Canon I Sensys Mf8550cdn User Guide

0ALJ-08S
Configuring Ethernet Settings
Ethernet is  a standard for  communicating data in a local area network (LAN). You  can set the  communication
mode (half -duplex/full -duplex)  and  the  Ethernet type (10BASE-T/100BASE-TX). In general, the  machine can
be used without changing  the  defaults (
Ethernet Driver  Settings), but you can change these settings to
suit your network environment.
Press  .
Use  / to select ,  and  press  .
If  the  logon screen appears, enter the  correct ID and  PIN  using...

LINKS
Changing the Maximum Transmission  Unit
Setting a Wait Time for Connecting to a Network
>ß>ã>Þ>Ì>Û>Ì>â>ã>â
 

0ALJ-08U
Changing the Maximum Transmission Unit
In most Ethernet networks, the  maximum  size of a packet  that  can be sent is  1500  bytes.  A packet  refers to  a chunk  of data into which
the  original  data is  divided before being sent. The maximum  transmission unit  (MTU)  may  vary on  each network. Change  the  settings of
the  machine as necessary. For more information, contact your Network Administrator.
Press  .
Use  / to select ,  and  press  .
If  the  logon screen appears, enter the...

0ALJ-08W
Setting a Wait Time for Connecting to a Network
When  a network is  designed to  enjoy  redundant  connectivity with multiple switching hubs  or bridges, it must have a mechanism to
prevent  packets  from looping.  One  effective solution  is  to  define the  role of each switch  port. However, communication may  still be
disrupted  for  several tens of seconds  immediately  after you change the  way  that  network devices are  connected, or if  you add  a new
device. If  this type of problem...

0ALJ-08X
Configuring DNS
DNS (Domain  Name System) provides a service for  name resolution that  associates  a host  (or domain)  name with an  IP  address.
Configure the  DNS, mDNS,  or DHCP option settings as necessary. Note that  the  procedures for  configuring DNS are  different  for  IPv4
and  IPv6.
Start  the Remote UI  and  log  on in System Manager Mode.  Starting Remote UI
Click [Settings/Registration].
Click [Network Settings]  [TCP/IP  Settings].
Configure DNS settings.
Configuring IPv4 DNS...

[DNS  Settings][Primary DNS  Server Address]
Enter the  IP  address of a DNS server.
[Secondary DNS  Server Address]
Enter the  IP  address of a secondary DNS server, if  any.
[Host Name]
Enter up  to  47 alphanumeric  characters  for  the  host  name of the  machine that  is  to  be registered to  the  DNS server.
[Domain Name]
Enter up  to  47 alphanumeric  characters  for  the  name of the  domain  the  machine belongs to, such as "example.com."
[DNS  Dynamic  Update]
Select the  check  box to...

2Configure IPv6  DNS  settings.The [Use IPv6]  check  box must be selected to  configure the  settings.  
Setting IPv6  Addresses
[DNS  Settings]
[Primary DNS  Server Address]
Enter the  IP  address of a DNS server. Addresses that  start with "ff"  (or multicast address) cannot  be entered.
[Secondary DNS  Server Address]
Enter the  IP  address of a secondary DNS server, if  any. Addresses that  start with "ff"  (or multicast address) cannot  be
entered.
[Use Same  Host Name/Domain Name...

LINKS
Setting IPv4  Address
Setting IPv6  Addresses
Viewing Network Settings
>ß>ã>ä>Ì>Û>Ì>â>ã>â
 

0ALJ-08Y
Configuring SMB
Server  Message Block (SMB) is  a protocol for  sharing  resources, such as files  and  printers, with more than
one device in a network. The machine uses SMB to  store  scanned documents into a shared  folder.  Depending
on  your network, you may  have to  set the  NetBIOS  name and  workgroup name.
NetBIOS Name
In a Windows  network that  uses NetBIOS, NetBIOS  names  are  used for  identifying network-connected computers as well as for  file
sharing  and  other network...

Specify  the required settings  and  click [OK].
[NetBIOS Name]
Enter up  to  15 alphanumeric  characters  for  the  NetBIOS  name of the  machine.
[Workgroup Name]
Enter up  to  15 alphanumeric  characters  for  the  name of the  workgroup that  the  machine belongs to.
IMPORTANT:
NetBIOS  names  or workgroup names  that  start with an  asterisk  (*)  cannot  be registered to  a WINS server.
Restart the machine.
Turn  OFF  the  machine, wait  for  at least  10 seconds,  and  turn  it back ON.
LINKS...