Canon Maxify Mb5020 User Guide

If you select ON, the machine transmits the fax after confirming the dial tone.
Note
•
This setting may not be available depending on the country or region of purchase.
•
Pause time settings
Sets the length of pause time for each when you enter "P" (pause).
•
TTI position
Selects the position of the sender information (outside or inside the image area).
•
Remote RX
Enables/disables remote reception.
If you select  ON, you can specify the remote reception ID.
Remote Reception
•
Color transmission...

Auto print settings•
Received documents
Selects whether to print the received fax automatically when receiving a fax.
If you select  Do not print , the received fax is stored in the machine's memory.
For details on the received fax stored in the machine's memory:
Document Stored in Machine's Memory
•
Activity report
Selects whether to print ACTIVITY REPORT automatically.
If you select  Print, the machine prints ACTIVITY REPORT for the 20 histories of sent and received
faxes automatically.
For...

•Check RX FAX information
If you select  ON, the machine checks whether the recipient's fax machine information matches the
dialed number. If it matches the number, the machine starts to send faxes.
Preventing Mistransmission of Faxes
•
Hook key setting
If you select  Enable, you can use the on hook function.
•
FAX reception reject
If you select  ON, the machine rejects the reception of faxes with no sender information or faxes from
specific senders.
Rejecting Fax Reception
•
Caller rejection
If you...

Print settings•
Prevent paper abrasion
Use this setting only if the print surface becomes smudged.
Important
•
Be sure to set this back to  OFF after printing since it may result in lower printing speed or lower
print quality.
254
 

LAN settings
Important
•
This setting item is for the administrator.
•
Change LAN
Enables either wireless LAN, wired LAN, or access point mode. You can also disable all.
•
Wireless LAN setup
Selects the setup method for wireless LAN connection.
Note
•
You can also enter this setting menu by selecting  WLAN on the HOME screen. In this case, enable
wireless LAN.
When this menu is selected, the machine starts searching for a WPS-compatible access point. If the
machine detects the access point, follow the...

ConnectionActive/InactiveSSIDXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXCommunication modeInfrastructureChannelXXWireless LAN securityInactive/WEP(64bit)/WEP(128bit)/WPA-PSK(TKIP)/WPA-PSK(AES)/WPA2-
PSK(TKIP)/WPA2-PSK(AES)IPv4 addressXXX. XXX. XXX. XXXIPv4 subnet maskXXX. XXX. XXX. XXXIPv4 default gatewayXXX. XXX. XXX. XXXIPv6 addressXXXX: XXXX: XXXX: XXXX:
XXXX: XXXX: XXXX: XXXXIPv6 subnet prefix lengthXXXIPv6 default gatewayXXXX: XXXX: XXXX: XXXX:
XXXX: XXXX: XXXX: XXXXMAC addressXX:XX:XX:XX:XX:XXIPsec...

IPv6 default gatewayXXXX: XXXX: XXXX: XXXX:
XXXX: XXXX: XXXX: XXXXMAC addressXX:XX:XX:XX:XX:XXIPsec settingsEnable (ESP)/Enable (ESP & AH)/Enable (AH)/DisablePre-shared keyXXXXXXXXXXXXXXXXPrinter nameXXXXXXXXXXXXXXXBonjour service nameXXXXXXXXXXXXX
XXXXXXXXXXXXX
XXXXXXXXXXXXX
XXXXXXXXXXXXX
("XX" represents alphanumeric characters.)
◦
AP mode setting list
The list of access point mode settings of this machine is displayed on the touch screen. The following setting items are displayed....

Bonjour service nameXXXXXXXXXXXXX
XXXXXXXXXXXXX
XXXXXXXXXXXXX
XXXXXXXXXXXXX
("XX" represents alphanumeric characters.)
◦
Print LAN details
You can print out the network settings of the machine such as its IP address and SSID.
For more information on the machine's network setting is printed out:
Printing Out Network Setting Information
Important
•
This printout contains valuable information about your computer. Handle it with care.
•
Other settings
Important
•
You cannot select the items below...

Service nameSpecifies the Bonjour service name. You can use up to 48 characters for the name.
Note
•
You cannot use the same service name as that already used for other LAN connected devices.
◦
LPR protocol setting
Activates/deactivates the LPR setting.
◦
Wireless LAN DRX setting
Selecting  Enable allows you to activate discontinuous reception when using wireless LAN. It allows
you to save electricity.
Note
•
Depending on the access point you are using, discontinuous reception may not be activated even...

Device user settings
Important
•
This setting item is for the administrator.
•
Date/time setting
Sets the current date and time.
Setting the Sender Information
•
Date display format
Sets the format of dates displayed on the touch screen and printed on sent faxes and photos.
Note
•
When  ON is selected for  Print date on the print settings screen in printing from a USB flash drive,
the shooting date is printed in the date display format you selected.
Setting Items for Photo Printing Using the Operation...