Canon network camera VBM720F User Manual

							Notes on Operating Environment
21
1
Before Use
„Enabling the Sound Function to Use Audio
In Windows Server 2008/Windows Server 2012, the sound 
function is disabled by default. 
To receive audio with the Viewer, follow the steps below to 
enable the sound function.
Note
If [Control Panel] is in the classic view, double-click [Sound]. 
Important
Note that when IE Enhanced Security Configuration is turned
back on, the [Do not save encrypted pages to disk] checkbox
also becomes enabled.
1Open [Control Panel] and click [Hardware]. 
2Click [Sound]. 
3When the [Audio Service Not Running] message 
appears, click [Yes]. 
4The [Sound] dialog box appears. 
Click the [Playback] tab to confirm that an audio device 
has been installed. (If no audio device is installed, refer 
to your PC manual.) 
						

							22 
						

							Chapter 2
Initial Settings
❏Preparing the Camera for Use
❏Installing the Necessary Software
❏Initial Settings
❏Access the Top Page of the Camera to Check Video 
						

							24
▼
▼
▼
▼
▼
▼
▼
Preparing the Camera for Use
Performing Initial Settings for the Camera
Before installing the camera, read this chapter and use the Camera Management Tool  to 
configure the IP address. 
“Installing the Necessary Software” (p. 26)
“Making Initial Camera Settings” (p. 28) 
Checking Images
When initial settings are complete, access the camera via a web browser and check the 
video using the VB Viewer.
“Access the Top Page of the Camera to Check Video” (p. 31)
Installing the Camera
Install the camera to suit the operating environment it will be used in.
“Installation Guide”
Setting the Camera Angle
Use the Camera Angle Setting Tool to set the camera angle via PC operation. 
“Installing the Necessary Software” (p. 26)
“Chapter 3 Camera Angle Setting Tool”
Configuring the Camera from the Setting Page
The setting page lets you configure basic camera settings, network operations, user 
registration, and access restrictions.
“Chapter 4 Setting Page”
Using Admin Tools
Admin Tools let you set viewing restrictions, make preset settings, and make settings for 
using intelligent functions. In addition, you can review logs to check on the cameras 
operation status.
“Chapter 5 Admin Tools”
Using Admin Viewer/VB Viewer
The cameras built-in Admin Viewer/VB Viewer features an Admin Viewer for 
administrators and a VB Viewer for guest users. Use the VB viewer to check distribution to 
guest users and Admin Viewer to check all operations.
“Chapter 6 Admin Viewer/VB Viewer” 
						

							Preparing the Camera for Use
25
2
Initial Settings
Operating
If an error message appears or the camera fails to operate correctly, see the error 
message and log message information in “Chapter 7 Appendix”.
“Chapter 7 Appendix”
Important
Before starting operations, make sure that the setting page and Admin Tools settings are functioning correctly. 
						

							26
Install the following software to perform initial settings for the camera.
 Camera Management Tool: Software required for performing initial camera settings and maintenance
 Admin Tools Certificate: An electronic certificate that is required for using Admin Viewer and Admin Tools
 Camera Angle Setting Tool: Software to use for camera angle adjustments when installing the 
camera
 .NET Framework 3.5 SP1/.NET Framework 4.5: The execution environment required for network camera software (not 
required if already installed on the PC)
You can perform either an Easy Installation or a Custom Installation of the software.
Note
 All computer users will be able to use Admin Viewer and Admin Tools if the Admin Tools certificate was installed by the installer.
 Select [Custom Installation] and install only the “Admin Tools Certificate” if you intend to use the Admin Viewer and Admin Tools on a PC 
other than the one where the Camera Management Tool is installed.
 If you install the software with Easy Installation, the Camera Angle Setting Tool that is not used with VB-H43/VB-M42 is also installed. If 
you do not want to install the Camera Angle Setting Tool because you are using only VB-H43/VB-M42 cameras, perform a [Custom 
Installation] and clear the checkbox for the Camera Angle Setting Tool.
The installation screen appears.
Note
If the [User Account Control] screen appears, click [Yes] or 
[Continue].
[Easy Installation]: Camera Management Tool, Admin 
Tools certificate and Camera Angle Setting Tool are 
installed.[Custom Installation]: The user can select and install 
desired software.
The User License Agreement screen appears.
Installation starts.
Installing the Necessary Software
1Insert the Setup CD-ROM included in the camera in 
the disc drive on the PC.
2After confirming that all other applications have been 
closed, click the [Start] menu > [My Computer].
3Double-click the CD-ROM icon > [Applications] folder 
> [VBToolsInstall.exe].
4Select the installation method.
5After selecting [Easy Installation], click [Next] and after 
selecting [Custom Installation], select the checkboxes 
of the software you want to install and click [Next].
6Read through the user license agreement and click 
[Yes] if you accept it. 
						

							Installing the Necessary Software
27
2
Initial Settings
The Camera Management Tool and Camera Angle 
Setting Tool icons appear on the desktop.
7When the installation complete screen appears, click 
[Exit] or [Reboot]. 
						

							28
To use the camera, you must first set the network settings 
for the camera and then establish a network connection 
between the camera and a computer. Use Camera 
Management Tool for these settings.
This section will explain, in addition to network settings, 
how to set the camera name, the date and time and other 
settings. It will also explain how to use the Camera 
Management Tool to make initial camera settings.
Note
 For details on using Camera Management Tool, please refer to 
“Camera Management Tool User Manual”.
 The settings made here will be reflected in the settings on the 
Setting Page (p. 45).
Launch the Camera Management Tool
Launch the Camera Management Tool that was installed 
onto the computer from the setup CD-ROM.
Please refer to “Installation Guide” > “Connecting the 
Camera”.
Camera Management Tool launches and the [Camera 
Search Settings] dialog box appears.
The Camera Management Tool main screen will 
appear.
Searching for Cameras and Setting up 
Networks
This will explain network settings so you can search for 
network connected cameras and connect to them from a 
computer.
The examples will be for setting one camera. The Camera 
Management Tool, however, can set multiple cameras at 
the same time.
Detected cameras will appear in the camera list.
The [Basic Camera Settings] dialog box appears.
(1) [IPv4 Address Setting Method]
Select the method for setting the IPv4 address.
If [Manual] is selected, directly enter values that suit 
the environment in which the camera is used.
If [Auto (DHCP)] is selected, the value automatically 
acquired from the DHCP server will be entered in [IPv4 
Address], [Subnet Mask] and [IPv4 Default Gateway 
Address].
Making Initial Camera Settings
1Connect the camera and computer to the network and 
turn on the power.
2Double-click the [Camera Management Tool] icon on 
the desktop.
3Enter the factory default password (“camera”) into 
[Administrator Password] and click [OK].
1Click the [Search Camera] icon.
2Select a camera in the camera list and click the [Basic 
Camera Settings] icon.
3Set each of the [Network] items.
(1)
(3)
(4)
(5) (2)
(6)
(7) 
						

							Making Initial Camera Settings
29
2
Initial Settings
(2) [IPv4 Address]
If you selected [IPv4 Address Setting Method] > 
[Manual], enter a fixed IPv4 address.
(3) [Subnet Mask]
If you selected [IPv4 Address Setting Method] > 
[Manual], enter the designated subnet mask values for 
each network.
(4) [Enter a default gateway address] checkbox
Select this to manually set the default gateway 
address.
(5) [IPv4 Default Gateway Address]
Be sure to set this if you select [IPv4 Address Setting 
Method] > [Manual] and connect to the camera with a 
different subnet than that of the viewer.
(6) [AutoIP]
Select this to enable or disable AutoIP.
(7) [IPv4 Address (AutoIP)]
When [Enable] is selected for [AutoIP], an 
automatically set IPv4 address is displayed.
The camera will restart and the settings will take 
effect.
When you click [OK], other settings in ([Password], 
[Date and Time], [Camera], [Video]) [Basic Camera 
Settings] will also take effect.
Set the Password, Date and Time, Camera 
Name and Video
Set basic camera information, such as the camera name, 
administrator password and date.
Once you have entered information for each item, click 
[OK].
„Password Setting
Click [Password] and set the administrator password.
„Date and Time Settings
Click [Date and Time] and make settings such as the 
camera date and time setting method, time zone, and 
daylight saving time.
For details on each item, please refer to “Setting” (p. 54) 
in “[Date and Time] Setting Date and Time”.
„Camera Name Setting
Click [Camera] and set the camera name displayed in the 
viewers and other software.
For setting details, please refer to “Camera Name” (p. 56) 
in “[Camera] Setting Initial Camera Settings and External 
Device Name”.
4Click [OK].
Important
To ensure system security, be sure to change the administrator 
password. Do not forget the new password. 
						

							30
„Video Settings
Click [Video] and configure the size and quality settings of 
the video transmitted from the camera.
For setting details, please refer to “[Video] Setting Video 
Size, Quality and Frame Rate” (p. 61).
Registering Camera’s IP Address to 
Trusted Sites
With Internet Explorer 9 or greater and Windows Server 
2008/Windows Server 2012, Internet Explorer’s security 
level for Internet and intranet sites is set to [High] by 
default.
As a result, it may be necessary to register the camera’s 
IP address as a trusted site to access the Admin Viewer/
VB Viewer, Setting Page or Admin Tools.
A confirmation message appears.
The camera will be registered as a trusted site for 
Internet Explorer.
Note
The registered information will be loaded when Internet Explorer 
is restarted. Close and restart Internet Explorer if it is running.
1Select a camera from the camera list.
2Click [Maintenance] menu > [Add to Trusted Sites].
3Click [Yes].