Canon network camera VBC500D User Manual

5-15
List of Log Messages
Appendix
B403 Settings change failed [crit]
„HTTP Server Messages 
H143  User name specification error [notice]
H144 Password specification error [notice]
H145 Connection denied due to host access limitation [notice] Description  cannot set config[%1] (B403)
%1 Error number
Meaning  The settings could not be updated. The audio server stops. 
Countermeasure  If the problem persists after rebooting, the camera is faulty. Arrange 
for servicing. 
Description  (http_auth.c.XXX)...

5-16
List of Log Messages
„System Messages
S004  Starting and stopping of system [info]
S005  System settings changed [info]
S240 Camera error [warning]
S306 Error on saving settings [err]
S307 Error on saving settings [err] Description %1 webview (S004)
%1 Starting or stopping. 
Meaning  The video server (webview) has started or stopped.
Description  (vbadmin.c.XXX) System settings updated (S005) Meaning  Settings not requiring rebooting were changed. 
Description  serviceman call (S240) Meaning  The...

5-17
Appendix
List of VB-C500 Viewer Messages
Messages Displayed in the Information Field 
Messages displayed in the information field of the viewer are classified into the following three 
types. 
„ Information Messages
*When the mouse is brought over any of the following GUI parts, a corresponding message appears.
Icon Category Explanation 
 
Information 
Messages Help messages on various buttons, pull-down 
lists, etc., and zoom, frame rate and other 
information from the camera are shown. 
  Warning...

5-18
List of VB-C500 Viewer Messages
„Warning Messages
Switches on camera control privileges. Obtain/release Camera Control button
Switches on/off camera control privileges. Obtain/release Camera Control button
Displays information. Information Field
Message Explanation 
Connection closed by the camera. The camera was disconnected. 
{n}fps Communicating with the camera normally. 
{n}fps Zoom: {z} Communicating with the camera normally. 
Audio connection has been closed. The video session has continued...

5-19
List of VB-C500 Viewer Messages
Appendix
„Error Messages
Message Explanation 
No response from the camera. Connection failed due to an invalid IP 
address, etc. 
The camera is not available because of too 
many users. The connection limit was exceeded. 
Failed to get camera control privilege.  The request for control privileges was 
denied because the camera was being 
used by Admin Viewer, etc. 
The camera is not available for free 
accesses. The camera could not be connected due to 
address...

5-20
Restore Settings 
Since the VB-C500VD/VB-C500D supports various functions, it is recommended that you write 
down the settings for respective functions. If you forgot the settings and want to set the camera 
from the beginning, restore the factory settings first. 
* For the factory settings, see P. 5-23.
Restoring the Settings from th e Maintenance Page in the 
Web Browser 
1. Launch the Web browser and display the menu page from which A access various settings.
To display the Setting Menu page, you...

5-21
Restore Settings
Appendix
4. The camera will be reset to the factory settings. All settings will be reset to the factory se ttings, except for the Administrator password, 
cameras IP address, subnet mask, default gateway address and other network settings, and 
date & time and time zone. 
Initializing with the Reset Switch on the Camera 
If you forgot or dont know the IP address of  the camera or your Administrator password, you 
cannot operate the camera via the network. In this  case, push the...

5-22
Restore SettingsAll settings of the camera, except for the date and time, are initialized. 
Note
If the reset switch is pu shed, the settings will be initialized  including the cameras IP address, 
subnet mask, default gateway address and other network settings. Accordingly, you can no 
longer operate the camera from the PC you were using to connect to the camera before. When 
initializing the camera, use [ VB Initial Setting Tool v5.0.1] installed in your PC to set an IP 
address appropriate for...

5-23
Appendix
List of Factory Settings
The factory settings are shown. If you have changed settings, be sure to write down the new 
settings. 
Item Setting Settings 1
(year/month/day)Settings 2
(year/month/day)
z  User Name (Administrator ID)
z  Administrator password  root
camera
z  Path to Setting pages admin
z LAN
IP Address Setting
IP Address
Subnet Mask
Default Gateway Address
LAN Interface
Maximum Transmission Unit
z IPv6
IPv6
IPv6 Address 
z DNS
Name Server Address 1
Name Server Address 2
Host...

5-24
List of Factory Settings
zCamera Name
Camera Name (alphanumeric 
characters)
z Camera Initial Settings
AE Mode
Slow Shutter
Shutter Speed 
z Camera Control
Digital Zoom
z Day/Night
Mode
Switching Brightness
Response (sec.)
z Installation Conditions
Image Flip
z External Input Device 1
Device Name (alphanumeric 
characters)
z External Input Device 2
Device Name (alphanumeric 
characters)
z External Output Device 1
Device Name (alphanumeric 
characters)
z External Output Device 2
Device Name...