Canon network camera VBS31D User Manual

[Access Control] Setting User Access Privileges
61
4
Setting Page
IPv6 Host Access Restrictions
(1) [Apply Host Access Restrictions] 
Set IPv6 host access restrictions to [Disable] or 
[Enable]. 
(2) [Default Policy] 
If IPv6 host access restrictions are applied, select 
[Authorize Access] or [Prohibit Access] for the default 
policy. 
(3) [Prefix / Prefix Length] 
Create a list of permitted hosts and restricted hosts 
and set IPv6 address access for each host to [Yes] or 
[No]. 
You can specify the...

62
IPsec 
(1) [IPsec] 
Key settings for use with IPsec can be selected as 
[Auto Key Exchange] or [Manual].
Auto Key Exchange Settings
(1) [IPsec SA Encryption Algorithm] 
Set the IPsec SA encryption algorithm to [AES-
>3DES], [AES->3DES->DES] or [AES->3DES->DES-
>NULL]. 
The specified algorithm will be checked for an 
applicable encryption algorithm starting from the left. 
(2) [IPsec SA Authentication Algorithm] 
Set the IPsec SA authentication algorithm to 
[HMAC_SHA1_96] or [HMAC_SHA1_96->...

[IPsec] Setting IPsec
63
4
Setting Page
(8) [IKE Pre-Shared Key] 
Enter the pre-shared key for IKE (auto key exchange) 
(up to 127 characters). 
Note
If auto key exchange is used, it will take approximately 5 to 10 
seconds before communication with the camera starts. 
IPsec Set (Manual) 
IPsec Sets 1 to 5 are available, and you can specify IPsec 
settings for one communication device for each IPsec Set. 
(1) [IPsec Set] 
Set IPsec Set to [Disable], [Enable in IPv4] or [Enable 
in IPv6]. 
(2) [IPsec...

64
identifying the SA, be careful not to specify an 
inbound SPI whose value is already used in the SPI for 
other ESP. 
zIf [Security Protocol] was set to [AH] or [ESP and AH] in 
(5), (16) [SA AH Authentication Algorithm] to (20) [SA 
AH SPI (inbound)] must be set. 
(16)[SA AH Authentication Algorithm] 
Set the AH authentication algorithm to 
[HMAC_SHA1_96] or [HMAC_MD5_96] according to 
the authentication algorithm supported by the device 
to connect to. 
(17)[SA AH Authentication Key (outbound)] 
Set...

65
Setting Page
4
Certificates
(1) [Create Self-Signed Certificate] 
After entering each of the following settings, click 
[Exec] to create a self-signed certificate. Follow the 
instructions in the message and reboot. The certificate 
created will take effect after rebooting. 
Note
Creating a certificate takes time, so it is recommended that you 
stop video transmission and upload processes.
(2) [Certificate Status] 
If no certificate is installed, [Not Installed] will appear. 
If a certificate is...

66
(6) [Display Server Certificate Details] 
Click [Exec] to view the details of the certificate. 
(7) [Display Self CA Certificate] 
Used for the purpose of testing SSL communications, 
but otherwise not normally used. 
(8) [Backup] 
Click [Exec] to perform a backup of the certificates 
and private key. This operation can only be performed 
via SSL communications. 
(9) [Restore] 
Installs the certificates and private key from 
backup. Click [Browse] to select the backup file, 
then click [Exec]. This...

67
Setting Page
4
802.1X Authentication
(1) [802.1X Authentication]
Set 802.1X authentication to [Disable] or [Enable].
Initially, if [802.1X Authentication] in [802.1X] is set to 
[Enable] and [Apply] clicked, [Before changing the 
setting, set 802.1X authentication to “Disable”. ] will 
be displayed, and input for setting changes, 
certificate installation/deletion, etc. will be unavailable. 
To change settings, first set [802.1X Authentication] to 
[Disable] and click [Apply]. Settings input will be...

68
(5) [Delete Certificate]
Deletes all installed CA certificates, client certificates, 
and client private keys.
Only “CA Certificate” is displayed when [Authentication 
Method] is set to [EAP-TTLS] or [EAP-PEAP], but any 
installed client certificates and client private keys are also 
deleted.
Important
 If any CA certificates, client certificates, and client private 
keys already exist, they are discarded and new versions are 
installed.
 An error occurs if the format of the certificate or private key...

69
Setting Page
4
Memory Card Operations (unmount status) 
(1) [Mount/Unmount] 
In unmount status, [Mount] will appear. Click [Mount] 
to mount the memory card. 
Note
microSD, microSDHC, and microSDXC memory cards can be 
used with the camera.
When a memory card is inserted in the card slot, it is mounted 
automatically. It is also mounted automatically if inserted in the 
camera at the time of booting. 
For inserting and removing the memory card, see “Installation 
Guide” > “Using a Memory Card”. 
(2)...

70
Memory Card Operations (mount status) 
(1) [Mount/Unmount] 
In mount status, [Unmount] will appear. Click 
[Unmount] to unmount the memory card. 
(2) [Operation Settings], [Video Format], [Pre-event 
Buffer], [Post-event Buffer], [Overwrite videos]
These settings are the same as in “Memory Card 
Operations (unmount status)”.
(3) [Delete Videos] 
Click [Exec] to delete videos from the memory card. 
During deletion, an indicator will appear to the right of 
[Exec]. 
Note
 It may take 40 minutes or more...