Canon network camera VBC500VD User Manual

1-27
Setting HTTP/FTP Upload and E-mail Notification (Upload)
1
1Detailed Settings
(6) [Authentication]
Select [ None], [POP before SMTP ] or [SMTP-AUTH ] as the e-mail authentication mode. 
Set an appropriate mode according to the authent ication mode used by the SMTP server to 
send to. 
[User Name], [Password], [POP Server] 
If [POP before SMTP ] is selected as the e-mail authentication mode, enter the user name, 
password, and host name or IP address of  the POP server, required for authentication....

1-28
Setting the Image Server, Audio Server and HTTP 
Server (Server)
Image Server
(1) [Maximum Number of Clients]Set the maximum number of clients that can be connected to the camera at the same time. 
Up to 30 clients can be set. If 0 is set, connect ion is prohibited except for Admin Viewer. 
(2) [Camera Control Queue Length] Set the maximum queue length of requests for the camera control privilege from clients. The 
maximum number is 30. Enter an integer from 0 to 30. If 0 is set, camera control is...

1-29
Setting the Image Server, Audio Server and HTTP Server (Server)
1
1Detailed Settings
Audio Server
(1) [Audio Transmission from the Camera] 
When [ Enable] is selected, the audio input through the microphone attached to the camera 
can be transmitted to VB-C500 Viewer. 
(2) [Input Volume] Set the volume of input sound in a range of 1 to 100. The greater the value, 
the larger the input volume becomes. 
(3) [Voice Activity Detection] If [Enable ] is selected, the audio tr ansmission size is reduced...

1-30
Setting the Image Server, Audio Server and HTTP Server (Server)
Caution
Switch [Line In] and [Microphone In] on each setting page according to the 
specification of the microphone ( P. 1-29).
If a wrong input is used, the camera or microphone may be damaged. Be sure to set 
the correct input. 
Note
z The volume, sound quality, etc., may change depending on the characteristics of the 
microphone used. 
z To output audio from the audio output terminal of the camera, send audio from VK Viewer. 
Audio...

1-31
Setting the Image Server, Audio Server and HTTP Server (Server)
1
1Detailed Settings
HTTP Server
(1) [HTTP Port] 
Set the HTTP port number in a range of 80 and 1024 to 65535. 
Normally [ 80](factory setting) should be used. 
(2) [Global Address for the Web Page] If a fixed global address is assigned to the camera using the NAT function of the router 
(  P. 4-12), set the global address and port number here. If [ IP Address] is selected, enter 
the specified IP address in the [ IP Address] field. If...

1-32
Setting the Image Buffer, Motion Detection, 
Audio Playback and Interval Timer (Event) 
Image Buffer 
(1) [Frame Rate]Set the frame rate that applies when image is  temporarily saved in the image buffer when an 
event occurs.
(2) [Pre-event Buffer (number of image frames)]  Set the number of images to be buffered before the event. 
(3) [Post-event Buffer (number of image frames)] Set the number of images to be buffered after the event. You can set the following items. 
z
Image Buffer 
Set the items...

1-33
Setting the Image Buffer, Motion Detection, Audio Playback and Interval Timer (Event)
1
1Detailed Settings
Motion Detection 
(1) [Motion Detection Event]
Whether motion detection events are enabled/disa bled is shown. The value of this item can 
be changed using Motion Detection Se tting Tool in VBAdmin Tools ( P. 2-7). When motion 
detection events are enabled, event notification  to the viewer is performed according to the 
displayed motion detection event of this camera such as Admin Viewer.
(2)...

1-34
Setting the Image Buffer, Motion Detection, Audio Playback and Interval Timer (Event)
(7) [Audio Playback at ON Event] Select the audio playback operation to be performed upon an ON event. If [Enable ] is 
selected, the sound specified under [ Sound Clip] will be played when the mode changes to 
[ Detected] (ON event). 
(8) [Audio Playback at OFF Event] Select the audio playback operation to be performed upon an OFF event. If [ Enable] is 
selected, the sound specified under [ Sound Clip] will be...

1-35
Setting the Image Buffer, Motion Detection, Audio Playback and Interval Timer (Event)
1
1Detailed Settings
(2) [ON Event Operation]
Select the operation to be performed upon an ON event. If [ Enable] is selected, (4), Upload, 
(5) and E-mail Notification are displayed. W hen an ON input is received from an external 
device (ON event), the processes set in (4) and (5) are performed. 
(3) [OFF Event Operation] Select the operation to be performed upon an OFF event. If [ Enable] is selected, (4),...

1-36
Setting the Image Buffer, Motion Detection, Audio Playback and Interval Timer (Event)
Interval Timer 
(1) [Interval Timer Event]
Select whether to [ Enable] or [Disable] timer events.If [ Enable] is selected, (2), Timer 
Interval, (3), Upload and (4), E-mail Notification are displayed. 
(2) [Interval of the Timer] Select a desired timer interval from  the pull-down menu in a range of [1 sec. ] to [24 hours ]. 
(3) [Upload] Select the upload operation. If [ Enable] is selected, upload is performed at...