Canon Lv-7245, Lv-7240, Lv-x5 Multimedia Projector Users Manual

							13
2. Installation and Connections
WARNING
*Installing your projector on the ceiling must be done
by a qualified technician. Contact your dealer for more
information.
*Do not attempt to install the projector yourself.
•Only use your projector on a solid, level surface. If the
projector falls to the ground, you can be injured and
the projector severely damaged.
•Do not use the projector where temperatures vary
greatly. The projector must be used at temperatures
between 41˚F (5˚C) and 95˚F (35˚C).
•Do not expose the projector to moisture, dust, or
smoke. This will harm the screen image.•Ensure that you have adequate ventilation around your
projector so heat can dissipate. Do not cover the vents
on the side or the front of the projector.
Reflecting the Image
Using a mirror to reflect your projectors image enables
you to enjoy a much larger image. Contact your dealer if
you need a mirror system. If youre using a mirror sys-
tem and your image is inverted, use the MENU and
SELECT 
 buttons on your projector cabinet or
your remote control to correct the orientation. See page
40. 
						

							14
2. Installation and Connections
 Making Connections
NOTE: When using with a notebook PC, be sure to connect between the projector and the notebook PC before turning on the
power to the notebook PC. In most cases signal cannot be output from RGB output unless the notebook PC is turned on after
connecting with the projector.
*If the screen goes blank while using your remote control, it may be the result of the computers screen-saver or power
management software.
AC IN
ANALOG IN-1ANALOG IN-2
VIDEO INL   AUDIO IN   R
S-VIDEO IN
ANALOG IN-1
ANALOG IN-2
AUDIO OUTL   AUDIO IN   RMONO MONO
SERVICE PORTAUDIO INAUDIO IN 
PHONE
PHONE
Connecting Your PC or Macintosh Computer
NOTE: The COMPUTER 1 connector supports Plug & Play (DDC2).
VGA cable (supplied)To mini D-Sub 15-pin connector on the projector. It
is recommended that you use a commercially
available distribution amplifier if connecting a
signal cable longer than the supplied one.Audio cable
(not supplied)
IBM PC or Compatibles (Desktop type)
or Macintosh (Desktop type)
NOTE: For older Macintosh, use a
commercially available pin adapter
(not supplied) to connect to your
Macs video port.
IBM VGA or Compatibles (Notebook
type) or Macintosh (Notebook type)
Connecting your PC or Macintosh computer to your projector will enable you to project your computers screen image
for an impressive presentation.
To connect to a PC or Macintosh, simply:
1. Turn off the power to your projector and computer.
2. Use the supplied VGA cable to connect your PC or Macintosh to the projector.
3. Connect the supplied power cord. See page 19.
4. Turn on the projector and the computer.
5. If the projector goes blank after a period of inactivity, it may be caused by a screen saver installed on the computer
youve connected to the projector.
NOTE: Use an audio cable without a built-in resistor. Using an audio cable with a built-in resistor turns down the sound.
Enabling the computer’s external display
Displaying an image on the notebook PC’s screen does not necessarily mean it outputs a signal to the projector.
When using a PC compatible laptop, a combination of function keys will enable/disable the external display.
Usually, the combination of the ‘Fn” key along with one of the 12 function keys gets the external display to come on
or off. For more details, refer to your computer’s owner’s manual. 
						

							15
NOTE: An image may not be displayed correctly when a Video or S-Video source is played back via a commercially available scan
converter.
This is because the projector will process a video signal as a computer signal at the default setting. In that case, do the following.
*When an image is displayed with the lower and upper black portion of the screen or a dark image is not displayed correctly:
Project an image to fill the screen and then press the AUTO PC button on the remote control or the projector cabinet.
2. Installation and Connections
AC IN
VIDEO INL   AUDIO IN   R
S-VIDEO IN
ANALOG IN-1
ANALOG IN-2
AUDIO OUTL   AUDIO IN   RMONO MONO
SERVICE PORTAUDIO IN
ANALOG IN-1
Before connections: An exclusive Scart adapter (LV-CA35) and a commercially available Scart cable are required for
this connection.
NOTE: Audio signal is not available for this connection.
1. Turn off the power to the projector and your video equipment.
2. Use the LV-CA35 Scart adapter and a commercially available Scart cable to connect the RGB input of your projec-
tor and a Scart output (RGB) of your video equipment.
3. Connect the supplied power cord. See page 19.
4. Turn on the power to the projector and your video equipment.
5. Use the COMPUTER-1 button on the projector cabinet to select the ANALOG IN-1 input.
6. Press the MENU button on the projector cabinet to display the menu.
7. From the menu, select [Advanced settings] → [Signal select] → [Computer-1] → [Scart].
Scart is a standard European audio-visual connector for TVs, VCRs and DVD players. It is also referred to as Euro-
connector.
NOTE: The LV-CA35 Scart adapter is obtainable from your dealer in Europe. Contact your dealer in Europe for more information.
To connect Scart output (RGB)
Video equipment such as DVD player
Commercially available Scart cable
Female
LV-CA35
Projector
To ANALOG 1 input 
						

							16
2. Installation and Connections
Connecting an External Monitor
MONITOR OUTAUDIO
AC IN
VIDEO INL   AUDIO IN   R
S-VIDEO IN
ANALOG IN-1
ANALOG IN-2
AUDIO OUTL   AUDIO IN   RMONO MONO
SERVICE PORTAUDIO IN
(MONITOR OUT) 
You can connect a separate, external monitor to your projector to simultaneously view on a monitor the RGB analog
image youre projecting.
To  do so:
1. Turn off the power to your projector, monitor and computer.
2.
Use an VGA cable to connect your monitor to the MONITOR OUT (Mini D-Sub 15 pin) connector on your projector.
3. Connect the supplied power cord. See page 19.
4. Turn on the projector, monitor and the computer.
NOTE: Daisy chain connection is not possible.
NOTE: Use an audio cable without a built-in resistor. Using an audio cable with a built-in resistor turns down the sound.
VGA cable (supplied)
VGA cable (not supplied) 
						

							17
AUDIO INLR
AUDIO OUT
LR
Component
YCbCr
AC IN
ANALOG IN-1AUDIO IN 
VIDEO INL   AUDIO IN   R
S-VIDEO IN
ANALOG IN-1
ANALOG IN-2
AUDIO OUTL   AUDIO IN   RMONO MONO
SERVICE PORTAUDIO IN
2. Installation and Connections
You can connect your projector to a DVD player with component or composite video output. To do so, simply:
1. Turn off the power to your projector and DVD player.
2. If your DVD player has the component video (Y,Cb,Cr) output, use a commercially available component video cable
(RCA
3) and the optional 15-pin-to-RCA (female)
3 cable to connect your DVD player to the ANALOG IN con-
nector on the projector.
For a DVD player without component video (Y,Cb,Cr) output, use common RCA cables (not provided) to connect a
composite VIDEO output of the DVD player to the Video Input of the projector.
3. Connect the supplied power cord. See page 19.
4. Turn on the projector and DVD player.
A component signal will be automatically displayed. If not, from the menu, select [Advanced settings] → [Input
signal select] → [Computer], and then place a check mark in the COMPONENT radio button.
NOTE: Refer to your DVD players owners manual for more information about your DVD players video output requirements.
Connecting Your DVD Player with Component Output
DVD playerAudio Equipment
Audio cable (not supplied)
Optional 15-pin - to - RCA (female)
3 cable (LV-CA32)
Component video RCA
3
cable (not supplied) 
						

							18
2. Installation and Connections
AUDIO INLRAUDIO OUTLRVIDEO OUTS-VIDEO VIDEO
AC IN
VIDEO INL   AUDIO IN   R
S-VIDEO IN
ANALOG IN-1
ANALOG IN-2
AUDIO OUTL   AUDIO IN   RMONO MONO
SERVICE PORTAUDIO IN
S-VIDEO IN
VIDEO IN
AUDIO IN
AUDIO IN
Connecting Your VCR or Laser Disc Player
S-Video cable (not supplied)
Video cable (not supplied)
VCR/ Laser disc player
Audio equipment
Audio cable (not supplied)
Use an RCA or S-Video cable (not provided) to connect the video and use RCA cables (not provided) to connect the
audio from your VCR, laser disc player or document camera to your projector.
To make these connections, simply:
1. Turn off the power to the projector and VCR, laser disc player or document camera.
2. Connect one end of an RCA cable to the video output (or one end of an S-Video cable to the S-Video output
connector) on the back of your VCR or laser disc player, connect the other end to the appropriate video input
on your projector. Connect one end of a pair RCA cables (not supplied) to the audio output on the back of your
VCR or laser disc player, connect the other end to your audio equipment or to the appropriate audio input on
the projector.
Be careful to keep the right and left channel connections correct for stereo sound.
3. Connect the supplied power cord. See page 19.
4. Turn on the projector and the VCR or laser disc player.
NOTE: Refer to your VCR or laser disc player owners manual for more information about your equipments video output
requirements.
NOTE: An image may not be displayed correctly when a Video or S-Video source is played back in fast-forward or fast-rewind via
a scan converter. 
						

							19
2. Installation and Connections
AC IN
VOL-VO
L+
ZOOM
FOCUS
S
-V
ID
E
O
 IN
M
O
N
O M
O
N
O
V
ID
E
O
 INL   AUDIO IN   R
ANALOG IN-1
ANALOG IN-2
A
U
D
IO
 O
U
TL   AUDIO IN   R
S
E
R
V
IC
E
 
P
O
R
T A
U
D
IO
 IN
POWERV
ID
E
OS
-V
IDEOCOMPUTER-1 COMPUTER-2
W
A
R
N
I
N
GLA
M
P
 R
EP
LA
C
E
A
UTO
 PC
AC IN
Connecting the Supplied Power Cord
Connect the supplied power cord to the projector.
First connect the supplied power cords two-pin plug to the AC IN of the projector, and then connect the other plug of
the supplied power cord in the wall outlet.
Make sure that the prongs are fully inserted into
both the AC IN and the wall outlet. To wall outlet 
←
CAUTION:
Do not unplug the power cord from the wall outlet under any one of the following circumstances.
Doing so can cause damage to the projector:
•While the Hour Glass icon appears.
•While the cooling fans are running. The cooling fans continue to work for 30 seconds after the projector is
turned off.
•While the lamp is lighted. 
						

							20
3. Projecting an Image (Basic Operation)
This section describes how to turn on the projector and to project a picture onto the screen.

 Turning on the Projector
NOTE:
•The projector has two power switches: a main power switch and a POWER button.
•When plugging in or unplugging the supplied power cord, make sure that the main power switch is pushed to the off (
)
position. Failure to do so may cause damage to the projector.
AC IN
ZOOM
FOCUSWARNINGLAMP REPLACE POWER
1. To turn on the main power to the projector, press the
Main Power switch to the on position ( I ).
•The POWER indicator will light orange.
See the Power Indicator section on page 52 for more
details.
2. Press the POWER button on the projector cabinet or
the POWER button on the remote control for a
minimum of 2 seconds. The POWER indicator will
turn to green and the projector will become ready to
use.
After you turn on your projector, ensure that the
computer or video source is turned on and that your
lens cap is removed.
NOTE: When no signal is available, a blue, black or logo screen is
displayed.
When the projector displays a blue or a black screen (not logo),
the Quiet mode will be automatically selected in Lamp Mode.
NOTE: If you turn on the projector immediately after the lamp is
turned off or when the temperature is high, the fans runs without
displaying an image for some time and then the projector will
display the image.
POWERVIDEO S-VIDEOWARNINGLAMP REPLACE
VOL-VOL+
POWEROFF
NO SHOW
D.ZOOMPAGE
MENU
POWERPOWER
WARNING
LAMP REPLACE
WARNING
LAMP REPLACE
POWERWARNING
LAMP REPLACE
Standby Blinking Power On
Steady orange light Blinking  green
lightSteady green
light
See page 52 for more details. 
						

							21
POWERVIDEO S-VIDEOCOMPUTER-1 COMPUTER-2WARNINGLAMP REPLACE
AUTO PC
VOL-VOL+
3. Projecting an Image (Basic Operation)
Note on Startup screen (Menu Language Select screen)
When you first turn on the projector, you will get the Startup menu. This menu gives you the opportunity to select one
of the 8 menu languages.
To select a menu language, follow these steps:
1. Use the SELECT  or  button to select one of the
8 languages for the menu.
POWEROFF
NO SHOW
D.ZOOMPAGE
MENU
BACK
2. Press the OK button to execute the selection.
After this has been done, you can proceed to the menu opera-
tion.
If you want, you can select the menu language later. See Lan-
guage on pages 34 and 40.
POWERVIDEO S-VIDEOCOMPUTER-1 COMPUTER-2WARNINGLAMP REPLACE
AUTO PC
VOL-VOL+
POWEROFF
NO SHOW
D.ZOOMPAGE
MENU
BACK
NOTE: Immediately after turning on the projector, screen flicker may occur. This is normal. Wait 3 to 5 minutes until the lamp
lighting is stabilized.
When the Lamp mode is set to Quiet, the LAMP REPLACE indicator will light green.
If one of the following things happens, the projector will not turn on.
•If the internal temperature of the projector is too high, the projector will not turn on to protect the internal system.
Please wait for the projectors internal components to cool down.
•When the lamp reaches its end of usable life, the projector will not turn on. If this happens, replace the lamp.
•If the lamp fails to light, and if the WARNING indicator flashes on and off in a cycle of six times, wait a full minute and
then turn on the power. 
						

							22
3. Projecting an Image (Basic Operation)
 Selecting a Source
Selecting the computer or video source
VIDEO S-VIDEOCOMPUTER-1 COMPUTER-2POWERWARNINGLAMP REPLACE
AUTO PC
VOL-VOL+
RD-426E
1
2
R-CLICK L-CLICK
VIDEOCOMPUTER-1AUTO PC
VOLFREEZEINFO.
IMAGE ASPECT
COMPUTER-2S-VIDEO
NOTE: Turn on the computer or VCR connected to the projector.
Using the cabinet buttons
Press any one of the COMPUTER-1/-2, VIDEO and S-VIDEO buttons.
The corresponding indicator will light green.
Using the Remote Control
Press any one of the COMPUTER-1/-2, VIDEO or S-VIDEO buttons.