Canon printer PIXMA SELPHY CP510 User Manual

							
29
Printed or fed paper is coated even when nothing is printed on the paper. Therefore, 
never reuse the printed or fed paper for printing. Reused paper may stick to the ink 
sheet, resulting in damage to the printer.
„Loading the Paper Cassette
Do not remove the paper cassette while feeding, printing, or ejection is in progress.
3Place the middle cover back to its 
original position.
zAfter pulling the middle cover down, slide it in 
the direction of the arrow until it clicks back into 
place.
zDo not close the top cover.
1Open the paper cassette 
compartment cover.
2Push the paper cassette all 
the way into the paper 
cassette slot.
zBe sure the paper is set correctly 
before pushing the cassette in.
zInsert the paper cassette evenly so 
that it slides over the bottom of the slot 
entrance.
The printer outputs the finished prints into 
the receptacle onto the top of the printer 
cassette (top of the middle cover or inside 
of the top cover). Be sure to close the 
middle cover and open the top cover so 
that output can proceed normally.
 Do not allow more than 9 sheets to 
accumulate in the print receptacle. Do not 
allow too many prints to accumulate.
Top cover open
Middle cover 
closed
Print receptacle  
						

							
30
„Placing the Printer
Usage Location   Usage Location (p. 14)
Refer to the figure below when placing the printer. Numbers in the figure correspond to 
the steps in the procedure below.
The battery pack (sold separately) also can be used (p. 55).
1Place the printer on a flat area.
2Connect the supplied power cord to the supplied Compact Power 
Adapter CA-CP200.
3Insert the plug in a power outlet.
4Connect the compact power adapter cable to the printer.
To power outletCompact power 
adapter
15 cm (6 in.) at the front and 
back of the device 
and 10 cm (4 in.) on both sides 
or more of open space
1
2
3
4  
						

							
31
Connecting to a Camera for Printing
Connecting to a Camera for Printing
Connect the printer to the camera by the built-in retractable USB cable and start printing. 
This section explains the flow of printing operations with Canon cameras*. 
For more details, refer to your  Camera User Guide or Direct Print User Guide .
*In other cases, please refer to the  Printing with Non-Canon Digital Cameras (p. 66) .
Make sure that the memory card is not inserted into the printer and that the printer is not 
connected to the computer.
zUse Canon cameras compatible with CP710/CP510, and non-Canon cameras compatible 
with  PictBridge  can also be connected.
zWe recommend that you also connect the camera’s compact power adapter (sold 
separately or included with the camera) when using the camera with your printer. If you 
wish to run the camera on battery pack or batteries power, be sure that battery pack is 
fully charged or the bat teries are fresh. 
zSome camera models do not come with a compact power adapter. For details, please see 
the System Map  that came with your camera.
1Pull out the retractable USB cable 
from the printer, and connect to the 
camera.
zYou can also use the USB cable included 
with the camera. In this case, connect the 
DIGITAL terminal on the camera to the direct 
print port (p. 20, 21).
zTo retract the USB cable, pull the cable 
gently towards you and release the cable.
zThe cable can be pulled out up to about 25 cm 
(9.8 in.). Note that pulling the cable out 
beyond this length may damage it.
2Press the printer’s power button.
zThe power button lights green once the printer powers up.
3Turn the camera’s power on and 
display the images.
zCheck that the  (PictBridge ) /  (Canon 
Direct Print )
 icon is displayed in the upper left 
corner of the LCD monitor. 
When the icon is not displayed    Troubleshooting 
(p. 58)
zSome camera models automatically power up when 
the cable is connected to the printer. The icon then 
displays on the LCD monitor.  
						

							
32
„Disconnect the camera
Before you disconnect the camera from the printer, turn off the printer by holding down 
the power button until the green indicator goes out. 
„Printing on the separately sold wide size (100 x 200 mm 
(4 x 8 in.)) paper
The printing area may vary depending on the camera use.
If   appears in step 3 on page 31, select [Default] on the paper size setting screen.
4Display the images to be printed and press the SET or SELECT 
button.
zIf your camera has a  (Print/Share) or  (Direct print) button, printing starts 
immediately after you press the   or   button (Step 5 is not necessary).
5Select [Print] and press the SET or 
SELECT button.
zPrinting starts. During printing, the printer’s power 
button blinks green.
zThe camera returns to the playback screen once 
printing is successfully completed.
If printing does not start, check the camera’s LCD 
monitor for any messages (p. 61).The screen shot differs depending 
on the model of your camera.
If  appears in step 3 on page 31
Printed on the 100 x 150 mm (4 x 6 in.) 
portion of the card.If  appears in step 3 on page 31
Printed on the whole card.
Nothing is printed on this portion 
so you can write your message with an oil-based 
pen. 
The upper and lower portions of an image 
are trimmed.  
						

							
33
Printing from Memory Card (CP710 only)
Insert the memory card into the printer so that you can print images stored on the 
memory card.
Make sure that the camera or computer is not connected to the printer. 
Clearer printing results can be obtained when printing from a memory card by optimizing the 
information stored in the camera when the photo was taken. 
To turn image optimization off, press and hold the DATE button and then press the PRINT/
STOP button to start printing (p. 35).
Compatible Memory Cards
*1 Use the specific adapter for the card.
*2 Purchase the CompactFlash Card Adapter for xD-Picture Card separately.
zThis printer suppor ts images taken with a camera compatible with the Design rules for 
Camera File system (Exif compliant) and DPOF (ver 1.00 compliant).
zImages saved on non-compatible memory cards might not be able to be read or data may be 
corrupted. Use a memory card that is compatible with the camera. For details, refer to the 
camera’s user guide included with the camera. 
zFormat memory cards on the camera. Memory cards should not be formatted on computers.
zImages that have been edited on a computer might not be displayed or printed successfully.
Memory cards that can be directly insertedMemory cards that require a specific adapter
zSD memory card 
zMultiMedia Card
zminiSD card
zCompactFlashTM (CF) 
card
zMicrodrive
  *TYPEI/TYPEII (Only 3.3 V 
cards are compatible.)
zxD-Picture Card
zMemory Stick
zMemory Stick PRO
zMagic Gate Memory 
Stick
zMemory Stick Duo
zMemory Stick PRO Duo
zMagic Gate Memory Stick Duo
*1
*2
*1  
						

							
34
Inserting Memory Cards
Do not load two or more memory cards at the same time. 
Removing Memory Cards
As shown in the figure on the right, grip the protruding 
section of the card, and remove it from the card slot.
Do not remove memory cards or turn the printer off while the indicator lamp is blinking. 
1Press the printer’s power button.
zThe power button lights green once the printer powers up.
zAfter a while, the startup screen is displayed on the LCD monitor. 
2Push the memory card all the way into the card slots. 
zThe memory card will protrude slightly from the card slots.
zThe indicator lamp blinks green, and the images on the memory card are displayed on the 
LCD monitor. 
Insert memory cards with the label side up.
*The exclusive adapter is required (p. 33).
LCD monitor    Main Details Displayed on the LCD Monitor (p. 35)
CF card/
Microdrive/
xD-Picture Card
*
SD memory card/
Multimedia card/
miniSD card
*
Memory Stick/Memory Stick Duo*/
Memory Stick PRO/Memory Stick PRO Duo*/
Magic Gate Memory Stick/
Magic Gate Memory Stick Duo
*
Example:CF card  
						

							
35
About LCD Monitor and Operation Buttons
„Main Details Displayed on the LCD Monitor
Error screen   Error Messages (p. 61)
LCD Monitor
Displays images on the 
memory card, and details 
that have been set using 
the buttons.  button: Displays the 
previous image.
 button: Displays the next  image.
 button: Increments the  number of prints.
 button: Decrements the  number of prints.
PRINT/STOP Button
Starts printing. Printing is 
canceled when this button 
is pressed during printing. 
MODE Button
Selects the print 
operation mode.
SELECT
Printing Selected Images 
(p. 36).
ALL
Print all of the images on 
the memory card one 
image at a time (p. 37).
DPOF
Prints DPOF by specified 
images (DPOF) (p. 38)
LAYOUT Button
Selects the print layout 
(p. 39). 
Borderless
Bordered
8 stickers Index
The file No. can also be printed.
DATE Button
Selects whether or not 
to print the date that you 
took the photograph. 
When you print the date, 
specify the format of the 
date (p. 40).
The date is not 
printed.
Ye a r / M o n t h / Day
Month/Day/ Year
Day/Month/ Year
File No.
Selected image
Kind of ink cassette currently 
loaded in the printer
Layout setting
Current operation 
modeDate setting
Number of sheets to be printed
Number of prints of the currently 
displayed image
Print preview  
						

							
36
Printing Selected Images (SELECT)
Select a specific image in the LCD monitor and print that image. 
The required number of specific images can be printed together. 
Buttons available for this function
1Turn the printer on, and insert the memory card 
into the card slot (p. 34).
zThe   (SELECT) screen is displayed. If the   screen is 
not displayed, press the MODE button and display   .
zYou can specify the layout with the  LAYOUT button (p. 39).
zYou can print the date with the  DATE button (p. 40).
2Press the   button or the   button to display 
the image to print.
3Press the   button or the   button to specify 
the number of prints.
4Repeat steps 2 and 3.
To cancel printing of a specified image,  display the desired image, and press the   
button to set the number of prints to “0”. 
 button
 button
 button
 button
Number of prints  
						

							
37
Printing All Images (ALL)
Print a single copy of all the images on the memory card at a time. 
5Check the setting on the LCD monitor.
Make sure that the paper cassette contains the 
required number of sheets of paper.
6Press the PRINT/STOP button.
zPrinting starts. During printing, the printer’s power button blinks green.
Buttons available for this function
1Turn the printer on, and insert the memory card into the card slot 
(p. 34).
2Press the MODE button to display  (ALL).
zYou can specify the layout with the LAYOUT button (p. 39).
zYou can print the date with the  DATE button (p. 40).
3Check the setting on the LCD monitor.
Make sure that the paper cassette contains the 
required number of sheets of paper.
4Press the PRINT/STOP button.
zPrinting starts. During printing, the printer’s power button blinks green.
Print preview (when 8 
stickers are specified in 
LAYOUT (p. 39))
Number of sheets to be printed
Print preview 
(when 8 stickers are specified in LAYOUT (p. 39))  
						

							
38
Printing by specified camera settings (DPOF)
You can make prints according to the DPOF (Digital Printer Order Format) setting 
specified on the camera.
zThe date setting complies with the DPOF information. The date cannot be set with the 
DATE button.
zLayout cannot be specified.
Buttons available for this function
1Turn the printer on, and insert the memory card into the card slot 
(p. 34).
2Press the MODE button to display  (DPOF).
z(DPOF) cannot be selected when a DPOF-specified image is not found on the 
memory card.
Make sure that the paper cassette contains the required number of sheets of paper.
3Press the PRINT/STOP button.
zPrinting starts. During printing, the printer’s power button blinks green.
The “Print type” set on the camera is displayed. 
Both:  Standard:  Index: