Canon network camera VBM741 LE User Manual

Setting Page
4
91
Settings for clients that can connect to a video server.
[Maximum Number of Clients]
Enter the maximum number of clients that can  be connected to the camera at the same time.
If set to [0], only administ rators will be able to connect.
[Camera Control Queue Length]
Enter the maximum queue length for clients reques ting camera control privileges from the Viewer.
If set to [0], only Admin Viewer and Admin Tools can queue for camera control.
[Maximum Connection Time (sec.)]
Enter the...

92
Settings for audio transmission from the camera to the computer, and audio reception from the computer to the camera.
[Audio Transmission from the Camera]
Select to transmit audio from the microph one connected to the camera to the Viewer.
[Voice Activity Detection]
Select whether to detect when there is  no sound coming from the microphone.
When set to [Enable], audio data transmission will pause while th ere is no sound input from the camera. This can reduce the 
load on the network used.
[Audio...

Setting Page
4
93
Set the video and audio transmission using RTP.
RTP Server
Enable RTP, and set the RTSP authentication method and port number.
[RTP]
Select this to enable or disable RTP.
[RT SP Authentication Method]
Select an authentication method for RTSP. Since the RTSP aut hentication method is configured independently of the HTTP 
authentication method, you need to  configure each authentication method.
[RT SP Port]
Enter the RTSP port number.
Normally use [554] (factory default setting).
Audio...

94
RTP Streaming 1 to 5
You can set each stream for RTP stream transmission in an RTP Streaming 1 to RTP Streaming 5 session.
[Video  Size]
Select the video format (JPEG or H.264 ) and video size for the RTP stream.
The video sizes for JPEG will vary depending on the [Video Size Set] settings (P. 72).
The video sizes for H.264 will be determined according to the  [H.264(1)] and [H.264(2)] settings in [Video Settings] (P. 73).
In addition, [H.264(1)] and [H.264(2)]  cannot be set for multiple RTP...

Setting Page
4
95
 Regardless of the [Server] > [Audio Serve r] > [Audio Transmission from the Camera] se tting, RTP streaming audio will be used. 
However, to use audio settings, select [Enable] for [Aud io Transmission from the Camera] and configure the settings.
R11M641M741 

96
Settings for uploading video via HTTP or FTP when an event is triggered.
Use [Server] > [Server Settings] (P. 89) to configure  HTTP server and FTP server settings for uploading.
Video Record Setting
When an event is triggered, sets  whether to upload camera video with HTTP or FTP or to record the video to a memory card.
These can also be set with the [Memory Card] submenu (P. 101 ) and will be reflected in [Video Record Setting] here.
[Video Record Action]
Select [Upload] to upload video.
General...

Setting Page
4
97
[Upload]
Select whether to upload with HTTP or FTP.
[Video Format]
Select the video format for up load. [H.264(2)] cannot be used.
Video size and quality of the uploaded video fo llow the settings in [Video Settings] (P. 72).
[Frame Rate]
Enter the maximum frame rate of video to be up loaded when [Video Format] is set to [JPEG].
[Pre-event Buffer (number of  frames)] (JPEG)/ [Pre-event  Buffer (sec)] (H.264(1))
Enter the number of frames or seconds of  video to be buffered before the...

98
[Notification]
Select whether to only send event information notifications or notifications with attached videos when using HTTP upload.
[URI]
Enter the HTTP server URI to which to upload.
[User Name], [Password]
Enter the user name and password required for authentication.
Digest authentication is not supported.
[Proxy  Server]
If using a proxy server, enter the host name or IP address of the proxy server.
[Proxy Port]
If using a proxy server, enter the port number of the proxy server.
[Proxy User...

Setting Page
4
99
FTP Upload
Settings for the FTP upload function when [Upload] is set to [FTP Upload].
[Notification]
This is set to [Video data upload with FTP].
[FTP  Server]
Enter the host name or IP address of FTP server.
[User Name], [Password]
Enter the user name and password required for authentication.
[PA SV Mode]
Select whether to use PASV mode when connecting to an FTP server.
[File Upload Path]
Enter a remote path (directory name) for video files to be uploaded to.
[File Naming]
Select a...

100
[User Setting]
Video is uploaded according to the file  naming method specified in [Subdirectory Name to Create] and [File Name to 
Create].
[ Subdirectory Name to Create], [File Name to Create]
If file naming is set to [User Setting],  enter the subdirectory name to be created  as well as the name of the created file.
Parameters can be specified in the entry with the “%” character (P. 252).
[FTP Upload Test]
Clicking [Exec] initiates an upload test  based on the settings currently entered.
Only a...