Canon Pixma Mx330 Quick Start Guide

							Make sure to read this manual before using the machine. Please keep it i\
n hand for future reference.
Getting Started
=Read Me First=
series
Office All-In-One
 
						

							S y m b o l s
■
The following symbols are used to mark important instructions. Observe 
these instructions.
Model Number: K10332 (MX330)
Macintosh and Mac are trademarks of Apple Inc., registered in the U.S. and other 
countries.
• Microsoft is a registered trademark of Microsoft Corporation.
•
Windows is a trademark or registered trademark of Microsoft Corporation in the U.S. 
and/or other countries.
•
Windows Vista is a trademark or registered trademark of Microsoft Corporation in \
the 
U.S. and/or other countries.
•
8
After Installing the Machine Install the Software
7
Install the FINE Cartridges5
Turn the Power On4
Remove the Protective Material2
Loading Paper Connect the Telephone Line
3
Set Up for Fax Reception6
Preparation1
Contents
Additional explanations.
Instructions that, if ignored, could result in personal injury or 
material damage.
Instructions that must be observed for safe operation.
Descriptions for operations that take some time to complete.
Caution
 
						

							
1234567812345678
1
Preparation
Before turning on the machine, remove all the orange tapes and the protective sheets.power cord
FINE cartridges
Color Black
A USB cable is necessary to connect the machine with your computer.
•
Manuals•
Setup CD-ROM (containing the drivers, applications and on-screen manuals)
•
Warranty
•
C h e c k   t h e   I n c l u d e d   I t e m s
■
Choosing a Location
□
Do not install the machine where an object may fall on it. The 
object may fall into the Rear Tray, resulting in malfunction.
•
Do not place any object on the Document Cover. It may 
fall into the Rear Tray when opening the Document Cover, 
resulting in malfunction.
•
telephone line cable
 
						

							
12345678
2
C
EB
D
B
A
C
1234
Remove the Protective Material
Open the Paper Output 
Tray (A).Lift the Scanning Unit (Cover) (B) until it 
locks into place. Then, lift the Scanning Unit (Cover) (B) slightly 
and fold the Scanning Unit Support (C), then 
gently close the Scanning Unit (Cover) (B).
Pull the orange protective tape 
(D) and remove the protective 
material (E).
The Scanning Unit Support (C) is fixed 
automatically.
 
						

							
12345678
B
A
12
3
Connect the Telephone Line
This section describes the basic method of 
telephone line connection.Connect the machine with a telephone line using the 
supplied telephone line cable (A).
Do not connect the machine and a telephone in parallel 
to the same telephone line using a distribution adapter. 
The machine may not operate properly.
•
Remove the telephone connector cap (B), then 
connect a telephone with the telephone line 
cable.
To use the machine as a fax, a telephone 
line needs to be connected.
If you cannot send faxes after installing the 
machine, check the telephone line type. For 
details, refer to "Confirming the Telephone Line 
Connection" in the on-screen manual: 
Basic 
Guide .
•
For other connection methods, refer to the on-
screen manual: 
Basic Guide.
When using as a fax only:Go to "4 Turn the Power On" on page 4.
When not using 
as a fax:
When using as 
both a fax and 
telephone:
When using as 
a fax only: Go to "4 Turn 
the Power On" 
 
on page 4.
 only
Only when connecting a telephone:
 
 
						

							
4
2
1
12
12345678
C
D
B
A
34
Turn the Power On
Plug the power cord into the left side of 
the machine, then connect the other end 
to the wall outlet. Turn on the machine (A).
Do NOT connect the USB cable at this stage.
• Make sure that the Document 
Cover (B) is closed.
•
Use the 
{ or 
} button (C) on the Operation 
Panel to select the language for the LCD, then 
press the OK button.
If an unintended language is displayed on the LCD, press the  Back button (D) to return to the 
Language selection  screen.
•
The standby screen is 
displayed.
 
						

							
12345678
EAD
F
1
5
Install the FINE Cartridges
Be sure to use the supplied FINE Cartridges.
•
Lift the Scanning Unit (Cover) (A) until it locks into place.
Handle the FINE Cartridges carefully. Do not 
drop or apply excessive pressure to them.
•
The Scanning Unit Support (E) is fixed automatically.
If the FINE Cartridge Holder returns to the right, close the Scanning Unit (Cover) and reopen it.
•
The FINE Cartridge Holder (F) comes out. (This is where you install the cartridges.)
If the FINE Cartridge Holder does not come out, make sure that the machine is turned on.
•
Close the Document Cover (D) and lift it with the Scanning Unit (Cover).
 
						

							
5
H
32
G
4
Open the Ink Cartridge Locking Cover  on the right side.
Pinch (G) firmly and pull up the cover.
Remove the Black FINE Cartridge 
 from its box.
Be careful not to stain your hands or surrounding work area with ink on \
the removed protective tape.
•
Pull the orange protective tape (H) in the direction of 
the arrow and remove it gently.
 
						

							
12345678
65
Push down  of the Ink Cartridge Locking Cover until you hear a click to 
close it completely.
View the Ink Cartridge Cover  straight on and check that it is locked correctly (not 
at an angle).
Insert the Color FINE Cartridge 
 into the left FINE Cartridge Holder  in the same 
way.
Place the Black FINE Cartridge  into the right slot .
Do not knock the FINE Cartridge against the sides of the holder.
•
Install the Black FINE Cartridge into the right slot, and the Color FINE Cartridge into the left 
slot.
•
Install in a well-lit environment.
•
 
						

							
5
E
A
12345678
7
Wait until the standby screen appears on the LCD (about 1-2 minutes) and go to the next step.
•
Once you have installed the FINE Cartridges, do not remove them unnecessarily .
•
Lift the Scanning Unit (Cover) (A) slightly and fold the Scanning Unit Support (E), then gently close the Scanning Unit (Cover) (A).
If an error message is displayed on the LCD, make sure that the FINE Cartridges are correctly installed.
•