Canon Pixma Ip90v Quick Start Guide

Printing Maintenance
57
Aligning the Print Head
If ruled lines are displaced or the print result is unsatisfactory, Print Head alignment is 
required.
ì
1With the printer on, load a sheet of Letter-sized plain paper in the printer.
Move the Paper Thickness Lever (gray) to the right position.
2Open the Printer Properties dialog box.
See Opening the Printer Properties Dialog Box Directly from the Start Menu
Opening the Printer Properties Dialog Box Directly from the Start MenuOpening the Printer Properties...

Printing Maintenance
58
4 Align the Print Head.
(1)Look at the print out. From the patterns, select the most even, least irregular 
patterns.
(4)When the confirmation message is displayed, click OK
OKOK OK. NoteIf it is difficult to pick up the best pattern on Column H, pick the setting 
that produces the least noticeable vertical white stripes.
(4)After the pattern is printed, click Yes
YesYes Yes.
(2)Enter the numbers.
(3)Click OK
OKOK OK.
Less noticeable white stripes More noticeable white stripes...

Printing Maintenance
59
1With the printer on, load a sheet of Letter-sized plain paper in the printer.
Move the Paper Thickness Lever (gray) to the right position.
2Open the BJ Printer Utility dialog box.
(1)Double-click the hard disk icon where the printer driver was installed, the 
Applications
ApplicationsApplications Applications folder, and the Utilities
UtilitiesUtilities Utilities folder.
(2)Double-click the Printer Setup Utility
Printer Setup UtilityPrinter Setup Utility Printer Setup Utility...

Printing Maintenance
60
4Align the Print Head.
(1)Look at the print out. From the patterns, select the most even, least irregular 
patterns.
NoteIf it is difficult to pick up the best pattern on Column H, pick the 
setting that produces the least noticeable vertical white stripes.
(2)Enter the numbers.
(3)Click Send
SendSend Send.
Less noticeable white stripes More noticeable white stripes
iP90_QSG_US.book  Page 60  Thursday, December 7, 2006  11:03 AM
 

Printing Maintenance
61
Replacing an Ink Tank
If the print result is not improved after maintenance such as Print Head 
cleaning, an ink tank runs out of ink. Replace the ink tank with a new one. 
When replacing an ink tank, check the model number very carefully. 
The printer will not print properly if the wrong ink tank is used, or installed in 
the incorrect position.

Replacing an Ink Tank
When an ink tank runs out of ink, replace it using the following steps.
1Ensure that the printer is turned on,...

Printing Maintenance
62
2Remove the empty ink tank.
(1)Push the tab.
(2)Remove the ink tank.
Then lift it from its slot.
Do not touch the Lock lever; remove only the ink tank.
3Prepare a replacement ink tank.
(1)Unpack a new ink tank and remove the orange Protective Cap. Important• Handle ink tanks carefully to avoid staining your clothes or 
surrounding area.
• Discard empty ink tanks according to the local laws and regulations 
regarding disposal of consumables.
Important• Do not re-attach the...

Printing Maintenance
63
4Insert the ink tank.
(1)Insert a new ink tank with it slightly slanted.
(2)Push down on the   on the ink tank until it clicks into place.
5Close the Print Head Cover.
The Print Head Holder moves to the right.
ImportantWhen an ink tank is replaced, the ink counter must be reset.
See Resetting the Ink Counter
Resetting the Ink CounterResetting the Ink Counter Resetting the Ink Counter on page 64
Note• To maintain optimal print quality, use an ink tank within six months 
of its...

Printing Maintenance
64

Resetting the Ink Counter
When an ink tank is replaced, the ink counter must be reset.
The low ink warning is only displayed properly if the ink counter is reset.
Message Prompting Confirmation of Ink Tank Replacement
If an ink tank is removed, the printer will send a message prompting you to confirm 
replacement of the ink tank at the start of the next print job.
When an ink tank has been replaced, follow the procedure below to reset the ink 
counter. The low ink warning is only...

Printing Maintenance
65
Resetting the Ink Counter in the Printer Properties dialog box
1Open the Printer Properties
Printer PropertiesPrinter Properties Printer Properties dialog box and click the Maintenance
MaintenanceMaintenance Maintenance tab.
See Opening the Printer Properties Dialog Box Directly from the Start Menu
Opening the Printer Properties Dialog Box Directly from the Start MenuOpening the Printer Properties Dialog Box Directly from the Start Menu Opening the Printer Properties Dialog Box...

Printing Maintenance
66
2Reset the Ink Counter.
(2)  Click Ink Counter Reset
Ink Counter ResetInk Counter Reset Ink Counter Reset. (1)  Select Remaining ink level setting
Remaining ink level settingRemaining ink level setting Remaining ink level setting 
from the pop-up menu.
(4) Click OK
OKOK OK. (3)  Select the newly installed ink tank.
iP90_QSG_US.book  Page 66  Thursday, December 7, 2006  11:03 AM