Canon projector LV7295 User Manual

							
Setting

61

Setting

Use the Point ▲▼ buttons to select Off, On 1 or On 2, and then press the OK button to make a choice.
Change	the	PIN	code	lock	setting
Enter	a	PIN	code
Use  the  Point ▲▼  buttons  to  enter  a  number.  Press the  Point ◄ ►  buttons  to  fix  the  number  and  move the  red  frame  pointer  to  the  next  box.  The  number changes  to .  If  you  fixed  an  incorrect  number, use  the  Point ◄ ► buttons  to  move  the  pointer  to the  number  you  want  to  correct,  and  then  enter  the correct number.
Repeat this step to complete entering a four-digit number.
After entering the four-digit number, move the pointer to Set. Press the OK button so that you can change the following PIN code lock setting.
If you entered an incorrect PIN code, PIN	code and the number () will turn red for a moment. Enter the correct PIN code all over again.
Enter	a	PIN	code
Change	the	PIN	code	
Change	the	PIN	code
CAUTION:WHEN	YOU	HAVE	CHANGED	THE	LOGO	PIN	CODE,	WRITE	DOWN	THE	NEW	PIN	CODE	AS	A	REMINDER.	IF	YOU	FORGET	YOUR	PIN	CODE,	THE	PROjECTOR	CAN	NO	LONGER	BE	STARTED.
The PIN code can be changed to your desired four-digit number. Press the OK button to select PIN	code	change. Pin code dialog box appears, use the Point ▲▼ buttons to enter the correct code. The New PIN code input dialog box appears. Set a new PIN code.
Note:If you forget your PIN code and unable to change it, the PIN code can be reset to the factory default setting (134) according to the following procedures.When you reset the PIN code, the Logo PIN code and Key lock will be reset, as well.1. Unplug  the  AC  Power  Cord  from  the  AC outlet.. Hold down the OK button on the projector and connect the AC Power Cord into the outlet again. Keep holding down the OK button until the POWER indicator lights. The PIN code returns to the factory default setting while the PIN code lock state will remain the same as the previous set state. 
						

							
6

Setting

This function provides the following options in the cooling fans’ operation when the projector is turned off (p.3). L 1 .....  Normal operation L 2 .....  Slower, lower-sound and longish-time than the normal operation (L 1).
Fan
Choose  the  running  speed  of  cooling  fans  from  the following  options  according  to  the  ground  elevation under which you use the projector. Off................ Normal speed. Set this function to                        Off when using the projector in non-                      high altitude environment. On 1............. Faster than Off mode. Select this                         mode when using the projector in                       high altitudes (about 1,000 meters                       to ,000 meters above the sea level)                       where the fans have less cooling                        effect. On 2............. Faster than On 1 mode. Select this                       mode when using the projector in                       higher altitudes (about ,000 meters                             to 3,000 meters above the sea level)                       where the fans have lesser cooling                       effect.
Fan	control
Lamp	counter	
Be sure to reset the Lamp replacement counter after the lamp is replaced. (p.68) Press the Point ▲▼ buttons to choose the Lamp counter function and then press the Point ► or the OK button to access the submenu items. Lamp	counter................This item shows the total accumulated time of the lamp usage.Lamp	counter	reset.......Press the OK button to     choose Lamp	counter	reset. Select Yes in the confirmationbox if you want to reset the          lamp counter, and then choose Yes in the second confirmation box to reset lamp counter.
When you want to make a digital processing of a projected image faster, set this function.Use the Point ▲▼ buttons, select an item of Off or On.
Note:Noise	reduction and Progressive can not be selected when Video delay control function is set to On.
Video	delay	control
Note:The fan noise becomes louder in On 1 and On 2. 
Lamp	counter	reset 
						

							
Setting

63

Setting

Factory	default
This function returns all setting values except for the User	logo, PIN	code	lock, Logo	PIN	code	lock, Lamp	counter and Filter	counter to the factory default settings.
Factory	default
Warning	log
This function records anomalous operations while the projector is in operation and use it when diagnosing faults. Up to 10 warning logs are displayed with the latest warning message at the top of the list, followed by previous warning messages in chronological order. 
Note:   When the Factory default function is executed, all the warning log records will be deleted.
This function is used to set a frequency for the filter cleaning.Use the Point ▲▼ buttons to select Filter counter and then press the Point ► or the OK button to access the submenu items.
Filter	counter.........Show the total accumulated time                                  of the filter use timer setting.Timer..................... To set a timer, when the projector reaches the time, the Filter warning icon (Fig.1) appears on the screen and the total accumulated time turns red, indicating that the filter replacement is necessary.Filter	counter	reset... After replacing the filter, be sure to reset the timer. The Filter warning icon will not turn off until the filter counter is reset. For details about resetting the timer, refer to “Resetting the Filter Counter” on page 66.
Filter	counter	
Filter	counter
Press the OK button to select Timer, and then use the Point ▲▼ buttons to set the timer. Select from (Off/2000H/3000H/4000H) depending on the use environment.
Filter warning icon appears on the screen at a set time (Off/2000H/3000H/4000H).
Fig .1   Filter warning icon
Note: •   This icon also appears at turning on. • The Filter warning icon (Fig.1) will not appear when the Display function is set to Off (p.53), during Freeze	(p.8), or Blank (p.9). 
						

							
64

Input	Source	Information	Display
The Information Menu is used for checking the status of the image signal\
 being projected and the operation of the projector.
H-sync	freq.
V-sync	freq.
Lamp	counter
Information	Menu
The horizontal frequency of the input signal is displayed in KHz, or -	-	-	- KHz	when no signal.
The vertical frequency of the input signal is displayed in Hz, or -	-	-	-	Hz	when no signal. Numbers of Hz doubles when during Interlace.
The cumulative lamp operating time is displayed.
Press the INFO. button on the remote control unit to display the Information Menu.
INFO.	button
Remote	control	unit
Press the Point ▲▼ buttons to select the Information. The Information Menu is displayed. 
See below for displayed information.
Power	management	mode
Aspect
Off, Standby or Exit, and Timer are displayed.
The selected Screen size is displayed.
Input
Lamp	status
The selected input source is displayed.
The selected lamp mode is displayed.
Language
The selected language is displayed.
Key	lock
The selected Key lock icon is displayed.
PIN	code	lock
Off or On 1 or On 2 is displayed.
Remote	control
The selected remote code  is displayed.
Direct Operation
Menu Operation
SERIAL	NO.
The serial number of the projector is displayed. The serial number is used to service the projector.
InformationMaintenance	and	Cleaning 
						

							
65

OK
POWER
AUTO SET
MENU
LAMP REPLACE
WARNING
VOLVOL

The WARNING indicator shows the state of the function which protects the proj\
ector. Check the state of the WARNING indicator and the POWER indicator to take proper maintenance. 
WARNING	indicator
The	projector	is	shut	down	and	the	WARNING	indicator	is	blinking	red.
When the temperature inside the projector reaches a certain level, the projector will be automatically shut down to protect the inside of the projector. The POWER indicator is blinking while the projector is being cooled down. When the projector has cooled down enough (to its normal operating temperature), it can be turned on again by pressing the POWER button.
The	projector	is	shut	down	and	the	WARNING	indicator	lights	red.
When the projector detects an abnormal condition, it is automatically shut down to protect the inside of the projector and the WARNING indicator lights red. In this case, unplug the AC power cord and reconnect it, and then turn the projector on once again to verify operation. If the projector cannot be turned on and the WARNING indicator still lights red, unplug the AC power cord and contact the service center. 
	WARNINGDO	NOT	LEAVE	THE	PROjECTOR	WITH	THE	AC	POWER	CORD	CONNECTED	UNDER	 AN	ABNORMAL 	CONDITION.	IT	MAY	RESULT	IN	FIRE	OR	ELECTRIC	SHOCK.		
Top	Control
Top	Control
Note:The WARNING indicator continues to blink even after the temperature inside the projector returns to normal. When the projector is turned on again, the WARNING  indicator stops blinking. 
Then	check	the	matters	below:
–  Did you provide appropriate space for the projector to be ventilated? Check the installing condition to see if the air vents of the projector are not blocked.–  Has the projector been installed near an Air-Conditioning/ Heating Duct or Vent? Move the installation of the projector away from the duct or vent.–  Is the filter clean? Clean the filter periodically.
WARNING blinking red
Maintenance	and	Cleaning
OK
POWER
AUTO SET
MENU
LAMP REPLACE
WARNING
VOLVOL
WARNING lights red 
						

							
66

Maintenance	and	Cleaning

Filter prevents dust from accumulating on the optical elements inside th\
e projector. Should the Filter become clogged with dust particles, it will reduce cooling fans’ effectiveness and may result in internal heat buildup and adversely affect the life of the projector.  If a “Filter warning” icon appears on the screen, replace the F\
ilter immediately. Replace the filter by following the steps below.
CAUTION- Do not operate the projector with the filter    removed. Dust may accumulate on the optical    elements degrading picture quality.- Do not put anything into the air vents. Doing so   may result in malfunction of the projector.- Do not wash the filter with water or any other    liquid Matter. Otherwise the filter may be   damaged.
RECOMMENDATION	 We	recommend	avoiding	dusty/smoky	environments	when	you	operate	the	projector.		Usage	in	these	environments	may	cause	poor	image	quality. When using the projector under dusty or smoky conditions, dust may accumulate on a lens, LCD panels, or optical elements inside the projector degrading the quality of a projected image.  When the symptoms above are noticed, contact your authorized dealer or service center for proper cleaning.
Be sure to reset the Filter counter after cleaning or replacing the filter. 
Press the MENU button to display the On-Screen Menu. Use the Point ▲▼ buttons to select Setting and then press the Point ► or the OK button.
Use the Point ▲▼ buttons to select Filter	counter and then press the Point ► or the OK button. Use the Point ▲▼buttons to select Filter	counter	reset and then press the OK button. Filter	counter	Reset? appears. Select Yes to continue.
1
2
Resetting	the	Filter	Counter
Filter	counter	reset
Filter	counter	Reset?	appears.
Select Yes, then another confirmation box appears.
Select Yes again to reset the Filter counter.Another confirmation dialog box appears, select Yes to reset the Filter counter.3
Replacing	the	Filter
Turn off the projector, and unplug the AC power cord from the AC outlet.
Place the latch in the OPEN position and pull out the filter in the arrow direction.
1
2
Slide the new filter (along the guide rails. Make sure that the filter is inserted completely.) Place the latch back in the LOCK position.
3
4
FilterLatch
Connect the AC power cord to the projector and turn on the projector.
5Reset the filter counter.
OPEN
LOCKNote:  • When replacing the filter, it is required a certain space to pull out the filter completely. • When installing the projector, install the projector with keeping a certain space for replacing the filter.  
						

							
Maintenance	and	Cleaning

67

Maintenance	and	Cleaning

Cleaning	the	Projector	Cabinet
Cleaning	the	Projection	Lens
Unplug the AC power cord before cleaning.
Gently wipe the projection lens with a cleaning cloth that contains a small amount of non-abrasive camera lens cleaner, or use a lens cleaning paper or commercially available air blower to clean the lens. 
Avoid using an excessive amount of cleaner. Abrasive cleaners, solvents, or other harsh chemicals might scratch the surface of the lens.
Unplug the AC power cord before cleaning.
Gently wipe the projector body with a soft dry cleaning cloth. When the cabinet is heavily soiled, use a small amount of mild detergent and finish with a soft dry cleaning cloth. Avoid using an excessive amount of cleaner. Abrasive cleaners, solvents, or other harsh chemicals might scratch the surface of the cabinet.
When the projector is not in use, put the projector in an appropriate carrying case to protect it from dust and scratches.
When moving this projector or while not using it over an extended period of time, attach the lens cap.
Attach the lens cap according to the following procedures.
Attaching	the	Lens	Cap
1
2
Thread the string through the hole on the lens cap and then tie a knot in the string to secure it in place.
To pass the other end of the string into the hole on the bottom of the projector and pull at it.
Do not use any flammable solvents or air sprays on the projector and in its vicinity. The explosion or fire hazard may occur even after the AC power cord is unplugged because the temperature inside the projector is extremely high due to the lamps. In addition, there is a risk that the internal parts may be damaged not only by the flammable air spray but also by the cold air.
CAUTION 
						

							
68

Maintenance	and	Cleaning

When the projection lamp of the projector reaches its end of life, the Lamp replacement icon appears on the screen and LAMP REPLACE indicator lights yellow. Replace the lamp with a new one promptly. The timing when the LAMP REPLACE indicator should light is depending on the lamp mode.
Follow these steps to replace the lamp.
For continued safety, replace with a lamp of the same type. Do not drop a lamp or touch a glass bulb! The glass can shatter and may cause injury.
Allow a projector to cool for at least one hour before you open the Lamp Cover. The inside of the projector can become very hot.
CAUTION
Unplug the AC power cord. Let the projector cool for at least one hour.
Loosen the three (3) screws that secure the lamp. Lift the lamp out of the projector by using the handles.
1
3
Replace the lamp with a new one and secure the three (3) screws. Make sure that the lamp is set properly. Close the lamp cover and secure the screw.
4
Loosen the screw and open the lamp cover.2
Connect the AC power cord to the projector and turn on the projector.5
Lamp	Replacement
CAUTION
Top	Control
LAMP REPLACE indicator
Screw
Handles
Screw
Lamp Cover
Screw
Screw
CAUTION
When replacing the lamp because it has stopped illuminating, there is a \
possibility that the lamp may be broken.If replacing the lamp of a projector which has been installed on the cei\
ling, you should always assume that the lamp is broken, and you should stand to the side of the lamp cover, not underneath it. Remove the lamp cover gently. Small pieces of glass may fall out when the lamp cover is opened. If p\
ieces of glass get into your eyes or mouth, seek medical advice immediately.
Note:
  • The Lamp replacement icon will not appear when the Display function is set to Off (p.53), during Freeze (p.8), or Blank (p.9).
Lamp	replacement	iconOK
POWER
AUTO SET
MENU
LAMP REPLACE
WARNING
VOLVOL
Reset	the	lamp	counter.See "Lamp Counter" on page 6.6
Lamp 
						

							
Maintenance	and	Cleaning

69

Maintenance	and	Cleaning

This  projector  uses  a  high-pressure  lamp  which  must  be  handled  carefully  and properly.  Improper handling may result in accidents, injury, or create a fire hazard.
●�amp life may differ from lamp to lamp and according to the environment of use.  Lamp  life  may  differ  from  lamp  to  lamp  and  according  to  the  environment  of  use. There  is  no  guarantee  of  the  same  life  for  each  lamp.  Some  lamps  may  fail  or terminate their life in a shorter period of time than other similar lamp\
s.
●  If the projector indicates that the lamp should be replaced, i.e., if the �AMP If the projector indicates that the lamp should be replaced, i.e., if t\
he LAMP REPLACE indicator lights up, replace the lamp with a new one IMMEDIATELY after the projector has cooled down.     (Follow  carefully  the  instructions  in  the  Lamp  Replacement  section  of  this  manual.) Continuous  use  of  the  lamp  with  the  LAMP  REPLACE  indicator  lighted  may increase the risk of lamp explosion.  
●  A �amp may explode as a result of vibration, shock or degradation as a result of  A  Lamp  may  explode  as  a  result  of  vibration,  shock  or  degradation  as  a  result  of hours  of  use  as  its  lifetime  draws  to  an  end.  Risk  of  explosion  may  differ  according to the environment or conditions in which the projector and lamp are bei\
ng used.
IF	A	LAMP 	EXPLODES,	THE	FOLLOWING	SAFETY 	PRECAUTIONS	SHOULD	BE	TAKEN.
If a lamp explodes, disconnect the projector’s AC plug from the AC outlet immediately. Contact an authorized service center for a checkup of the unit and replacement of the lamp. Additionally, check carefully to ensure that there are no broken shards or pieces 
of  glass  around  the  projector  or  coming  out  from  the  cooling  air  circulation  holes. Any broken shards found should be cleaned up carefully. No one should check the inside of the projector except those who are authorized trained technicians and who are familiar with projector service. Inappropriate attempts to service the unit by anyone, especially those  who  are  not  appropriately  trained  to  do  so,  may  result  in  an  accident  or  injury caused by pieces of broken glass.  
LAMP	HANDLING	PRECAUTIONS
ORDER	REPLACEMENT	LAMP
Replacement lamp can be ordered through your dealer.  When ordering a projection lamp, give 
the following information to the dealer.
 ●   Model	No.	of	your	projector	 :		LV-7290,	LV-7295,	LV-7390,	LV-8225
 ●   Replacement	Lamp	Type	No.	:		LV-LP35
CAUTION 
						

							
70
	 Problem: – Solutions
	 No	power  – Plug the power cord of the projector into the AC outlet.     – See if the POWER indicator lights red.     –  Wait until the POWER indicator stops blinking to turn on the projector again. The projector can be turned on after the POWER indicator turns red. See page 1.    – Check the WARNING indicator. If the WARNING indicator lights       red, projector cannot be turned on. See page 70.     – Check the projection lamp. See page 68.     – Unlock the Key lock function for the projector. See page 60.
The	initial	display	is	not	shown.			– Make sure Off or Countdown	off are not chosen at display      function. See page 53.
The	initial	display	is	not	same						– Make sure User or Off are not chosen at Logo (select)as	the	default	set.																													function. See page 53.
Input	signal	switches	automatically.    – Make sure Auto input function is adjusted properly.  (or	does	not	switch	automatically)	         See page 5.
When	the	projector	is	on	and					    – That is the Filter warning icon. See page 60.you	press	the	input	source		buttons,	an	icon	other	than	the	Lamp	mode	icon	appears.
An	icon	other	than	Input	mode			  – That is the Lamp replacement icon or the Filter warning icon.   or	Lamp	mode	icon	appears.											See page 68 or 60.
Image	is	out	of	focus.  – Adjust focus of the projector. See page 6.     – Provide proper distance between the projector and the         projection screen. See page 15.     – Check the projection lens to see if it needs cleaning.      See page 67.     – Moving the projector from a cool to warm place may result in         moisture condensation on the projection lens. In such cases,      leave the projector off and wait until condensation evaporates.
Image	is	Left/Right	reversed.  – Check the Ceiling/Rear function. See pages 38,40,48,50. Image	is	Top/Bottom	reversed.  – Check the Ceiling function. See pages 38,40,48,50. Picture	is	not	bright	enough.	– Check if the Contrast or Brightness is adjusted properly.                                                              See pages 36\
, 45.    – Check if Image	mode is selected properly. See pages 35,44.   – Check the Lamp mode function. See pages 8, 59.   – Check the LAMP REPLACE indicator. If it lights, the end of lamp      life is approaching. Replace the lamp with a new one promptly.                                                             See page 68.\
Before calling your dealer or service center for assistance, check the i\
tems below once again.–  Make  sure  you  have  properly  connected  the  projector  to  peripheral  equipment  as  described  on pages 17-19. – Make sure all equipment is connected to AC outlet and the power is turned on.– When the projector does not project an image from the connected computer\
, restart the computer.  
Appendix
Troubleshooting