Canon Imageclass Mf7480 User Guide

Original and Paper
2‑14

Printable Area
The shaded area indicates the approximate printable area of LTR paper. Note that the 
margin widths listed are approximate and there may be slight variations in actual use.
 

2‑15
Original and Paper

Loading Paper
To load paper in the paper drawer, see “Set Up the Machine,” in the Starter Guide.
If you are making two‑sided prints, select the Two‑sided mode. The printed paper may crease depending on 
the moisture absorption condition of the paper, and if you copy the two pages as two one‑sided documents.
When printing on special types of paper, such as heavyweight paper or transparencies, be sure to correctly set 
the paper type, especially if you are using heavyweight paper....

Original and Paper
2‑16

1 Open the stack bypass.
If the paper size you are going to load into 
the stack bypass is different from the paper 
size stored in Stack Bypass Standard Settings, 
set Stack Bypass Standard Settings to [Off] 
in Common Settings (from the Additional 
Functions screen). (See “Setting Paper Size 
and Type for the Stack Bypass,” on p. 2‑21.)
2  Adjust the slide guides (A) to 
match the size of the paper.
If you are feeding large size paper, pull out 
the auxiliary tray (A), and...

2‑17
Original and Paper

To print on the back side of preprinted 
paper, load the preprinted paper face up 
into the stack bypass, as shown in the 
illustration below.
The screen for selecting the paper size 
appears.
When loading paper into the stack bypass, 
align the paper stack neatly between the 
slide guides. If the paper is not loaded 
correctly, a paper jam may occur.
If you are printing on heavyweight paper 
or envelopes using the stack bypass, and 
find that the paper or envelopes are not...

Original and Paper
2‑18

4 Hold down the four corners of the 
envelopes firmly, so that they and the 
sealed or glued portion stay flat.
`
Do not print on the back side of the 
envelopes (the side with the flap (A)).
If the envelopes become filled with air, 
flatten them by hand before loading 
them into the stack bypass.
–
–
5 Load the envelopes, as shown below.
FeedingDirection
The screen for selecting the paper size 
appears.
The stack bypass can hold 10 envelopes 
at a time.
Envelopes may be creased...

2‑19
Original and Paper

Setting Paper Size and Type
When you place other sizes and/or types of paper, follow this procedure to change the 
settings.
Setting Paper Type for the Paper Drawers
This setting enables you to specify the paper type loaded in each paper source.
Once you specify this information, icons indicating the type of paper loaded in each paper 
source appear on the paper select screen.
Be sure to correctly set the paper type. If the type of paper is not set\
 correctly, it could...

Original and Paper
2‑20

5 
① Select the paper source in which you want 
to register the paper type.
The numbers on the screen represent the 
following paper sources:
Paper Drawer 1Paper Drawer 2
6 
①  Select the desired paper type loaded in 
the paper source.
②  Press [OK].
Make sure that the registered paper type 
setting is the same paper type that is 
loaded in the paper source.
ƒƒ
ƒ
„
ƒ
„
7  Press [Done] repeatedly until the 
Basic Features screen appears.
The registered paper type...

2‑21
Original and Paper

Setting Paper Size and Type for the Stack Bypass
You can set the paper size and type that the stack bypass uses beforehand. This setting is 
useful if you always load the same paper size and type into the stack bypass.
When printing on special types of paper, such as heavyweight paper or transparencies, be sure to correctly set 
the paper type, especially if you are using heavyweight paper. If the ty\
pe of paper is not set correctly, it could 
adversely affect the quality of...

Original and Paper
2‑22

If you want to select a standard 
paper size:
1
① Select the desired paper size.
②  Press [Next].
To select an A or B series paper size, press 
[A/B‑size].
2
①  Select the desired paper type.
②  Press [OK].
When printing on special types of 
paper, such as heavyweight paper or 
transparencies, be sure to correctly 
set the paper type, especially if you 
are using heavyweight paper. If the 
type of paper is not set correctly, it 
could adversely affect the quality of 
the image....

2‑23
Original and Paper

When entering the value in millimeters, 
you can also change the value by 
pressing [‑] or [+] in increments of 
1.0 mm, even if you have entered the 
value.
If you enter a value outside the setting 
range, [OK] is grayed out and cannot be 
selected. Enter an appropriate value.
You can use values for [X] between 5 
7/8" (148 mm) and 17" (432 mm), and 
for [Y] between 3 3/4" (95 mm) and 11 
11/16" (297 mm).
3
4
① Select the desired paper type.
②  Press [OK].
When...