Canon network camera VBS905F User Manual

							[Video] Setting Video Size, Quality and Frame Rate
51
Setting Page
3
(2) [Bit Rate Control] 
Select [Do not use bit rate control] or [Use bit rate 
control].
Select [Use bit rate control] when [Video Format] 
under [Upload] is set to [H.264(1)] or when [Video 
Format] under [Memory Card] is set to [H.264(1)].
(3) [Target Bit Rate (kbps)] 
If [Use bit rate control] is selected in (2), select a 
desired target bit rate from the 17 levels from [64] to 
[16384].
(4) [Video Quality] 
If [Do not use bit rate control] is selected in (2), select 
a desired quality from 1 to 5 (total 5 levels) for H.264 
video transmission. 
Greater values have higher quality. 
(5) [Frame Rate (fps)] 
Select [30], [15], [10], [6], [5], [3], [2] or [1] (fps) for 
the frame rate of video transmitted.
(6) [I Frame Interval (sec)]
Select [0.5], [1], [1.5], [2], [3], [4] or [5] for the I frame 
interval (sec) for H.264 video.
H.264(2)
(1) [H.264(2)]
Select [Enable] to distribute H.264 video using two 
streams.
H.264(2) video can be displayed using Admin Viewer 
and RM-Lite Viewer. It cannot be used for upload, 
memory card recording, or by VB Viewer.
Refer to the settings for “H.264(1)” for details about 
[Video Size], [Bit Rate Control], [Target Bit Rate (kbps)], [Video Quality], [Frame Rate (fps)], and [I 
Frame Interval (sec)] settings.
On-screen display
(1) [Date display] 
Select whether to enable date display over video. If 
[Enable] is selected, date information will be 
displayed over video. 
(2) [Position of date display] 
Select [Upper left], [Upper right], [Lower left] or 
[Lower right] for the position of date display 
information. 
(3) [Format of date display] 
Select [YYYY/MM/DD], [DD/MM/YYYY] or [MM/DD/
YYYY] for the format of the date display. 
Important
When streaming two H.264 videos, setting the video size 
settings for H.264(1) and H.264(2) to the following 
combinations restricts the frame rate to a maximum of 15 fps.
For all other combinations, a frame rate of up to 30 fps can be 
selected.
H.264(1)H.264(2)
1920 x 1080 All sizes
All sizes 1920 x 1080
1280 x 960 1280 x 960
1280 x 720 1280 
X 720
Important
 When [H.264(1)] is selected for the memory card recording 
and upload settings, the following restrictions apply to the 
[H.264(1)] setting.
- Only [Use bit rate control] can be selected for [Bit Rate 
Control].
- Only [3072] or less can be selected for [Target Bit Rate 
(kbps)].
- Only one of [0.5], [1], and [1.5] can be selected for [I 
Frame Interval (sec)].
 Network load will increase if a larger video size is set or 
higher video quality and target bit rate are set, as this 
increases data size per frame. As a result, the following could 
occur:
JPEG: The frame rate may drop
H.264: Video may be temporarily disrupted
 Block noise may become noticeable if a large video size and 
low target bit rate are set. 
 The data size may increase depending on the type or 
movement of the subject. If the frame rate remains low or 
other undesirable conditions continue for a prolonged 
period, lower the video size or quality setting.
 The included RM-Lite cannot record H.264 video.
 H.264 video can be displayed using Admin Viewer and RM-
Lite Viewer. H.264 video cannot be displayed using VB 
Viewer. 
						

							52
(4) [Time display] 
Select whether to enable time display over video. If 
[Enable] is selected, display time information will be 
displayed over video. 
(5) [Position of time display] 
Select [Upper left], [Upper right], [Lower left] or 
[Lower right] for the position of time display 
information. 
(6) [Text display] 
Select [Display nothing], [Display designated string] 
or [Display camera name] for the text string to display 
over video. 
If [Display designated string] is selected, the [Text 
string display] set in (8) will be displayed. 
If [Display camera name] is selected, the text string 
set in [Camera Name (alphanumeric characters)] 
under [Camera] will be shown (p. 46). 
(7) [Position of text display] 
Select the position of text display from [Upper left], 
[Upper right], [Lower left] or [Lower right]. 
(8) [Text string display] 
If [Display designated string] is selected in (6) [Text 
display], you can enter a text string of up to 15 ASCII 
characters (spaces and printable characters) for 
superimposed display on the video. 
(9) [Color of text] 
Select [Black], [Blue], [Cyan], [Green], [Yellow], 
[Red], [Magenta] or [White] for the color of text to be 
displayed over the video. 
(10)[Background color] 
Select [Black], [Blue], [Cyan], [Green], [Yellow], 
[Red], [Magenta] or [White] for the background color. 
(11)[Color depth of text and background] 
Select [Fill text and background color], [Make text 
transparent], [Make background transparent], [Make 
text semi-transparent] or [Make text and background 
semi-transparent] for the color depth of text and  
background to be displayed over the video. 
Note
 Depending on video quality settings, on-screen display may 
become difficult to decipher. Set after confirming appearance 
on actual video. 
 The on-screen display is not shown for cropped 
images using digital PTZ with horizontal size of 384 pixels or 
lower.
Important
The on-screen time display is not suitable for usage where high 
reliability is required. Use as reference information only where 
utmost and constant reliability is required for surveillance.  
						

							53
3
Setting Page
RTP Server
(1) [RTP]
Set RTP to [Disable] or [Enable].
(2) [RTSP Authentication Method]
Set the RTSP authentication method to [Basic 
Authentication], [Digest Authentication], or [No 
Authentication].
(3) [RTSP Port]
Set the RTSP port number to 554 or in the range of 
1024 to 65535.
Normally [554] (factory default setting) is used.
Audio Multicast
(1) [Multicast Address]
Set the multicast address for audio transmission in the 
range 224.0.0.0 to 239.255.255.255 (IPv4) or an 
address beginning with ff00::/8 (IPv6).
To disable Multicast, set to [0.0.0.0] (IPv4) or [::0(::)] 
(IPv6).
(2) [Multicast Port]
Set the multicast port number for audio transmission 
to an even number in the range 1024 to 65534.
To disable Multicast, set to [0].
(3) [Multicast TTL]
Set the effective scope of multicast distribution 
between 0 and 255.
To disable Multicast, set to [0].
The TTL (Time To Live), representing the effective 
scope of multicast distribution, is decremented each 
time the signal passes through a router. When the value reaches 0, the signal can no longer be 
distributed. For example, if TTL is set to [1], multicast 
distribution is confined to the local segment only and 
cannot be distributed by the router.
RTP Streaming 1 to 5
You can make settings for each stream, RTP Streaming 1 
to RTP Streaming 5, in a 5-session RTP stream 
distribution.
(1) [Video Size]
Select the video format (JPEG or H.264) and video 
size of the RTP stream.
The video sizes for JPEG will vary depending on the 
[Video Size Set] configured in [Video] > [All Videos] 
(p. 50). The video sizes for H.264 will be determined 
according to the [H.264(1)] and [H.264(2)] settings 
configured in [Video].
In addition, [H.264(1)] and [H.264(2)] cannot be set 
for multiple RTP streams.
(2) [Frame Rate]
Set the frame rate if the RTP stream is JPEG video.
For H.264, the frame rate is determined by the [Video] 
> [H.264(1)] or [H.264(2)] > [Frame Rate] setting 
(p. 51).
(3) [Multicast Address]
Set the multicast address for RTP streaming in the 
range 224.0.0.0 to 239.255.255.255 (IPv4) or an 
address beginning with ff00::/8 (IPv6).
To disable Multicast, set to [0.0.0.0] (IPv4) or [::0(::)] 
(IPv6).
(4) [Multicast Port]
Set the multicast port number for RTP streaming to an 
even number in the range 1024 to 65534.
To disable Multicast, set to [0].
(5) [Multicast TTL]
Set the effective scope of multicast distribution for 
RTP streaming between 0 and 255.
To disable Multicast, set to [0].
The TTL (Time To Live), representing the effective 
scope of multicast distribution, is decremented each 
time the signal passes through a router. When the 
value reaches 0, the signal can no longer be 
distributed. For example, if TTL is set to [1], multicast 
[RTP] 
RTP Server, Audio Multicast and RTP Streaming
The following can be set here.
Server
Enable RTP, and set the RTSP authentication 
method and port number.
 Audio Multicast
Make settings for multicast audio transmission.
Streaming 1 to 5
Make settings for RTP streaming of video, 
multicasting, and audio transmission. 
						

							54
distribution is confined to the local segment only and 
cannot be distributed by the router.
(6) [Audio Transmission]
Set RTP streaming audio transmission to [Disable] or 
[Enable].
Note
 RTP stream URL
rtsp://IP_address:port_number/rtpstream/config1(~5)=r|u|m
[=r|u|m] is optional and can be omitted. If specified, specify 
only one option.
r: Requests RTP over TCP
u: Requests RTP over UDP
m: Requests multicast
Example: RTP streaming 1 request using RTP over TCP
rtsp://192.168.100.1:554/rtpstream/config1=r
Note that the actual operation is dependent on the RTP client 
application, so the URL does not necessarily specify the 
method used for transmission.
 For H.264, the bit rate control and video quality are determined 
by the settings in [Video] (p. 51).
 Regardless of the [Server] > [Audio Server] > [Audio 
Transmission from the Camera] setting, RTP streaming audio 
will be used.
However, to use audio settings, select [Enable] for [Audio 
Transmission from the Camera] and make the settings.
 The [Access Control] > [User Authority] > [Video Distribution] 
and [Audio Distribution] settings are not used for RTP.
 RTP streaming video may not be viewable on systems using a 
proxy server or firewall. If the video cannot be viewed, contact 
the system administrator.
 If host access restrictions are applied to a client while it is 
streaming using RTP over UDP, it may take from a few to 
several seconds until streaming ceases. 
						

							55
3
Setting Page
General Upload
(1) [Upload] 
Select [Upload Disabled], [HTTP Upload] or [FTP 
Upload] for the upload method.
(2) [Video Format]
Select the [JPEG] or [H.264(1)] format for video you 
want to upload. 
If [H.264(1)] is selected, video is uploaded with the 
settings defined under [Video] > [H.264(1)] (p. 50).
 [H.264(2)] cannot be used.
(3) [Frame Rate] 
Enter the maximum frame rate of video to be 
uploaded. This setting can only be made when 
[JPEG] is selected for [Video Format].
(4) [Pre-event Buffer (number of frames)] / [Pre-event 
Buffer (sec)]
Enter the number of frames or seconds of video to be 
buffered before the event. The maximum amount is 
number of frames for a [JPEG] selection and number 
of seconds for an [H.264(1)] selection in [Video 
Format].
(5) [Post-event Buffer (number of frames)] / [Post-event 
Buffer (sec)]
Enter the number of frames or seconds of video to be 
buffered after the event. The maximum amount is 
number of frames for a [JPEG] selection and number of seconds for an [H.264(1)] selection in [Video 
Format].
Note
The server or network load may increase and the frame rate may 
drop, depending on the settings. If this occurs, try the following 
measures. Also check the settings including the network to the 
server. 
 Reduce the video file size:
– Set a lower value under [Video Quality] for [JPEG]/
[H.264(1)] (p. 50). 
– Set a lower value for [Video Size: Upload / Memory card] for 
[JPEG] (p. 50).
– Set a lower value for [Video Size] for [H.264(1)] (p. 50).
– Set a lower value under [Target Bit Rate (kbps)] for 
[H.264(1)] (p. 51).
 Reduce the uploading frequency: 
– Reduce the value in [Pre-event Buffer] or [Post-event Buffer] 
(p. 55). 
– If [Volume Detection Event] is enabled, disabled [ON Event 
Operation], [OFF Event Operation], or [Ongoing ON Event 
Operation] (p. 60). 
[Upload] 
Setting HTTP/FTP Upload and E-mail Notification
The following can be set here. 
 General Upload
Set the upload operation to be performed and the 
video buffer.
 HTTP Upload
Set HTTP connection uploads. 
 FTP Upload
Set FTP connection uploads. 
 E-mail Notification
Set event information and video e-mail 
notifications. 
Important
 If the upload function is used, either the [Event] menu must 
be set (p. 60) or the [Event] tab in the Intelligent Function 
Setting Tool (p. 110) must be set. 
 If you are using both e-mail notification by text and video and 
video upload by HTTP/FTP, set [Video Size: Upload / Memory 
card] (p. 50) to a small size.
 HTTP upload does not support SSL/TLS. 
 If the camera is set to perform upload or e-mail notification 
continuously, not all video or e-mails may be sent depending 
on the video size and the network condition to the server. In 
this case, an event log message is displayed (p. 77). 
 If the destination for HTTP/FTP upload or e-mail notification is 
set for a Windows operating system, IPsec communication 
cannot be applied.
 When an H.264 video is uploaded, the following restrictions 
apply to [H.264(1)] of [Video] (p. 50).
- Only [Use bit rate control] can be selected for [Bit Rate 
Control].
- Only [3072] or less can be selected for [Target Bit Rate 
(kbps)].
- Only one of [0.5], [1], and [1.5] can be selected for [I 
Frame Interval (sec)].
 The maximum video buffer size capacity is approx. 5 MB. 
If a large video size is set, the Frame Rate, Pre-event Buffer 
and Post-event Buffer may not be achieved as specified. 
 If buffering cannot be achieved as specified, a message is 
written to the event log (p. 77). 
Before using a large video size, confirm that no messages 
appear in the event log. 
						

							56
– From the Intelligent Function Setting Tool [Event] tab > 
disable [ON Event Operation], [OFF Event Operation] or 
[Detected mode Operation] (p. 110). 
– If [External Device Input Event] is enabled, disable [Active 
Event Operation], [Inactive Event Operation], or [Ongoing 
Active Event Operation] (p. 61). 
– If [Timer Event] is enabled, increase the value in [Repeat 
Interval] (p. 62). 
HTTP Upload
The HTTP upload function sends notifications via HTTP or 
via HTTP with attached videos, depending on the network 
camera event.
(1) [Notification] 
Select [Notification Only with HTTP] or [Video 
attached Notification with HTTP] as the content of 
notification. 
(2) [URI] 
Enter the URI to be uploaded to (using up to 255 
characters). 
(3) [User Name], [Password] 
Enter the user name and password required for 
authentication. 
Digest authentication is not supported.
(4) [Proxy Server] 
Enter the host name or IP address of the proxy server 
(using up to 63 characters). 
(5) [Proxy Port] 
Enter the port number of the proxy server (factory 
default setting is [80]). 
(6) [Proxy User Name], [Proxy Password] 
Enter the user name and password of the proxy 
server. 
Digest authentication is not supported.
(7) [Parameter (query string)] 
Enter the parameter (using up to 127 characters). 
Parameters can be specified using the “%” character 
(p. 152).
(8) [HTTP Upload Test] 
Clicking [Exec] initiates an upload test based on the 
settings currently entered. Only one JPEG image is 
uploaded. It is not necessary to click [Apply].
After entering a password, first click [Exec], then 
[Apply] the password.FTP Upload
(1) [Notification] 
The content of notification is set to [Video data upload 
with FTP]. 
(2) [FTP Server] 
Enter the host name or IP address of the FTP server 
(using up to 63 characters). 
(3) [User Name], [Password] 
Enter the user name and password required for 
authentication. 
(4) [PASV Mode] 
Select [Disable] or [Enable] for the PASV mode when 
uploading via FTP. 
(5) [File Upload Path] 
Enter the path to the folder where the video file is to be 
uploaded to (using up to 255 characters). 
(6) [File Naming] 
Set a desired file naming rule. 
[YYYYMMDDHHMMSSms] 
Video is uploaded according to the file name format 
of 
“{year}{month}{day}{hour}{minute}{second}{ms}.jpg”. 
(Example: 20150123112122000.jpg) 
[YYYYMMDD Directory/HHMMSSms] 
A subdirectory named “{year}{month}{day}” is 
created first, and then the video is uploaded using 
the file name “{hour}{minute}{second}{ms}.jpg”. 
(Example:  20150123/112122000.jpg) 
[Loop] 
Video is loaded with a file name numbered up to the 
value set in [Maximum Number of Loops]. 
(Example:  0000.jpg, 0001.jpg) 
The number will return to 0000 when the maximum 
number of loops is reached.
[Maximum Number of Loops] 
If [Loop] is set under [File Naming], enter the 
maximum number of loops in the range of 0 to 9999. 
Important
 Enter [Proxy Server], [Proxy Port], [Proxy User Name] and 
[Proxy Password] if connecting via a proxy.
 For information about the HTTP upload function and settings, 
contact your nearest Canon Customer Service Center. 
						

							[Upload] Setting HTTP/FTP Upload and E-mail Notification
57
Setting Page
3
[User Setting] 
Video is uploaded according to the file naming 
method specified in [Subdirectory Name to Create] 
and [File Name to Create]. 
[Subdirectory Name to Create], [File Name to 
Create] 
If file naming is set to [User Setting], enter the 
subdirectory name to be created as well as the 
name of the created file (using up to 127 
characters). Parameters can be specified in the 
entry with the “%” character (p. 152).
(7) [FTP Upload Test] 
Clicking [Exec] initiates an upload test based on the 
settings currently entered. Only one JPEG image is 
uploaded. It is not necessary to click [Apply].
After entering a password, first click [Exec], then 
[Apply] the password.
E-mail Notification
(1) [Notification] 
Select [Text Only] or [Text with Image] as the content 
of notification. If [Upload] is set to [Upload Disabled], 
[Text with Image] will not be available. 
(2) [Copy E-mail Settings]
Copy the mail settings used in [Maintenance] > [Log 
Notifications] (p. 77).
(3) [Mail Server Name] 
Enter the host name or IP address of the SMTP server 
(using up to 63 characters). 
(4) [Mail Server Port] 
Enter the port number of the SMTP server (factory 
default setting is [25]).
(5) [Sender (From)] 
Set the e-mail address of the sender (using up to 63 
characters).
(6) [Recipient (To)] 
Set the e-mail address of the recipient (using up to 63 
characters).
(7) [Authentication] 
Select [None], [POP before SMTP] or [SMTP-AUTH] 
for the e-mail authentication method. Set an appropriate method according to the 
authentication method used by the SMTP server to 
send to. 
[User Name], [Password], [POP Server] 
If [POP before SMTP] is selected as the e-mail 
authentication mode, enter the user name and 
password as well as the host name or IP address of 
the POP server required for authentication. 
[User Name], [Password]
If [SMTP-AUTH] is selected as the e-mail 
authentication method, enter the user name and 
password required for authentication. 
(8) [Subject] 
Enter the subject of the e-mail to be sent using up to 
31 ASCII characters. 
(9) [Message Body] 
Enter the message (text) of the e-mail to be sent using 
up to 255 ASCII characters. Parameters can be 
specified with the “%” character (p. 152).
(10)[E-mail Notification Test] 
Clicking [Exec] initiates an e-mail notification test 
based on the settings currently entered. It is not 
necessary to click [Apply].
After entering a password, first click [Exec], then 
[Apply] the password. 
						

							58
Video Server
(1) [Maximum Number of Clients] 
Set the maximum number of clients that can be 
connected to the camera at the same time. Up to 30 
clients can be set. 
If 0 is set, connection is prohibited except for the 
Administrator. 
(2) [Camera Control Queue Length] 
Set the maximum queue length for clients requesting 
camera control privilege from the viewer. The 
maximum number is 30. Enter an integer from 0 to 30. 
If 0 is set, camera control is prohibited except for the 
Administrator. 
(3) [Maximum Connection Time (sec.)] 
Set the time in seconds during which an individual 
client can connect to the camera. The maximum 
number is 65535. Enter an integer from 0 to 65535. If 0 
is set, the connection time becomes unlimited. 
(4) [Camera Control Time (sec.)] 
Enter the maximum time VB Viewer can retain camera 
control privileges. The maximum number is 3600. 
Enter an integer from 1 to 3600. Audio Server
(1) [Audio Transmission from the Camera] 
When [Enable] is selected, the audio input through the 
microphone attached to the camera can be 
transmitted to the Viewer. 
(2) [Input Volume] 
Set the volume of input for the microphone connected 
to the camera in the range of 1 to 100. The greater the 
value, the larger the input volume becomes. 
(3) [Voice Activity Detection] 
If [Enable] is selected, the audio transmission is 
stopped temporarily when no audio is output. This 
way, the load of the applicable network can be 
reduced. 
(4) [Audio Input] 
Set the microphone input. Select [Line In], 
[Microphone In (dynamic microphone)] or 
[Microphone In (condenser microphone)]. 
[Server] 
Setting the Video Server, Audio Server, HTTP Server, FTP Server and 
WS-Security
The following can be set here. 
 Video Server
Set the video transmission from the camera. 
Server
Set the audio transmission from the camera. 
Server
Set the authentication method, and HTTP port 
number. 
Server
Configure settings for FTP server use.
S-Security
Configure settings for checking the time with WS-
Security.
Caution
Switch line in and microphone in on each setting page 
according to the specification of the microphone. 
Using the wrong input may damage the camera and/or 
microphone. Be sure to configure settings correctly. 
Important
 Video and audio can be distributed to up to 30 clients. 
However, when there are many clients or they are connected 
to the camera over an SSL connection, the video frame rate 
may slow down and the sound may drop out if audio 
reception from the camera is enabled.
 The volume, sound quality, etc., may change depending on 
the characteristics of the microphone used. 
 If the [Input Volume] settings are changed after setting volume 
detection, check the detection setting again. 
 The video and audio may not be synchronized.


 
						

							[Server] Setting the Video Server, Audio Server, HTTP Server, FTP Server and WS-Security
59
Setting Page
3
HTTP Server
(1) [Authentication Method] 
Set the authentication method used with the HTTP 
server to [Basic Authentication] or [Digest 
Authentication]. 
(2) [HTTP Port] 
Set the HTTP port number to 80 or in the range of 
1024 to 65535. 
Normally [80] (factory default setting) is used. 
(3) [HTTPS Port] 
Set the HTTPS port number to 443 or in the range of 
1024 to 65535. 
Normally [443] (factory default setting) is used. 
FTP Server
(1) [Use FTP Server]
Set FTP Server to [Disable] or [Enable].
WS-Security
(1) [Check Time on Authentication]
Select whether to check the time information in data 
sent from the client by selecting [Check] or [Do not 
check].
 The audio may be temporarily interrupted, depending on the 
performance of the computer and the network environment.
 The audio may be interrupted if anti-virus software is 
enabled.
 Communication may be temporarily interrupted, cutting off 
the audio, if the LAN cable is unplugged and plugged in 
again. If this occurs, reconnect from the Viewer.
Important
If the setting of [HTTP Port] or [HTTPS Port] is changed, the 
camera may become inaccessible from the active web 
browser. Check beforehand the precautions in “Important” in 
“[Reboot Item] Setting Items Requiring Rebooting” (p. 76). 
						

							60
Video Record Setting
(1) [Video Record Action]
Select the destination of a video recorded when an 
event occurs. To record to a server selected on the 
[Upload] in the setting page, select [Upload] and to 
record to a memory card inserted in the camera, 
select [Record to Memory Card].
Note
The size and format of video recorded according to the [Video 
Record Action] settings are as follows:
Settings must be made in the above setting page to make 
an actual video recording.Volume Detection
(1) [Volume Detection Event] 
Set volume detection to [Disable] or [Enable]. 
(2) [Detect Criteria] 
Set the criteria for generating volume detection events 
to [The reference volume level or above] or [The 
reference volume level or below]. 
(3) [Reference Volume Level] 
Set the reference volume level for detection in the 
range of 1 to 100. 
Set the reference volume level by performing an 
actual test while checking [Current Volume Level] 
before configuring the setting.
(4) [Current Volume Level]
The current volume level appears on the status bar.
The level set in [Reference Volume Level] is indicated 
by a red mark.Volume below the reference level 
appears in blue, that above the reference level 
appears in red.
(5) [Detect Criteria Duration (sec)] 
Set the duration of the detect criteria in the range of 0 
to 10 (sec.). When the status meeting the detect 
criteria has continued for the duration or longer, an 
ON event is generated. 
(6) [ON Event Operation] 
Select the operation to be performed upon an ON 
event. If [Enable] is selected, (9) [Preset], (10) [Video 
Record] and (11) [E-mail Notification] will be executed 
according to their settings upon an ON event. 
(7) [OFF Event Operation] 
Select the operation to be performed upon an OFF 
event. If [Enable] is selected, (9) [Preset], (10) [Video 
Record] and (11) [E-mail Notification] will be executed 
according to their settings upon an OFF event. 
[Event] 
Setting Video Record, Volume Detection, External Device Output/Input and 
Timer
The following can be set here. 
 Video Record Setting
Set where video is recorded when an event 
occurs.
 Volume Detection
Set the operation to be performed at the time of 
volume detection. 
 External Device Output
Set external device output.
 External Device Input
Set the operation to be performed when an event 
is triggered by input from an external device. 

Set timer events. 
Important
When using the upload function, or recording to the memory 
card, do not change the settings in the [Setting Page]. Doing so 
may result in the upload function or the recording to memory 
card to stop.
[Video Record 
Action] settingsApplied video formatApplied video size
[Upload] [Upload] > [Video 
Format] settingsWhen the video format is 
[JPEG], [Video] > [JPEG] > 
[Video Size: Upload / 
Memory card]
When the video format is 
[H.264(1)], [Video] > 
[H.264(1)] > [Video Size] [Record to 
Memory Card][Memory Card] > 
[Video Format] 
settings