Canon printer PIXMA Pro9000 Mark II User Manual

Make sure to read this manual before using the printer. Please keep it in hand for future reference.
Getting Started
Read Me First
series
Photo Printer 

Contents
6
After Installing the Printer
Install the Software
5
Install the Ink Tanks4
Install the Print Head3
Turn the Power On2
Loading Paper
Preparation
1 


S y m b o l s
■
The following symbols are used to mark important instructions. Observe t\
hese instructions.
Additional explanations. Instructions that, if ignored, could result in personal injury or materi\
al damage.
Instructions that must be observed for safe operation.
Model Number: K10335 (Pro9000 Mark II)
Macintosh and Mac are trademarks of Apple Inc., registered in the U.S. and other countries.
•
Descriptions for operations that take some time to complete.
Microsoft is a registered trademark...


1
Preparation
C h e c k   t h e   I n c l u d e d   I t e m s
■
Manuals• ink tanks
Print Head
Before turning on the printer, remove all the orange tapes and the protective sheets.
Setup CD-ROM (containing the drivers, applications and on-screen manual\
s)
•
Warranty
• power cord
A USB cable is necessary to connect the printer with your computer.
• 


612 3 4 5
Place the printer on a flat surface.
•
Do not place any object in front of the printer.
•
You can print on large size paper such as 14" x 17"/355.6 x 431.8 mm or thick paper by loading the 
paper in the Front Tray. In that case, keep a space of 15.7"/40 cm behind the printer.
•
C h o o s i n g   a   L o c a t i o n
■
Do not install the printer where an object may fall on 
it. The object may fall inside the printer, resulting in 
malfunction.
•
Do not place any object on top of...


6123 4 5
2
2
1 3
1
2
AB
Turn the Power On
Confirm that the POWER lamp (B) lights green.
Turn on the printer (A).
Plug the power cord into the back left of the 
printer, then connect the other end to the wall 
outlet.
Do NOT connect the USB cable at this stage.
• 


61 234 5
3
1
A
B
C
D
2
Install the Print Head
Handle the Print Head carefully. Do not drop or 
apply excessive pressure to it.
•
Open the Top Cover (C).
The Print Head Holder (D) comes out. (This is where you install the 
Print Head.)
The Print Head Holder makes a noise as it moves. This is normal operation.
•
If the Print Head Holder does not move, make sure that the printer is tu\
rned on.
•
Press the  button (A).
The Front Tray (B) opens. 


3
45
3
E
Firmly raise the Print Head Lock Lever (E) until it stops.
There may be some transparent or light blue ink on the inside of the bag\
 the Print Head comes in, 
or the inside of the protective cap - this has no effect on print quality. Be careful not to get ink on 
yourself when handling these items. Be careful not to stain your hands.
•
Remove the orange protective cap.
Remove the Print Head from the silver 
package. 


61 234 5
7
6
E
Lower the Print Head Lock Lever (E) completely.
Set the Print Head in place.
Pinch the Print Head Lock Lever firmly and lower it gently.
•
Do not knock the Print Head against the sides of the holder.
• Once you have installed the Print Head, do not remove it unnecessarily.
• 


4
2
1
1
2
A
Install the Ink Tanks
Handle the ink tanks carefully. Do not drop or 
apply excessive pressure to them.
•
Pull the orange tape (1) in the 
direction of the arrow to peel off the 
protective film and remove the film (2) 
completely.
Do not hold the sides of the ink tank; ink may splash.
•
If the Print Head Holder moves to the right, close 
and reopen the Top Cover.
•
Be sure to use the supplied ink tanks.
•
While pressing down with your left thumb, twist off the orange 
protective cap...