.  
SOUND MENU
SOUND Menu icon 
						

							22
COMPUTER INPUT
SELECTING INPUT SOURCE
MENU OPERATION
DIRECT OPERATION
Choose Computer by pressing INPUT button on Top Control or on
Remote Control Unit.
If projector cannot reproduce proper image, select correct input source
through MENU OPERATION (see below).
Press MENU button and ON-SCREEN MENU will appear.  Press
POINT LEFT/RIGHT button to move a red frame pointer to
INPUT Menu icon.
Press POINT DOWN button to move a red arrow pointer to
Computer and then press SET button.  Source Select Menu will
appear.   
1
2
INPUT button
Computer
Video
Move a pointer (red arrow)
to Computer and press SET
button.
Move a pointer to RGB
(Digital) or RGB (Analog)
and press SET button.
Source Select Menu
INPUT MENU
INPUT Menu icon
SELECTING COMPUTER SYSTEM
This projector automatically tunes to most different types of computers based on VGA, SVGA, XGA or SXGA (refer to
“COMPATIBLE COMPUTER SPECIFICATION” on page 23).  When selecting Computer, this projector automatically tunes
to incoming signal and projects proper image without any special setting.  (Some computers need setting manually.)
Note : Projector may display one of the following messages.
When projector cannot recognize connected signal as PC
system provided in this projector, Auto PC Adjustment
function operates to adjust projector and the message
“Auto” is displayed on SYSTEM Menu icon.  (Refer to
P24.)  When image is not provided properly, manual
adjustment is required.  (Refer to P25 and 26.)
There is no signal input from computer.  Make sure the
connection of computer and a projector is set correctly.  
(Refer to TROUBLESHOOTING on page 40.)
Auto
––––
SYSTEM Menu icon
Displays system being
selected.
PC SYSTEM MENU
SELECT COMPUTER SYSTEM MANUALLY
SYSTEM Menu icon 
Displays system being selected.
The systems on this dialog box
can be selected.
Press MENU button and ON-SCREEN MENU will appear.  Press
POINT LEFT/RIGHT buttons to move a red frame pointer to PC
SYSTEM Menu icon.
Press POINT DOWN button to move a red arrow pointer to the
system that you want to set, and then press 
SET button.  
1
2
PC SYSTEM MENU
Custom Mode (1~5) set in PC
ADJUST Menu.  (P25, 26)
This projector automatically selects PC system among those provided
in this projector and PC system can be also selected manually.
Move a pointer to either RGB (Digital) or RGB (Analog) and then
press SET button.3
When your computer is connected to RGB INPUT
(DIGITAL) terminal, select RGB (Digital).RGB (Digital)
When your computer is connected to RGB INPUT
(ANALOG) terminal, select RGB (Analog).RGB (Analog)
Computer 
						

							23
COMPUTER INPUT
COMPATIBLE COMPUTER SPECIFICATIONS
Basically this projector can accept the signal from all computers with the V, H-Frequency below mentioned and less than 140
MHz of Dot Clock.
NOTE : Specifications are subject to change without notice.
ON-SCREEN
DISPLAYRESOLUTIONH-Freq.
(kHz)V-Freq.
(Hz)
VGA 1640 x 48031.4759.88
VGA 2720 x 40031.4770.09
VGA 3640 x 40031.4770.09
VGA 4640 x 48037.8674.38
VGA 5640 x 48037.8672.81
VGA 6640 x 48037.5075.00
MAC LC13640 x 48034.9766.60
MAC 13640 x 48035.0066.67
MAC 16832 x 62449.7274.55
MAC 191024 x 76860.2475.08
MAC 211152 x 87068.6875.06
MAC1280 x 96075.0075.08
MAC1280 x 102480.0075.08
SVGA 1800 x 60035.15656.25
SVGA 2800 x 60037.8860.32
SVGA 3800 x 60046.87575.00
SVGA 4800 x 60053.67485.06
SVGA 5800 x 60048.0872.19
SVGA 6800 x 60037.9061.03
SVGA 7800 x 60034.5055.38
SVGA 8800 x 60038.0060.51
SVGA 9800 x 60038.6060.31
SVGA 11800 x 60038.0060.51
ON-SCREEN
DISPLAYRESOLUTIONH-Freq.
(kHz)V-Freq.
(Hz)
XGA 101024 x 768
XGA 111024 x 768
XGA 121024 x 768
XGA 131024 x 768
62.0477.07
XGA 141024 x 768
61.0075.70
XGA 151024 x 768
35.52286.96
(Interlace)
46.9058.20
XGA 81024 x 768
47.0058.30
XGA 91024 x 768
58.0372.00
SXGA 11152 x 864
SXGA 21280 x 1024
63.4879.35
SXGA 31280 x 1024
36.0087.17
(Interlace)
SXGA 41280 x 1024
64.2070.40
SXGA 51280 x 1024
62.5058.60
SXGA 61280 x 1024
63.9060.00
SXGA 71280 x 1024
63.3459.98
SXGA 81280 x 1024
63.7460.01
SXGA 111152 x 900
71.6967.19
SXGA 121152 x 900
81.1376.107
SXGA 131280 x 1024
63.9860.02
SXGA 141280 x 1024
61.2065.20
71.4075.60
50.0086.00
(Interlace)
720p (HDTV)––––––––
50.0094.00
(Interlace)
45.0060.00
XGA 11024 x 768
XGA 21024 x 768
XGA 31024 x 768
XGA 41024 x 768
48.3660.00
68.67784.997
XGA 61024 x 768
60.02375.03
XGA 71024 x 768
56.47670.07
48.5060.02
44.0054.58
SXGA 91280 x 1024
SXGA 101280 x 960
79.97675.025
60.0060.00
SXGA 151280 x 1024
SXGA 161280 x 1024
SXGA 171152 x 900
SXGA 181280 x 1024
63.3760.01
76.9772.00
61.8566.00
46.4386.70
(Interlace)
SXGA 191280 x 102463.7960.18
XGA 51024 x 76860.3174.92
VGA 7640 x 48043.26985.00
RGB––––––––15.73460
(Interlace)RGB––––––––15.62550
(Interlace)
1080i (HDTV)––––––––33.7560.00
(Interlace)1035i (HDTV)––––––––33.7560.00
(Interlace)
SVGA 10800 x 60032.7051.09
ON-SCREEN
DISPLAYRESOLUTIONH-Freq.
(kHz)V-Freq.
(Hz)
D-VGA640 x 48031.46959.940
D-SVGA800 x 60037.87960.317
D-SXGA11280 x 102463.98160.020
When the input signal is from the COMPUTER INPUT DIGITAL terminal, refer to the chart below.
ON-SCREEN
DISPLAYRESOLUTIONH-Freq.
(kHz)V-Freq.
(Hz)
D-XGA1024 x 76848.36360.004
D-SXGA21280 x 102460.27658.069
D-SXGA31280 x 102431.6529.8
(Interlace) 
						

							24
COMPUTER INPUT
PC ADJUSTMENT
AUTO PC ADJUSTMENT
Auto PC Adjustment function is provided to automatically adjust Fine sync, Total dots and Picture Position to conform to your
computer.  Auto PC Adjustment function can be operated as follows.
Press MENU button and ON-SCREEN MENU will appear.  Press
POINT LEFT/RIGHT button to move a red frame pointer to PC
ADJUST Menu icon.1
2Press POINT DOWN button to move a red frame pointer to
AUTO PC Adj. icon and then press SET button twice.
This Auto PC Adjustment can be also executed by pressing
AUTO PC ADJ. button on Remote Control Unit.
Move a red frame pointer to AUTO PC Adj.
icon and press SET button.
PC ADJUST MENU
Auto PC Adj.
PC ADJUST Menu icon
Store adjustment parameters.
Adjustment parameters from Auto PC Adjustment can be memorized
in this projector.  Once parameters are memorized, setting can be
done just by selecting Mode in PC SYSTEM Menu (P22).  Refer to
step 3 of MANUAL PC ADJUSTMENT section (P26).
NOTE
Fine sync, Total dots and Picture Position of some computers can
not be fully adjusted with this Auto PC Adjustment function.  When
the image is not provided properly through this function, manual
adjustments are required.  (Refer to page 25, 26.)
Auto PC Adjustment function cannot be operated when “RGB,”
“720p (HDTV),” “1035i (HDTV)” or “1080i (HDTV)” is selected on PC
SYSTEM Menu (P22). 
						

							25
COMPUTER INPUT
MANUAL PC ADJUSTMENT
This projector can automatically tune to the display signals from most personal computers currently distributed.  However,
some computers employ special signal formats which are different from the standard ones and may not be tuned by Multi-
Scan system of this projector.  If this happens, projector cannot reproduce a proper image and the image may be recognized
as a flickering picture, a non-synchronized picture, a non-centered picture or a skewed picture.
This projector has a Manual PC Adjustment to enable you to precisely adjust several parameters to match with those special
signal formats.  This projector has 5 independent memory areas to memorize those parameters manually adjusted.  This
enables you to recall the setting for a specific computer whenever you use it. 
Note : This PC ADJUST Menu cannot be operated when the input signal is from RGB INPUT (DIGITAL) terminal or “RGB” is
selected on PC SYSTEM MENU (P22).
Press MENU button and ON-SCREEN MENU will appear.  Press
POINT LEFT/RIGHT button to move a red frame pointer to PC
ADJUST Menu icon.1
2Press POINT DOWN button to move a red frame pointer to the
item that you want to adjust and then press SET button.
Adjustment dialog box will appear.  Press POINT LEFT/RIGHT
button to adjust value.
Move a red frame icon to the item and
press SET button.
PC ADJUST MENU
PC ADJUST Menu icon
Adjusts an image as necessary to eliminate flicker from the display.
Press POINT LEFT/RIGHT button to adjust value.(From 0 to 31.)
Fine sync
The number of total dots in one horizontal period.  Press POINT
LEFT/RIGHT button(s) and adjust number to match your PC image.
Total dots
Adjusts horizontal picture position.  Press POINT LEFT/RIGHT
button(s) to adjust the position.
Horizontal
Adjusts vertical picture position.  Press POINT LEFT/RIGHT
button(s) to adjust the position.
Vertical
Press SET button to show the information of computer selected.
Current mode
Adjusts clamp level.  When the image has a dark bar(s), try this
adjustment.
Clamp
Press SET button at this icon to adjust
“Clamp,” “Display area (H/V)” or set
“Full screen.”
Press POINT LEFT/RIGHT
button to adjust the value.
Shows status
(Stored / Free) of the
selected Mode. Selected Mode
Press SET button at Current
mode icon to show the
information of computer
connected.
Current mode 
						

							26
COMPUTER INPUT
NOTE : Fine sync, Total dots, Display area (H/V) and Full screen
cannot be adjusted when “1035i (HDTV)” or “1080i (HDTV)”
is selected on PC SYSTEM Menu (P22).
Selects area displayed with this projector.  Select the resolution at
Display area dialog box.
Display area
Adjustment of horizontal area displayed with this projector.  Press
POINT LEFT/RIGHT button(s) to decrease/increase value and then
press SET button.
Display area H
Adjustment of vertical area displayed with this projector.  Press
POINT LEFT/RIGHT button(s) to decrease/increase value and then
press SET button.
Display area V
Press POINT LEFT/RIGHT button(s) to switch Full screen function to
“On” or “Off.”  Set “On” to resize the image with 4 x 3 aspect ratio to
fit the screen.
Full screen
Reset
Store
Closes PC ADJUST MENU.
Quit
Other icons operates as follows.
3
To store adjustment parameters, move a red frame pointer to
Store icon and then press SET button.  Move a red arrow pointer
to any of Mode 1 to 5 that you want to store to and then press
SET button.
Reset all adjust parameters on adjustment dialog box to previous
figure.
Mode free
Vacant Mode Shows values of “Total dots,”
“Horizontal,” “Vertical,” “Display
area H,” and “Display area V.”
Store icon
Mode free iconClose this dialog box.
To store adjustment data.
To clear adjustment data.
To clear adjustment parameters previously set, move a red
frame pointer to Mode free icon and then SET button.  Move a
red arrow pointer to the Mode that you want to clear and then
press SET button.
Display area
Press POINT LEFT
/RIGHT button(s) to
adjust value and then
press SET button.Press SET button at Display
area icon and Display area
dialog box appears.
This Mode has parameters being stored. 
						

							27
COMPUTER INPUT
PICTURE IMAGE ADJUSTMENTS
IMAGE LEVEL SELECT (MENU)
Press MENU button and ON-SCREEN MENU will appear.  Press
POINT LEFT/RIGHT button to move a red frame pointer to
IMAGE SELECT Menu icon.1
2Press POINT DOWN button to move a red frame pointer to the
level that you want to set and then press SET button.
Move a red frame pointer to the level
and press SET button.
The level being selected.
IMAGE SELECT MENU
Normal picture adjustment preset on this projector.  
Standard
Picture adjustment improved in reproduction of halftones.  This
adjustment is suitable for providing better image in brighter place.
High contrast
User preset picture adjustment in IMAGE ADJUST Menu (P28).
Custom
IMAGE SELECT
Menu icon
IMAGE LEVEL SELECT (DIRECT)
Select image level among Standard, High contrast and Custom by
pressing IMAGE button on Remote Control Unit.IMAGE button
Standard
High contrast
Custom
Normal picture adjustment preset on this projector.  
Picture adjustment improved in reproduction of halftones.  This
adjustment is suitable for providing better image in brighter place.
User preset picture adjustment in IMAGE ADJUST Menu (P28).
Standard
High contrast
Custom 
						

							28
COMPUTER INPUT
Press POINT LEFT/RIGHT buttons
to adjust value.
Reset all adjustment to previous figure.
Reset
Store
Closes IMAGE MENU.
Quit
Other icons operates as follows.
Press MENU button and ON-SCREEN MENU will appear.  Press
POINT LEFT/RIGHT buttons to move a red frame pointer to
IMAGE ADJUST Menu icon.1
2Press POINT DOWN button to move a red frame pointer to the
item that you want to adjust. and then press SET button.  The
level of each item is displayed.  Adjust each level by pressing
POINT LEFT/RIGHT button(s).
Move a red frame pointer to
the item to be selected and
then press SET button.
IMAGE ADJUST MENU
IMAGE LEVEL ADJUSTMENT
Press POINT LEFT button to decrease contrast, and POINT RIGHT
button to increase contrast.  (From 0 to 63.)
Press POINT LEFT button to adjust image darker, and POINT
RIGHT button to adjust brighter.  (From 0 to 63.)
Contrast
Brightness
Press either POINT LEFT button or POINT RIGHT button to obtain
better balance of contrast.  (From 0 to 15.)
Gamma
3
To store manually preset image level, move a red frame pointer
to Store icon and press SET button.  The message “OK?” will
appear.  Select [Yes] to store manual adjustment.
To set this manual adjustment, select Custom by pressing
IMAGE button or through IMAGE SELECT MENU (refer to P27).
Store icon
Press SET button at this icon to
store the adjustment.
IMAGE ADJUST
Menu icon
Press POINT LEFT button to lighten red tone and POINT RIGHT
button to deeper tone.  (From 0 to 63.)
White balance (Red)
Press POINT LEFT button to lighten green tone and POINT RIGHT
button to deeper tone.  (From 0 to 63.)
White balance (Green)
Press POINT LEFT button to lighten blue tone and POINT RIGHT
button to deeper tone.  (From 0 to 63.)
White balance (Blue)
Selected Image level
“OK?” message
Move a red arrow
pointer to [Yes] and
then press SET button. 
						

							29
COMPUTER INPUT
PICTURE SCREEN ADJUSTMENT
This projector has a picture screen resize function, which enables you to display the desirable image size.
Press MENU button and ON-SCREEN MENU will appear.  Press
POINT LEFT/RIGHT button(s) to move a red frame pointer to
SCREEN Menu icon.
When Digital zoom + is selected, ON-SCREEN MENU disappears
and the message “D. Zoom +” is displayed.  Press SET button to
expand image size.  And press POINT UP/DOWN/LEFT/RIGHT
button(s) to pan the image.  Panning function can work only when
the image is larger than screen size.
A projected image can be also expanded by pressing D.ZOOM 
button on Remote Control Unit.  
1
To cancel Digital Zoom +/– mode, press any button except D.ZOOM
/, SET, POINT and LASER buttons.
Move a red frame pointer to the
function and press SET button.
Press POINT DOWN button and move a red frame pointer to the
function that you want to select and then press SET button.2
Wide
Digital zoom +
NOTE
This SCREEN Menu cannot be operated when
“1035i (HDTV)” or “1080i (HDTV)” is selected on
PC SYSTEM Menu  (P22).
Wide cannot be selected when “720p (HDTV)” is
selected on PC SYSTEM Menu  (P22).
True and Digital zoom +/– cannot be selected
when “RGB” is selected on PC SYSTEM Menu
(P22).
This projector cannot display any resolution higher
than 1280 X 1024.  If your computer’s screen
resolution is higher than 1280 X 1024, reset the
resolution to the lower before connecting projector.
The image data in other than XGA (1024 x 768) is
modified to fit the screen size in initial mode.
Panning function may not operate properly if the
computer system prepared on PC ADJUST Menu
is used.
Provides image to fit screen size.
Normal
True
SCREEN MENU
SCREEN Menu icon
When Digital zoom – is selected, ON-SCREEN MENU disappears
and the message “D. Zoom –” is displayed.  Press SET button to
compress image size. 
A projected image can be also compressed by pressing D.ZOOM 
button on Remote Control Unit.  
Digital Zoom –
Provides image in its original size.  When the original image size is
larger than screen size (1024 x 768), this projector enters “Digital
zoom +” mode automatically. 
Provides image to fit wide video aspect ratio (16 : 9) by expanding
image width uniformly.  This function can be used for providing a
squeezed video signal at 16 : 9. 
						

							30
VIDEO INPUT
SELECTING INPUT SOURCE
MENU OPERATION
DIRECT OPERATION
Choose Video by pressing INPUT button on Top Control or on Remote
Control Unit.
If projector cannot reproduce proper video source, select correct input
source through MENU OPERATION (see below).
Press MENU button and ON-SCREEN MENU will appear.  Press
POINT LEFT/RIGHT button to move a red frame pointer to
INPUT Menu icon.
Press POINT DOWN button to move a red arrow pointer to
Video and then press SET button.  Source Select Menu will
appear. 
1
2
Move a pointer to Video and
press SET button.
Move a pointer to the source and press SET button.
Source Select Menu (VIDEO)
INPUT MENU
INPUT button
Video
Computer
Move a pointer to the source that you want to select and then
press SET button.3
Projector automatically detects incoming Video signal,
and adjusts itself to optimize its performance.
•When both Y jack and S-VIDEO jack are connected, S-
VIDEO jack has priority over Y jack.
•When both Y-Pb/Cb-Pr/Cr jacks and S-VIDEO jack are
connected, Y-Pb/Cb-Pr/Cr jacks have priority over S-
VIDEO jack.Auto
When video input signal is connected to Y jack, select
Video.Video
When video input signal is connected to S-VIDEO jack,
select S-Video.S-Video
When video input signal is connected to Y-Pb/Cb-
Pr/Cr jacks, select Y, Pb/Cb, Pr/Cr.Y,Pb/Cb,Pr/Cr
VIDEO