Canon printer PIXMA iP3600 User Manual

							Getting Started
Make sure to read this manual before using the printer. Please keep it in hand for future reference.
iP3600
=Read Me First=
Photo Printer
series 
						

							S y m b o l s
■
The following symbols are used to mark important instructions. Observe these instructions.
Additional explanations. Instructions that, if ignored, could result in personal injury or material damage.
Instructions that must be observed for safe operation.
Microsoft is a registered trademark of Microsoft Corporation.
Windows is a trademark or registered trademark of Microsoft Corporation \
in the U.S. and/or other countries.
Windows Vista is a trademark or registered trademark of Microsoft Corporation in \
the U.S. and/or other countries.
Macintosh and Mac are trademarks of Apple Inc., registered in the U.S. and other countries.
•
•
•
•
Descriptions for operations that take some time to complete.
Model Number: K10322(iP3600) 
						

							  
Contents
Check the Included ItemsTurn the Power OnInstall the Print Head Install the Ink TanksInstall the SoftwareLoading Paper12
34
5
6
After Installing the Printer 
						

							2
12 3 4 56
1
Check the Included Items
Before turning on the printer, remove all the orange tapes and the protective sheets.
•
power cord
 Print Head   ink tank 
Manuals
Setup CD-ROM (containing the drivers, applications and on-screen manuals)
Warranty
•
•
•
A USB cable is necessary to connect the printer with your computer.
• 
						

							  3
12 3 4 5 6
(1)(2)
(A)(B)
2
231
Turn the Power On
Plug in the power cord on the left side at the 
back of the printer and connect the other end 
to the wall outlet. Press the  
ON   button  (A) to turn on the printer. Confirm that the   POWER   lamp  (B) lights 
green.
Do NOT connect the USB cable at this stage.
• The printer may make some operating noises. 
This is normal operation.
• 
						

							
(B)
(A)
(C)
(D)
3
12
Install the Print Head
Open the Paper Output Tray (A) and the Top 
Cover (B).Raise the Print Head Lock Lever (D).
Firmly raise the Print Head Lock Lever until it stops. (The Print 
Head Lock Lever may feel heavy.)
•
If the Print Head Holder does not move, make sure that the 
printer is turned on.
•
The Print Head Holder (C) comes out. (This is where 
you install the Print Head.)
Do not handle the Print Head 
roughly such as applying them 
excessive pressure or dropping 
them.
•
The Print Head Holder makes a noise as it moves. 
This is normal operation.
• 
						

							  5
1 234 5 6
(D)
453
Remove the  Print Head  from 
the silver package.Remove and discard the orange 
protective cap.
Tilt the  Print Head  and set it in place. Lower the  Print Head Lock Lever  
(D) completely.
There may be some transparent or light blue ink on the inside of the bag\
 the  Print 
Head  comes in, or the inside of the protective cap - this has no effect on print 
quality. Be careful not to get ink on yourself when handling these items. Be ca\
reful 
not to stain your hands.
•
Do not to knock the  Print Head  against the sides of the Holder.
Pinch the  Print Head Lock Lever  fi rmly and lower it gently.
Once you have installed the  Print Head , do not remove it unnecessarily.
•
•
• 
						

							
(1)
(2)
(A)
4
12
Install the Ink Tanks
Pull the orange tape (1) in the 
direction of the arrow to peel off the 
protective film and remove the film (2) 
completely.
Do not hold the sides of the ink tank; ink may splash.
•
Do not handle the ink tanks roughly such as 
applying them excessive pressure or dropping 
them.
•
While pressing down with your left thumb, twist off the 
orange protective cap (A) located on the bottom of the 
ink tank.
If the Print Head Holder moves to the right, 
close and reopen the Top Cover.
Be sure to use the supplied ink tanks.
•
• 
						

							  7
5 6
1 2 34
43
Install all the other  ink tanks  in the same way.
Install all the  ink tanks .
Make sure all the   Ink   lamp  lights red.
• Once you have installed the  ink tanks , do not remove them unnecessarily.
•
Press the   PUSH  mark on the  ink tank  until it clicks into 
place.
Make sure the   Ink   lamp  lights red.
I n s t a l l   t h e    I n k   Ta n k  
Match the labels when installing.
• 
						

							8
5 6
1 2 34
(B)
(C)
56
4
Wait until the   POWER   lamp  lights green (about 4 minutes) and go to the 
next step.
The printer may make some operating noises when preparing to print. 
This is normal operation.
•
•
Close the  Top Cover .
If an  
Alarm    lamp  (B) fl ashes orange, make sure that the  Print Head  and the  ink 
tanks  are correctly installed.
•
Load three or more sheets of  A4  or  Letter -sized plain paper into the 
 Cassette  (C).
For details, refer to " 6 Loading Paper " on page 22.
Close the  Paper Output Tray  to make it easier to pull out the  Cassette .
•
•
Install the  Ink Tanks