Canon printer PIXMA MG5622 User Manual
Have a look at the manual Canon printer PIXMA MG5622 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1335 Canon manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
8. Enter the passphrase, then click Next>. Enter the passphrase set to the access point. The passphrase should be a string of 8 to 63 alphanumeric characters or a 64-digit hexadecimal value. If you do not know the access point passphrase, refer to the instruction manual provided with the access point or contact its manufacturer. The dynamic encryption method is selected from either TKIP (basic encryption) or AES (secure encryption) automatically. Important • If Auto is not displayed on Dynamic Encryption Type: , select either TKIP(Basic Encryption) or AES(Secure Encryption) . 9. Click Finish . 261
Important • If the printer cannot communicate with the computer after the encryption type of the printer wasswitched, make sure that encryption types for the computer and the access point match that set to the printer. Note • Changing the network settings with the USB cable temporarily may switch the default printer. In this case, reset Set as Default Printer . 262
Changing the Settings in the Wired LAN Sheet Note • This screen is not available depending on the printer you are using. • Activate the wired LAN setting of the printer to change the settings in the Wired LAN sheet. 1. Start up IJ Network Tool. 2. Select the printer in Printers:. 3. Select Configuration... from the Settings menu. 4. Click the Wired LAN tab. The Wired LAN sheet is displayed. For details on the Wired LAN sheet, see Wired LAN Sheet . 5. Change the settings or confirm. Set the IP address of the printer to be used over the LAN. Specify a value appropriate for your network environment. 6. Click OK. After changing configuration, a screen is displayed asking you for confirmation before the settings are sent to the printer. If you click Yes, the settings are sent to the printer and the Transmitted Settings screen is displayed. 263
Changing the Settings in the Admin Password Sheet Note • You cannot change the settings when using the access point mode. 1. Start up IJ Network Tool. 2. Select the printer in Printers:. 3. Select Configuration... from the Settings menu. 4. Click the Admin Password tab. The Admin Password sheet is displayed. For details on the Admin Password sheet, see Admin Password Sheet . 5. Change the settings or confirm. To use an administrator password, select the Use admin password check box and enter a password. Important • The password should consist of alphanumeric characters and be no longer than 32 characters. The password is case-sensitive. Do not forget the password you set. If you forget the administrator password you specified, initialize the printer to revert the passwordto the default setting. 6. Click OK. A screen is displayed asking you for confirmation before the settings are sent to the printer. If you click Yes , the settings are sent to the printer and the Transmitted Settings screen is displayed. 264
Monitoring Wireless Network Status Note • This screen is not available depending on the printer you are using. • When using the machine over the wired LAN, you cannot monitor network status. 1. Start up IJ Network Tool. 2. Select the printer in Printers:. 3. Select Status from the View menu. The Status screen is displayed and you can check the printer status and connection performance. Important • If the indicated value is low, move your printer closer to the wireless network device. 4. If you measure the connection performance in detail, click Advanced Measurement.... The Connection Performance Measurement screen is displayed. 5. Click Next> . The measurement starts and the status displays. Measurement takes a few minutes. 265
6.Check the status. When the measurement is complete, the status is displayed. When is displayed in Connection Performance between the Printer and the Access Point: , the printer can communicate with the access point. Otherwise, refer to displayed comments and the following to improve the status of communication link, and click Remeasurement. • Check that the printer and the access point are located within the wireless connectivity range with no obstacles between them. • Check if the distance between the printer and the access point is not too far. If they are too far, move them closer together (within 164 ft./50 m). • Check that there is no barrier or obstacle between the printer and the access point. In general, connection performance decreases for communications through walls or between different floors. Adjust the locations to avoid such situations. • Check that there are no sources of radio interference near the printer and the access point. The wireless connection may use the same frequency band as microwave ovens and other sources of radio interference. Try to keep the printer and the access point away from such sources. • Check if the radio channel of the access point is close to that of other access points nearby. If the radio channel of the access point is close to that of other access points nearby, the connection performance may become unstable. Be sure to use a radio channel that does not interfere with other access points. • Check that the printer and the access point face each other. Connection performance may depend on the orientations of the wireless devices. Replace the access point and the printer in another direction to achieve the best performance. • Check whether other computers are not accessing the printer. If appears in the result of the measurement, check whether other computers are not accessing the printer. 266
If still appears even if you have tried the above, finish the measurement, then restart the IJ Network Tool to start over the measurement.7. Click Finish . Note • If any messages appear on Overall Network Performance: , move the machine and access point as instructed to improve the performance. 267
Initializing the Network Settings of the Machine Important • Note that initialization erases all network settings on the machine, printing or scanning operation from acomputer over network may become impossible. To use the machine over network, perform setup with the Setup CD-ROM or perform setup according to the instructions on our website. 1. Start up IJ Network Tool. 2. Select the printer in Printers:. 3. Select Maintenance... from the Settings menu. The Maintenance screen is displayed. 4. Click Initialize . 5. When the confirmation screen is displayed, click Yes. The network settings of the printer is initialized. Do not turn off the printer during initialization. Click OK when initialization is complete. Performing initialization when connected over wireless LAN will break the connection, so perform setup with the Setup CD-ROM or perform setup according to the instructions on our website. Note • You can change the network settings of the printer using IJ Network Tool with USB connection after initializing the LAN settings. To change the network settings using Canon IJ Network Tool, activate wireless LAN in advance. 268
Viewing the Modified SettingsThe Confirmation screen is displayed when you modified the printer settings on the Configuration screen. When you click Yes on the Confirmation screen, the following screen is displayed for confirming the modified settings.269
Screens for Network Connection of IJ Network Tool Canon IJ Network Tool Screen Configuration Screen Wireless LAN Sheet Search Screen WEP Details Screen WPA/WPA2 Details Screen Authentication Type Confirmation Screen PSK:Passphrase and Dynamic Encryption Setup Screen Setup Information Confirmation Screen Wired LAN Sheet Admin Password Sheet Network Information Screen Access Control Sheet Edit Accessible MAC Address Screen/Add Accessible MAC Address Screen Edit Accessible IP Address Screen/Add Accessible IP Address Screen 270