Canon projector LV7220 User Manual
Have a look at the manual Canon projector LV7220 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1335 Canon manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
21 Basic Operation Basic Operation Press the POWER button on the top control or on the remote control unit, and a message Power off? appears on the screen. Press the POWER button again to turn off the projector. The POWER indicator starts to blink red, and it continues while the cooling fans are operating for about 90 seconds. (About 120 seconds when the fan mode is L2. See page 48.) 1 2 TO MAINTAIN THE LIFE OF LAMP, ONCE YOU TURN PROJECTOR ON, WAIT AT LEAST 5 MINUTES BEFORE TURNING IT OFF. DO NOT DISCONNECT AC POWER CORD WHILE COOLING FANS ARE RUNNING OR BEFORE POWER INDICATOR LIGHTS RED. OTHERWISE IT WILL RESULT IN SHORTENING LAMP LIFE. 3When the projector has cooled down enough to be turned on again, the POWER indicator lights red. Then you can disconnect the AC power cord. The message disappears after 4 seconds. ✔Note: • The projector cannot be turned on during the cooling period with the POWER indicator blinking red. You can turn it on again after the POWER indicator lights red. • When the On start function is on, this projector is turned on automatically by connecting the AC power cord to an AC outlet. (See page 45 for the On start function.) • Do not operate the projector continuously without rest. Continuous use may result in shortening the lamp life. Turn off the projector and give it a rest about an hour in every 24 hours. • This projector monitors internal temperature and automatically controls the running speed of the cooling fans. • If the WARNING indicator blinks or lights red, see “Warning Indicator” on page 49. Turning Off the Projector
22 Basic Operation INPUT LA MENU AUTO SET SETVOL VOL + - Top Control Menu bar Pointer (red frame) Menu icon Item data Press the Point 7 8buttons to adjust value. SET button Pointer (red frame) Press the Point dbutton to move the pointer. Item How to Operate the On-Screen Menu MENU button SET buttonPOINT button (outer ring) On-Screen Menu Quit to exit this menu. The projector can be adjusted or set via the On-Screen Menu. Refer to the following pages regarding each adjustment and setting procedure. Press the Point 7 8buttons to select a Menu icon to adjust. Press the Point edbuttons to select an item to adjust. Press the SET button to show the item data. Press the Point 7 8 buttons to adjust the data. Refer to the following pages for respective adjustment. Press the MENU button to display the On-Screen Menu. ✔Note: The selected item is not in effective until the SET button is pressed. 1 2 3 SET button POINT button Remote Control Unit MENU button
23 Basic Operation Basic Operation Menu Bar PC System Menu Used to select computer system. (p28) Image Adjust Menu Used to adjust computer image. [Contrast / Brightness / Color temp. / White balance (R/G/B) /Sharpness / Gamma](p33) Setting Menu Used to change settings of the projector or reset lamp replace counter. (p42-48) Sound Menu Used to adjust volume or mute sound. (p26) Image Select Menu Used to select an image level among Standard, High contrast, Blackboard(Green), and Custom. (p32) For computer source AV System Menu Used to select system of selected video source. (p37) Image Adjust Menu Used to adjust picture image. [Contrast / Brightness / Color / Tint / Color temp. / White balance (R/G/B) / Sharpness /Gamma / Progressive / Film] (p39-40) For video source Same function as menu for computer source. Input Menu Used to select input source either Video or Computer. (p35-36) PC Adjust Menu Used to adjust parameters to match with input signal format. (p29-31) Image Select Menu Used to select an image level among Standard, Cinema, Blackboard(Green) and Custom. (p38) Screen Menu Used to set size of image to Normal or Wide. (p41) Guide Window Shows the selected Menu of the On- Screen Menu. Same function as menu for computer source. Input Menu Used to select input source either Computer or Video. (p27) Screen Menu Used to adjust size of image. [Normal / True / Wide / Digital zoom +/–] (p34)
24 Basic Operation Rotate the Zoom Lever to zoom in and out. Rotate the Focus Ring to adjust the projected picture focus. Zoom Lever Focus Ring Auto Setup Function Auto setup function is provided to automatically correct Keystone distortion according to the projectors tilt and adjust the computer display parameters (Fine sync, Total dots and Picture position) by just pressing the AUTO SET button on the top control or on the remote control unit. The operational setup for the Auto setup can be changed in the Setting menu. Refer to p42 on setting of the Auto setup function. ✔Note:. • Auto Keystone corrects vertical distortion only, not correct horizontal distortion. •Auto Keystone cannot work when Ceiling feature is On in the Setting menu. (p44) •Perfect correction of the image distortion cannot be ensured with the Auto setup function. If the distortion cannot be corrected properly by pressing the AUTO SET button, adjust manually by pressing the KEYSTONE button on the remote control unit or selecting Keystone in the Setting menu. (p25, 42) INPUT L MENU AUTO SET SETVOL VOL + - Top Control AUTO SET button AUTO SET button Remote Control Unit Zoom and Focus Adjustment
25 Basic Operation Basic Operation Press the FREEZE button on the remote control unit to freeze the picture on the screen. To cancel FREEZE, press the FREEZE button again. (p11) If a projected picture still has keystone distortion after pressing the AUTO SET button on the top control or on the remote control unit, correct the image manually as follows: •The arrows are blue when there is no correction. •The arrows disappear at the maximum correction. •The direction of the arrow being corrected turns light blue. •If you press the KEYSTONE button on the remote control unit once more while the keystone dialog box is being displayed, the keystone adjustment will be canceled. 1Press the KEYSTONE button on the remote control unit or select Keystone in the Setting Menu (p42). The keystone dialog box appears. 2Correct keystone distortion by pressing the Point e ed d 78 button. Keystone adjustment can be memorized. (p42) Reduce the upper width with Point e e button. Reduce the lower width with Point d d button. Reduce the left part with Point 7button. Reduce the right part with Point 8button. Press the NO SHOW button on the remote control unit to black out the image. To restore to normal, press the NO SHOW button again. When a projected image is captured and set as “User” in the Logo item in the Setting Menu (p44), the screen changes each time you press the NO SHOW button as follows. The message disappears after 4 seconds.black out ➜the captured image ➜normal ➜• • • • • No Show Function Picture Freeze Function Keystone Adjustment ✔Note:. • When correcting the keystone distortion, resolution of the image changes. Because of that, the projected words or lines could not be shown exactly the same as original ones. • When adjusting keystone distortion manually, set Auto keystone menu Off in the Autosetup function.
26 Basic Operation 1 2 Press the MENU button and the On-Screen Menu will appear. Press the Point 7 8button to move the red frame pointer to the Sound Menu icon. Volume Press the VOL (+/–) button on the top control or on the remote control unit to adjust volume. The volume dialog box appears on the screen for a few seconds. (+) button to turn up the volume and (–) button to turn down the volume. Mute Press the MUTE button on the remote control unit to cut off sound. To restore sound to its previous level, press the MUTE button again or press the VOL (+/–) button. Press the Point 8button to turn up the volume, and press the Point 7button to turn down the volume. Press the Point 7 8button to cut off sound. Dialog box display is changed to “On” and sound is cut off. To restore sound to its previous level, press the Point 7 8button again. Press the Point d dbutton to move the red frame pointer to the item that you want to select, and then press the SET button. indicates approximate level of volume. closes the Sound Menu. Direct Operation Volume Mute indicates approximate level of volume. Press the MUTE button to set the Mute function On or Off. The display disappears after 4 seconds. Sound Menu Sound Menu icon Sound Adjustment Menu Operation Press the P-TIMER button on the remote control unit. The timer display “00 : 00” appears on the screen and the timer starts to count time (00 : 00 ~ 59 : 59). To stop the P-Timer, press the P-TIMER button. And then, press the P-TIMER button again to cancel the P-Timer function. P-Timer Function
27 Choose either Computer 1 or Computer 2 by pressing the INPUT button on the top control or press the COMPUTER button on the remote control unit. Before using these buttons, correct input source should be selected through menu operation as described below. Press the MENU button and the On-Screen Menu will appear. Press the Point 7 8button to move the red frame pointer to the Input Menu icon.1 Computer 1 Input Menu Press the Point d d button to move the red arrow pointer to either Computer 1 or Computer 2, and then press the SET button. 2 After the Source Select Menu appears for Computer 1, move the pointer to RGB and then press the SET button.3 Input Menu Computer 1 Video Computer 2 COMPUTER button Computer 1 Computer 2 When the input source is analog coming from a computer through the DVI terminal, select RGB (Analog). RGB (Analog) INPUT button Input Source Selection Direct Operation Menu Operation Computer Input ✔Note: •Computer 2 is not displayed when the RGB IN-2/ COMPONENT IN/ RGB OUT terminal is set as Monitor out. (p44) •HDCP (High-bandwidth Digital Content Protection) is a system for protecting digital entertainment content delivered by DVI (Digital Visual Interface) from being copied. The specification of HDCP is decided and controlled by Digital Content Protection, LLC. Should the specification be changed, this projector may not display the digital content protected by HDCP. Move the pointer (red arrow) to Computer 1 and press the SET button. Input Menu icon Move the pointer (red arrow) to Computer 2 and press the SET button. ✳See Note on the bottom of this page. ✳ ✳ Move the pointer to RGB(Analog), RGB (PC Digital), or RGB(AV HDCP) and press the SET button. Source Select Menu Move the pointer to RGB and press the SET button. Source Select Menu Computer 2 When the input source is digital coming from a computer through the DVI terminal, select RGB (PC Digital)RGB (PC Digital) When the input source is analog coming from a computer through the RGB IN-2/ COMPONENT IN/ RGB OUT terminal, select RGB. RGB When the input source compatible with HDCP is coming from video equipment through the DVI terminal, select RGB (AV HDCP). RGB (AV HDCP) ✳See Note on the bottom of this page. Computer Input
28 Computer Input The Auto PC Adjustment function operates to adjust the projector. PC System Menu The PC System Menu icon displays the system being selected. The systems on this dialog box can be selected.Press the MENU button and the On-Screen Menu will appear. Press the Point 7 8buttons to move the red frame pointer to the PC System Menu icon. Press the Point d d button to move the red arrow pointer to the system that you want to set, and then press the SET button. 1 2 PC System Menu Custom Mode (1~5) set in the PC Adjust Menu. (p30, 31) PC system can also be selected manually. Computer System Selection This projector automatically tunes to various types of computers based on VGA, SVGA, XGA or SXGA with its Multi-scan system and Auto PC Adjustment. If Computer is selected as a signal source, this projector automatically detects the signal format and tunes to project a proper image without any additional setting. (Signal formats provided in this projector is shown on page 59 ) When the projector cannot recognize connected signal conforming to PC Systems provided in this projector, Auto PC Adjustment function works to display proper images and the message “Auto” is displayed on the PC System menu box. When the image is not projected properly, manual adjustment is required. (p30, 31) There is no signal input from computer. Check the connection of your computer and the projector. (See Troubleshooting p54) Auto ----- ✔Note: The projector may display one of the following messages. User preset system manually adjusted in PC Adjust menu. Adjustment data can be stored in Mode 1 - 5. (p30, 31) Mode 1 PC Systems provided in the projector. The projector chooses a proper system and displays it. SVGA 1 Selecting Computer System Manually *Mode 1 and SVGA 1 are examples.
29 Computer Input Auto PC Adjustment function is provided to automatically adjust Fine sync, Total dots, Horizontal, and Vertical to conform to your computer. Auto PC Adjustment function can be operated as follows. Move the red frame pointer to the Auto PC Adj. icon and press the SET button. PC Adjust Menu PC Adjust Menu icon To store adjustment parameters Adjustment parameters from Auto PC Adjustment can be memorized in this projector. Once parameters are memorized, the setting can be done just by selecting Mode in the PC System Menu (p28). See “Store” on page 31. ✔Note: • Fine sync, Total dots and Picture Position of some computers can not be fully adjusted with this Auto PC Adjustment function. When the image is not provided properly with this operation, manual adjustments are required. (p30, 31) • The Auto PC Adjust cannot be operated when 480i, 575i, 480p, 575p, 720p,1035i, or 1080i is selected in the PC System Menu. (p28) Auto PC Adjustment Press the MENU button to display the On-Screen Menu. Press the Point 7 8button to move the red frame pointer to PC Adjust Menu icon.1 2Press the Point dbutton to move the red frame pointer to Auto PC Adj. icon and then press the SET button twice. This Auto PC Adjustment can be also executed by pressing the Auto PC button on the remote control unit. Auto PC Adj. Computer Input
30 Computer Input Press the MENU button and the On-Screen Menu will appear. Press the Point 7 8button to move the red frame pointer to the PC Adjust Menu icon.1 2Press the Point d dbutton to move the red frame pointer to the item that you want to adjust and then press the SET button. An adjustment dialog box will appear. Press the Point 7 8button to adjust value.Move the red frame pointer to an item and press the SET button. PC Adjust Menu PC Adjust Menu icon Eliminates flicker from the image displayed. Press the Point 7 8 button to adjust value. (From 0 to 31)Fine sync Adjusts the number of total dots in one horizontal period. Press the Point 7 8button and adjust number to match your PC image. Total dots Adjusts horizontal picture position. Press the Point 7 8button to adjust the position.Horizontal Adjusts vertical picture position. Press the Point 7 8button to adjust the position.Vertical Press the SET button to show H-Freq. and V-Freq. of the connected computer. Current mode Adjusts clamp level. When the image has dark bars, try this adjustment.Clamp Press the SET button at this icon to adjust the other items. Press the Point 7 8button to adjust the value.Shows status (Stored / Free) of the selected Mode. Selected Mode Press the SET button at the Current mode icon to show the information of the connected computer. Current mode Manual PC Adjustment Some computers employ special signal formats which may not be tuned by Multi-scan system of this projector. Manual PC Adjustment enables you to precisely adjust several parameters to match those signal formats. The projector has 5 independent memory areas to memorize those parameters manually adjusted. It allows you to recall the setting for a specific computer.