Canon Pixma Mx492 User Guide

Summary of Reports and Lists•
TX report
Selects whether to print TX REPORT/ERROR TX REPORT automatically after sending a fax.
If you print the report, select  Print error only or Print for each TX .
If you select  Print error only  or Print for each TX , you can specify the print setting that the first page
of the fax is printed along with the report.
•
RX report
Selects whether to print RX REPORT automatically after receiving a fax.
If you print RX REPORT, select  Print error only or Print for each RX...

Output settings•
Prevent abrasion
Use this setting only if the print surface becomes smudged.
Important
•
Be sure to set this back to  OFF after printing since it may result in lower printing speed or lower
print quality.
•
Extended copy amt.
Selects the amount of image that extends off the paper when copying in Borderless (full). Slight cropping may occur at the edges since the copied image is enlarged to fill the whole page. You
can change the width to be cropped from the borders of the original image...

LAN settings•
Change LAN
Enables/disables either wireless LAN or access point mode.
•
Wireless LAN setup
If your wireless router is compatible with WPS, set up wireless LAN following the on-screen instructions.
If not, select one of the setup methods below.
◦
Standard setup
Select when you perform settings for wireless LAN manually using the operation panel of the machine.
◦
WPS (Push button)
Select when you perform settings for wireless LAN using a wireless router supporting a Wi-Fi Protected Setup...

Note•
You cannot use the same printer name as that already used for other LAN connected devices.
•
You cannot use a hyphen for the initial or last character of the printer name.
◦
TCP/IP settings
Performs IPv4 or IPv6 setting.
◦
WSD setting
Setting items when you use WSD (one of the network protocols supported in Windows 8.1,
Windows 8, Windows 7, and Windows Vista).
Enable/disable WSD Selects whether WSD is enabled or disabled.
Note
•
When this setting is enabled, the printer icon is displayed on the...

Dev. user settings•
Date/time setting
Sets the current date and time.
Setting the Sender Information
Important
•
If a power failure occurs or you unplug the power cord, the date/time settings will be reset.
•
Date display format
Sets the format of dates displayed on the LCD and printed on sent faxes.
•
DST setting
Some countries adopt the daylight saving time (summer time) system that shifts the clock time forward
at certain periods of the year.
You can set your machine to automatically change the time...

Romanian / Bulgarian / Turkish / Greek / Estonian / Latvian / Lithuanian / Simplified Chinese / Traditional
Chinese / Korean / Indonesian / Vietnamese•
Key repeat
Enables/Disables continuous input by pressing and holding down the 
 button when setting the
number of copies, the zoom ratio, etc.
•
Device info sending
Selects whether you will send the printer usage information to Canon server. The information sent to
Canon will be utilized to develop better products. Select  ON to send the printer usage...

Firmware updateYou can update the firmware of the machine, check the firmware version, or perform settings of a
notification screen, a DNS server and a proxy server.
Note
•
Only  Current version  is available when  LAN inactive is selected for  Change LAN in LAN settings .
•
Install update
Performs the firmware update of the machine.
•
Current version
You can check the current firmware version.
•
Update notification
When  ON is selected and the firmware update is available, the screen to inform you of...

Cassette settingsBy registering the paper size and the media type loaded in the cassette, you can prevent the machine frommisprinting by displaying the message before printing starts when the paper size or the media type of the
loaded paper differs from the print settings.
For details:
Paper setting for Printing
•
Register paper info
Registers the paper size and the media type you load in the cassette.
Note
•
For details on the combination of paper settings you can specify by the printer driver or on the...

Reset settingReturns all settings you made to the machine back to the default. However, some data may not be changed,
depending on the current usage state of your machine.
Important
•
Depending on the setting item, it is necessary to perform connection or setup again after you have
returned the setting back to the default.
•
Web service setup
Returns the Web service settings back to the default.
•
LAN settings
Returns the LAN settings other than the administrator password specified by IJ Network Tool...

About Quiet settingEnables this function on the machine if you want to reduce the operating noise, such as when printing at
night. In addition, you can specify the time range to reduce the operating noise.
Important
•
Set the current date and time in advance.
Setting the Sender Information
Follow the procedure below to perform setting.
1.
Make sure that the machine is turned on.
2.
Press the  Setup button.
The  Setup menu  screen is displayed.
3.
Use the  button to select  Quiet setting, then press the...