Canon Pixma Mg2924 User Guide

Disabling the Wireless LAN Function of the MachineFollow the procedure below to disable the wireless LAN.1.
Make sure that the machine is turned on.
2.
Press and hold the  Stop button until the  Alarm lamp flashes 18 times.
3.
Release the  Stop button.
4.
Press the  Black button.
The  Wi-Fi  lamp goes off.
Note
•
When you enable the wireless LAN, press the  Color button in step 4.
181
 

Information about Network Connection
Useful Information about Network Connection
182
 

Useful Information about Network Connection
Default Values Set at Factory (Network)
Connecting the Machine to the Computer Using a USB Cable
When Detecting the Printers Have the Same Name during Setup
Connecting to Other Computer with LAN/Changing the Connection Method
from USB to LAN
Printing Out Network Setting Information
183
 

Default Values Set at Factory (Network)Default Values of the LAN ConnectionItemThe defaultEnable/disable LANEnableSSIDBJNPSETUPCommunication modeInfrastructureWireless LAN securityDisableIPv4 IP addressAuto setupIPv6 IP addressAuto setupSet printer name*XXXXXXXXXXXXEnable/disable IPv6EnableEnable/disable WSD (WSD settings)EnableTimeout setting (WSD settings)1 minuteEnable/disable Bonjour (Bonjour settings)EnableService name (Bonjour settings)Canon MG2900 seriesLPR protocol settingEnablePictBridge...

Connecting the Machine to the Computer Using a USB CableConnect the machine and the computer using a USB cable as the illustration below. The USB port is located
on the rear of the machine.185
 

When Detecting the Printers Have the Same Name during SetupWhen the printer is detected during setup, you may see multiple printers of the same name on the detection
result screen.
Select a printer with checking the MAC address or the serial number set to the printer against that on the detection result screen.
Note
•
A serial number may not be displayed on the detection result screen.
To check the MAC address of the printer, print out the network setting information.
Printing Out Network Setting...

Connecting to Other Computer with LAN/Changing the Connection
Method from USB to LAN
To add the computer connecting the machine with LAN or to change the connection method between the
machine and the computer from USB to LAN, perform setup with the Setup CD-ROM or perform it according
to the instructions on our website.
Connecting to Other Computer with LANTo add the computer connecting the machine with LAN, perform setup with the Setup CD-ROM orperform it according to the instructions on our website....

Printing Out Network Setting InformationYou can print out the current network settings of the machine.
Important
•
This print out contains valuable information about your computer. Handle it with care.
1.
Make sure that the printer is turned on.
2.
Load a sheet of A4 or Letter-sized plain paper.
3.
Press and hold the  Stop button until the  Alarm lamp flashes 15 times.
4.
Release the  Stop button.
The machine starts printing the network setting information.
The following information on the machine's...

IPv6 Default Gateway *2Default Gateway (IPv6)XXXX:XXXX:XXXX:XXXX
XXXX:XXXX:XXXX:XXXXSubnet Prefix Length *2Subnet Prefix LengthXXXIPsec *3IPsec settingActiveSecurity Protocol *3Method of the Security ProtocolESP/ESP & AH/AHWPS PIN CODEWPS PIN codeXXXXXXXXWireless LAN DRXDiscontinuous reception
(wireless LAN)Enable/DisableOther SettingsOther settings-Printer NamePrinter namePrinter name (Up to 15 alphanumeric characters)WSDWSD settingEnable/DisableWSD TimeoutTimeout1/5/10/15/20 [min]LPR ProtocolLPR...

About Network Communication
Changing and Confirming Network Settings
Screens for Network Connection of IJ Network Tool
Other Screens of IJ Network Tool
Appendix for Network Communication
190