Canon projector LV7215 User Manual

11
Part Names and Functions
INPUTWARNING
LAMP REPLACE 
MENU
 POWER
  KEY
STONESETVOL VOL
+ -
This projector has control buttons and indicators on its top.
To p
qwr
tyui
uLAMP REPLACE indicator
Turns yellow when the life of the projection lamp draws to an
end.  (p43)
iWARNING indicator
Lights red when the projector detects abnormal condition.  This
also flashes red when the internal temperature of the projector
exceeds the operating range.  (p41)
rPOWER ON–OFF button
Turns the projector on or off.  (p19)...

12
Part Names and Functions
Remote Control Unit
q
w
e
r
t
y
u
i
o
!0
!1
!4
!5
!6
!7
!8
!9
@0!2
!3@1
@1RESET/ON/ALL-OFF switch
When using the remote control, set this switch to “ON.” Set it to “ALL OFF” when
it is not used for energy saving.  Slide this switch to the RESET to initialize the
remote control code.  (p14)
wSIGNAL EMISSION indicator
The indicator lights red while the laser beam is being emitted from the Laser Light
Window or a signal is being sent from the remote control to the projector....

13
Part Names and Functions
You can move Spotlight or Pointer of the projector with the remote control unit to emphasize a part of the projected image.
(See “Pointer” on page 40 for changing the patterns and sizes.)
While pressing the MENU button, hold down the NO SHOW
button for more than 7 seconds so that the Pointer function
can be available. (The Laser pointer function has switched to
the Pointer function.)1
Spotlight
Press the LASER button on the remote control unit toward
the projector and see if...

14
Part Names and Functions
This projector has eight different remote control codes (Code 1-Code 8); the factory-set, initial code (Code 1) and the other
seven codes (Code 2 to Code 8).  This switching function prevents remote control unit interference when operating several
projectors or video equipment at the same time.  (Change the remote control code for the projector first before changing
that for the remote control unit.  See “Remote control” on page 40.) 
While pressing the MENU button, press the...

15
Part Names and Functions
To guarantee safe operation, please observe the following precautions :
Use (2) AA, UM3 or R06 type alkaline batteries.
Replace two batteries at the same time.
Do not use a new battery with a used battery.
Avoid contact with water or liquid.
Do not expose the remote control to moisture, or heat.
Do not drop the remote control.
If a battery has leaked on remote control, carefully wipe case clean and install new batteries.
Risk of explosion if battery is replaced by an...

16
Installation
Projection angle can be adjusted up to 11.9 degrees with the adjustable feet. 
Lift the front of the projector and pull the feet lock latches on
both sides of the projector.1
Adjustable Feet
Feet Lock Latches
Release the feet lock latches to lock the adjustable feet and
rotate the adjustable feet to adjust the position and tilt. 2
To retract the adjustable feet, lift the front of the projector
and pull and undo the feet lock latches.
Keystone distortion of the projected image can be...

17
Installation
Connecting to a Computer
    AUDIO 
R      IN      L VIDEO  IN    DVI-I/
RGB IN-1
SERVICE PORT S-VIDEO IN
 COMPUTER
  AUDIO IN
 AUDIO OUT
            RGB IN-2/
COMPONENT IN/
            RGB OUT
RESET
MCI
ON ON
ON
1DIPON
OFF
23456
13 MODE (640 x 480)
16 MODE (832 x 624)
19 MODE (1024 x 768)OFF
ON
ONOFF OFF OFF
OFF OFF OFF
OFF OFF OFF34 56
OFF OFF ON ON 21 MODE (1152 x 870)
ON ON
ON
ON OFF
OFF12
ON ON
IBM-compatible computer or Macintosh computer (VGA / SVGA / XGA / SXGA)
DVI-VGA Cable...

18
Installation
Connecting to Video Equipment
    AUDIO 
R      IN      L VIDEO  IN    DVI-I/
RGB IN-1
SERVICE PORT S-VIDEO IN
 COMPUTER
  AUDIO IN
 AUDIO OUT
            RGB IN-2/
COMPONENT IN/
            RGB OUT
RESET
MCI
Video Source (example)
Video Cassette RecorderDigital Camcorder
S-VIDEO
Cable 
✽
Audio AmplifierAudio Speaker 
(stereo) Audio Cable 
(Stereo) 
✽
Terminals 
of the Projector
S-VIDEO
Output
Audio Input
• Video Cable (RCA x 1) ✽
• S-VIDEO Cable ✽
• Audio Cables (Mini Plug (stereo) x 2...

19
Basic Operation
Connect the projectors AC power cord into an AC outlet.  The
POWER indicator flashes red in a moment and turns on red. 
Press the POWER ON-OFF button on the top control or on the
remote control unit.  The POWER indicator turns green, and the
cooling fans start to operate.  The preparation display appears on
the screen and the count down starts. 
2
3
Press the POWER ON-OFF button on the top control or on the
remote control unit, and a message Power off? appears on the
screen.  
Press...

20
If a projected picture has keystone distortion, correct the image with KEYSTONE adjustment.
Basic Operation
•The arrows are blue when there is no correction.
•The arrows disappear at the maximum correction.
•The direction of the arrow being corrected turns light
blue.
•If you press the KEYSTONE button on the top control
or on the remote control unit once more while the
keystone dialog box is being displayed, the keystone
adjustment will be canceled.
Keystone Adjustment
Zoom Adjustment
Focus...