Canon printer PIXMA MG2924 User Manual

Default Values Set at Factory (Network)Default Values of the LAN ConnectionItemThe defaultEnable/disable LANEnableSSIDBJNPSETUPCommunication modeInfrastructureWireless LAN securityDisableIPv4 IP addressAuto setupIPv6 IP addressAuto setupSet printer name*XXXXXXXXXXXXEnable/disable IPv6EnableEnable/disable WSD (WSD settings)EnableTimeout setting (WSD settings)1 minuteEnable/disable Bonjour (Bonjour settings)EnableService name (Bonjour settings)Canon MG2900 seriesLPR protocol settingEnablePictBridge...

Connecting the Machine to the Computer Using a USB CableConnect the machine and the computer using a USB cable as the illustration below. The USB port is located
on the rear of the machine.182 

When Detecting the Printers Have the Same Name during SetupWhen the printer is detected during setup, you may see multiple printers of the same name on the detection
result screen.
Select a printer with checking the MAC address or the serial number set to the printer against that on the detection result screen.
Note
•
A serial number may not be displayed on the detection result screen.
To check the MAC address of the printer, print out the network setting information.
Printing Out Network Setting...

Connecting to Other Computer with LAN/Changing the Connection
Method from USB to LAN
To add the computer connecting the machine with LAN or to change the connection method between the
machine and the computer from USB to LAN, perform setup with the Setup CD-ROM or perform it according
to the instructions on our website.
Connecting to Other Computer with LANTo add the computer connecting the machine with LAN, perform setup with the Setup CD-ROM orperform it according to the instructions on our website....

Printing Out Network Setting InformationYou can print out the current network settings of the machine.
Important
•
This print out contains valuable information about your computer. Handle it with care.
1.
Make sure that the printer is turned on.
2.
Load a sheet of A4 or Letter-sized plain paper.
3.
Press and hold the  Stop button until the  Alarm lamp flashes 15 times.
4.
Release the  Stop button.
The machine starts printing the network setting information.
The following information on the machine's...

IPv6 Default Gateway *2Default Gateway (IPv6)XXXX:XXXX:XXXX:XXXX
XXXX:XXXX:XXXX:XXXXSubnet Prefix Length *2Subnet Prefix LengthXXXIPsec *3IPsec settingActiveSecurity Protocol *3Method of the Security ProtocolESP/ESP & AH/AHWPS PIN CODEWPS PIN codeXXXXXXXXWireless LAN DRXDiscontinuous reception
(wireless LAN)Enable/DisableOther SettingsOther settings-Printer NamePrinter namePrinter name (Up to 15 alphanumeric characters)WSDWSD settingEnable/DisableWSD TimeoutTimeout1/5/10/15/20 [min]LPR ProtocolLPR...

About Network Communication
Changing and Confirming Network Settings
Screens for Network Connection of IJ Network Tool
Other Screens of IJ Network Tool
Appendix for Network Communication
187 

Changing and Confirming Network Settings
IJ Network Tool
Changing the Settings in the Wireless LAN Sheet
Changing the WEP Detailed Settings
Changing the WPA/WPA2 Detailed Settings
Changing the Settings in the Wired LAN Sheet
Changing the Settings in the Admin Password Sheet
Monitoring Wireless Network Status
Initializing the Network Settings of the Machine
Viewing the Modified Settings
188 

IJ Network ToolIJ Network Tool is a utility that enables you to display and modify the machine network settings. It is installed
when the machine is set up.
Important
•
To use the machine over LAN, make sure you have the equipment necessary for the connection type, such as an access point or a LAN cable.
•
Do not start up IJ Network Tool while printing.
•
Do not print when IJ Network Tool is running.
•
If the firewall function of your security software is turned on, a message may appear warning thatCanon...

Changing the Settings in the Wireless LAN SheetTo change the wireless network settings of the printer, connect the printer and the computer with a USB
cable temporarily. If you modify the wireless network settings of the computer over wireless connection
without USB connection, your computer may not be able to communicate with the machine after modifying
the settings.
Note
•
This screen is not available depending on the printer you are using.
•
Activate the wireless LAN setting of the printer to change...