Canon projector LV7290 User Manual

11

Part	Names	and	Functions
‰
(MIC)-
Rear	Terminal	
②③①
⑥
⑤
⑧
④
④   VIDEO	IN  Connect the composite video output signal to this jack (p.18).
②  COMPUTER	IN	1	/S-VIDEO	IN	/	COMPONENT	IN Connect output signal from a computer, component video output, RGB scart 1-pin video output or S-VIDEO output to this terminal (pp.17-19).
⑥  AUDIO	OUT	(VARIABLE) Connect an external audio amplifier to this jack (pp.17-19). This terminal outputs sound from AUDIO IN terminal.       Never plug headphones into this...

1

Part	Names	and	Functions

Top	Control
⑦  LAMP	REPLACE	indicator Lights yellow when the projection lamp reaches its end of life (pp.68, 75).
⑧  WARNING	indicator – Lights red when the projector detects an abnormal condition.   – Blinks red when the internal temperature of the projector exceeds the operating range (pp.65, 75).
④  POWER	buttonTurn the projector on or off (pp.1-3).
⑤  POWER	indicator  – Lights red when the projector is in stand-by mode.  – Lights green during operations....

Part	Names	and	Functions

13

Part	Names	and	Functions

Note:To ensure safe operation, please observe the following precautions:– Do not bend, drop or expose the remote control unit to moisture or heat.– For cleaning, use a soft dry cloth. Do not apply benzene, thinner, spray, or any chemical material.
Remote	Control	Unit
⑦
⑭⑩
⑳④
⑱
②
⑧
⑨
⑬
⑯
⑤
⑥
⑪
⑫
⑲
⑮
③
② AUTO	SET	button
Execute the setting of Auto setup (includes Auto input, Auto PC and Auto Keystone functions) in the setting menu. (pp.6,...

14

Part	Names	and	Functions
To ensure safe operation, please observe the following precautions : ● Use two (2) AAA type batteries. ● Always replace batteries in sets. ● Do not use a new battery with a used battery. ● Avoid contact with water or liquid. ● Do not expose the remote control unit to moisture or heat. ● Do not drop the remote control unit. ● If the battery has leaked on the remote control unit, carefully wipe the case clean and install new batteries. ● Risk of an explosion if battery is...

Part	Names	and	Functions
15
Positioning	the	Projector
For projector positioning, see the figures below. The projector should be set perpendicularly to the plane of the screen.
Installation
Note:
 • The  brightness  in  the  room  has  a  great  influence  on  picture  quality.  It  is  recommended  to  limit ambient lighting in order to obtain the best image. • All measurements are approximate and may vary from the actual sizes.
A
B
100
150
200250
167
125
83
300(wide)
40
300(tele)
Max. ZoomMin. Zoom...

16

Installation

Adjustable	Foot
Adjustable FootFoot Lock Latch
Projection  angle  can  be  adjusted  up  to  10.0  degrees with the adjustable foot. 
Lift  the  front  of  the  projector  and  push  the  foot  lock latch on the projector.
Release  the  foot  lock  latch  to  lock  the  adjustable  foot and  rotate  the  adjustable  foot  to  adjust  the  position and tilt.
To  retract  the  adjustable  foot,  lift  the  front  of  the projector and push and undo the foot lock latch.
Keystone...

Installation

17

Installation

Connecting	to	a	Computer
Note:Unplug the power cords of both the projector and external equipment from the AC outlet before connecting cables.
Note:•When the MIC function is set to Off	in the Sound menu, the MIC function is disabled.•When MIC  is  set  to On  in  Sound  Menu, AUDIO  IN  (PC/MIC)  and AUDIO  IN(L/R)  terminals  can be  connected  at  the  same  time. At  this  time, AUDIO  IN  (PC/MIC)  termianl  as  MIC  input, AUDIO IN(L/R) terminal as COMPUTER or...

18

Installation

Connecting	to	VIDEO	Equipment
(MIC)-
External Audio Equipment
Audio cable   (stereo)
S-VIDEO cable  
Audio Output
S-VIDEO Output  
Audio Input
AUDIO IN(PC or MIC)
S-VIDEO-VGA cable  
VIDEO cable   
COMPUTER  IN 1/ S-VIDEO IN/COMPONENT IN
VIDEO IN
Audio cable   (stereo)
AUDIO OUT (stereo)
AUDIO IN
Audio cable   (stereo)
Cables	used	for	connection		• VIDEO Cable • S-VIDEO Cable • S-VIDEO-VGA Cable • Audio Cables(Cables are not supplied with the projector. )
Note:• When the MIC function...

Installation

19

Installation

(MIC)-

Connecting	to	COMPONENT	VIDEO	and	SCART	Equipment
External Audio Equipment
AUDIO IN
Audio cable (stereo)
Audio Input
COMPONENT VIDEO Output(Y, Pb/Cb, Pr/Cr)Audio OutputRGB Scart 1-pin Output
Scart-VGA cable 
COMPONENT-     VGA cable
AUDIO OUT (stereo)
COMPONENT cable
COMPUTER IN 1/ S-VIDEO IN / COMPONENT IN 
Cables	used	for	connection		• Audio Cables • Scart-VGA Cable • COMPONENT Cable • COMPONENT-VGA Cable (Cables are not supplied with this projector.)...

0

Installation
Connecting	the	AC	Power	Cord
This projector uses nominal input voltages of 100-40 V AC and it automatically selects the correct input voltage. It is designed to work with single-phase power systems having a grounded neutral conductor. To reduce the risk of  electrical  shock,  do  not  plug  into  any  other  type  of power system.If  you  are  not  sure  of  the  type  of  power  being  supplied, consult your authorized dealer or service center.Connect  the  projector  with...