Canon network camera VBM641V User Manual

Setting Page
4
61
Common Setting Page Operations
This section explains basic Setting Page operat ions, and operations common to all Setting Pages.
Applying Changes to Settings
When a setting is changed on the Setting Page, [Apply] show n on the top right and bottom right of the Setting Page 
changes from grayed-out to blue.
Click [Apply] in this state to  apply the changed settings.
Click [Clear] to revert to  the previous settings.
Setting Changes Requiring Rebooting
Items that require the camera to...

62
About Each Setting Page
This section will give an overview of each item in Setting Menu and each list of submenus.
Each of the [Basic Settings], [Video and Audio]/[Video],  and [Video Record] menus has a [Video Settings] submenu, but 
the functions are all common. The functions can be set in any  of the menus and the settings will be reflected in all of the 
[Video Settings] submenus.
 Network (P. 64) Network settings for connecting to the camera.
 Password (P. 68)
Use this to change the administrator...

Setting Page
4
63
 Video  Settings (P. 72)
 Upload (P. 96) Settings for uploading video via HTTP or FTP when an 
event is triggered.
 Memory Card (P. 101) Settings for recording video to a memory card when an 
event is triggered.
The settings of this item are the same as those of the 
[Memory Card] menu. The sett ings can be made with 
either of them.
 E-mail Notification (P. 102) Settings for sending an e-mail notification to a specified 
recipient when an event is triggered.
Video Record
Event...

64
Network settings for connecting to the camera.
LAN
Set the LAN communication method and size of video transmitted from the camera.
[LAN Interface]
Select the interface suited to the device for connecting to the camera. Generally use [Auto].
[Maximum Packet  Size]
Enter the maximum packet size to be transmitted by the camera. Normally there is no need to change the default setting of 
1500.
A setting of 1280 or greater is necessary when using IPv6.
When using ADSL, setting a slightly lower va lue may...

Setting Page
4
65
For [Manual], enter a fixed IPv4  address into [IPv4 Address].
For [Auto (DHCP)], the settings acquired from the DHCP server will be automatical ly entered in [IPv4 Address], [Subnet 
Mask] and [IPv4 Default Gateway Address].
[IPv4 Address]
When [IPv4 Address Setting Method] is set  to [Manual], enter a fixed IPv4 address.
The IP address cannot start wi th 127., such as 127.0.0.1.
[ Subnet Mask]
When [IPv4 Address Setting Method] is set to [Manual], ent er the designated subnet mask...

66
[IPv6 Address (Manual)]
Enter a fixed IPv6 address if you set the address manually.
[Prefix Length]
Enter a prefix length if [Disable] is specified in [Auto (RA)].
[IPv6 Default Gateway Address]
Enter a default gateway address if [Disable] is specified in [Aut o (RA)]. Be sure to set this when connecting the camera to a 
different subnet from that of the Viewer.
[IPv6 Address (Auto)]
If [Enable] is specified in [IPv6] and [Enable] is specified in [Auto (RA)] and  [Auto (DHCPv6)], then the...

Setting Page
4
67
[Host Name]
You can register the camera host name in  name server using alphanumeric characters.
Do not use “_” (underscore) in the hos t name in Internet Explorer 8/9/10/11.
[Host Name Registration with DDN S]
When you enter a name into [Host Name] and select [Enable] , the host name will be registered in the name server.
Registering the host name to DDNS is useful when operating with [IPv4 Address Setting Method] set to [Auto (DHCP)] 
(P. 64). DNS server registration settings  must be...

68
In order to prevent users, other than administrators, from changing the system, change the administrator password from the 
default password.
Administrator Password
Change the administrator password.
[Password]
Enter the administrator password in alphanumeric characters (spaces or printable characters).
The factory default setting is “camera”.
If the Admin Viewer, Admin Tools,  etc., are connected, terminate the c onnection before changing the password.
[Confirm Password]
Enter the same password as...

Setting Page
4
69
Camera date and time settings.
Current Date and Time
The date and time set in the camera are shown.
Setting
Set the date and time setting  method, time zone and daylight  saving time for the camera.
[ Setting Method]
Select the date and time setting method.
The settings are configured as follows depending  on the setting configured in [Setting Method].
[ Set manually] 
Set the desired date and time in [Date] and [Time].
Set the time in 24-hour format  in  order.
[ Synchronize with NTP...

70
[Use DHCP]
The camera time is synchronized with the time of the NTP server at the address acquired from the DHCP server. The 
acquired NTP server address ap pears in [NTP Server (DHCP)].
In order to set [Use DHCP], you must change [Network] >  [IPv4] > [IPv4 Address Setting Method] to [Auto (DHCP)] 
(P. 64).
[Use DHCPv6]
The camera time is synchronized with the time of the NTP  server at the address acquired from the DHCPv6 server. 
The acquired NTP server address a ppears in [NTP Server (DHCPv6)].
In...