Canon Eos Rebel T5i 700d Instruction Manual

31
The card (sold separately) can be an SD, SDHC, or SDXC memory 
card. SDHC and SDXC memory cards with UHS-I can also be used. 
The captured images are recorded onto the card.Make sure the card’s write-protect switch is set upward to 
enable writing/erasing.
1Open the cover.
 Slide the cover as shown by the 
arrows to open it.
2Insert the card.
 As shown by the  illustration, face 
the card’s label side toward you 
and insert it until it clicks in place.
3Close the cover.
  Close the cover and slide it...

32
Installing and Removing the Card
1Open the cover.
 Set the power switch to < 2>.
  Make sure the access lamp is off, 
then open the cover.
  If [Recording... ] is displayed, close 
the cover.
2Remove the card.
  Gently push in the card, then let go to 
eject it.
  Pull the card straight out, then close 
the cover.
Removing the Card
Access lamp
  When the access lamp is lit or blinking, it indicates that images are 
being written to or read by the card, being erased, or data is being 
transferred. Do...

33
After you flip out the LCD monitor, you can set menu functions, use Live 
View shooting, shoot movies, and play back images and movies. You 
can change the direction and angle of the LCD monitor.
1Flip out the LCD monitor.
2Rotate the LCD monitor.
  When the LCD monitor is swung out, 
you can rotate it up or down, or face it 
forward toward the subject.
  The indicated angle is only 
approximate.
3Face it toward you.
 Normally, face the LCD monitor 
toward you.
Using the LCD Monitor
180°
175°
90°
Be...

34
If you turn on the power switch and the time zone and date/time 
setting screens appear, see page 36 to set the time zone and date/
time. : The camera turns on. You can 
shoot movies (p.173).
< 1 > : The camera turns on. You can 
shoot still photos.
< 2> : The camera is turned off and 
does not operate. Set to this 
position when not using the 
camera.
  Whenever you set the power switch to < 1> or < 2>, sensor 
cleaning will be executed automat ically. (A small sound may be 
heard.) During the sensor...

35
Turning on the Power
When the power is turned on, the battery level will be indicated in one of four levels.z: Battery level is sufficient.
x : Battery level is low, but the 
camera can still be used.
c : Battery will be exhausted soon. 
(Blinks)
n : Recharge the battery.
Battery Life [Approx. number of shots]
 The figures above are based on a fully-charged Battery Pack LP-E8, no Live 
View shooting, and CIPA (Camera & Imaging Products Association) testing 
standards.
  Possible shots with Battery...

36
When you turn on the power for the first time or if the time zone and date/time 
have been reset, the Time zone and Date/Tim e setting screens will appear. 
Follow the steps below to set the time zone first. You can also set the time zone 
of your current address. Then if you travel to another time zone, you can simply 
set your destination’s time zone so that the correct date/time is recorded.
Note that the date/time appended to recorded images will be based 
on this date/time setting. Be sure to set...

37
3 Setting the Time Zone, Date and Time
3Set the date and time.
 Press the < U> key to select the 
date or time number.
  Press < 0> so < a> is displayed.
  Press the < V> key to set the 
number, then press < 0>. (Returns 
to < b>.)
4Set the daylight saving time.
  Set it if necessary.
  Press the < U> key to select [ Y].
  Press < 0> so < a> is displayed.
  Press the < V> key to select [ Z], 
then press < 0>.
  When the daylight saving time is set 
to [Z ], the time set in step 3 will 
advance by 1...

38
1Display the menu screen.
 Press the < M> button to display 
the menu screen.
2Under the [ 52] tab, select 
[Language K].
  Press the < U> key to select the 
[5 2] tab.
  Press the < V> key to select 
[Language
K] (the sixth item from 
the top), then press < 0>.
3Set the desired language.
  Press the < S> key to select the 
language, then press < 0>.
X The interface language will change.
3  Selecting the Interface Language
COPY  

39
The camera is compatible with all Canon EF lenses and EF-S lenses. The camera cannot be used with EF-M lenses.
1Remove the caps.
 Remove the rear lens cap and the 
body cap by turning them as shown 
by the arrows.
2Attach the lens.
 Align the lens’ red or white index with 
the camera’s index matching the 
same color. Turn the lens as shown 
by the arrow until it clicks in place.
3Set the lens focus  mode switch to 
.
   stands for Autofocus.
  If it is set to  (manual focus), 
autofocus will not...

40
Attaching and Detaching a Lens
To zoom, turn the zoom ring on the lens 
with your fingers.
If you want to zoom, do it before 
focusing. Turning the zoom ring after 
achieving focus may throw off the 
focus.
While pressing the lens release 
button, turn the lens as shown by 
the arrows.
 Turn the lens until it stops, then 
detach it.
  Attach the rear lens cap to the 
detached lens.
About Zooming
Detaching the Lens
  Do not look at the sun directly th rough any lens. Doing so may cause 
loss of...