Canon Eos Rebel T3i 600d Instruction Manual

21
Nomenclature
Viewfinder Information
The display will show only the settings currently applied.
ApertureAF point activation indicator 
< >
AF points

ISO speed
 Focus 
 confirmation
 light
Max. burst  
White balance 
correction
ISO speed
 Monochrome shooting
Exposure level indicator
  Exposure compensation amount
 AEB range
Red-eye reduction lamp-on indicator
Card full warning  (FuLL)
Card error warning (Card)
No card warning ( Card)
 AE lock/
AEB in-progress
 Flash-ready Improper FE lock 
warning...

Nomenclature
22
Mode Dial
The Mode Dial includes the Basic Zone modes, Creative Zone modes, 
and the Movie shooting mode.
Basic Zone
All you do is press the shutter button.
The camera sets everything to suit the 
subject.
A :Scene Intelligent Auto (p.50)
7 :Flash Off (p.55)
C :Creative Auto  (p.56)
Creative Zone
These modes give you more control for 
shooting various subjects.
d
: Program AE (p.74)
s : Shutter-priority AE (p.94)
f : Aperture-priority AE (p.96)
a : Manual exposure (p.99)
8 : Automatic...

23
Nomenclature
Lens
Lens without a distance scale
Lens with a distance scale
Focus mode switch (p.36)
Lens mount index  (p.36) Contacts (p.15)
Hood mount 
(p.294)
Filter thread 
(front of lens) (p.294) Focusing ring (p.87,138)
Zoom ring (p.37)
Zoom position index (p.37)
Image Stabilizer switch  (p.38)
Focus mode switch (p.36)
Focusing ring (p.87,138)
Image Stabilizer switch  (p.38)
Hood mount 
(p.294)
Filter thread 
(front of lens) (p.294) Zoom ring (p.37)
Contacts (p.15)
Lens mount index  (p.36)
Zoom...

Nomenclature
24
Battery Charger LC-E8
Charger for Battery Pack LP-E8 (p.26).
Battery Charger LC-E8E
Charger for Battery Pack LP-E8 (p.26).
Battery pack slotPower plug
Charge lamp
Full-charge lamp
IMPORTANT SAFETY INSTRUCTIO NS-SAVE THESE INSTRUCTIONS.
DANGER-TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, 
CAREFULLY FOLLOW THESE INSTRUCTIONS.
For connection to a supply  not in the U.S.A., use an attachment plug adapter 
of the proper configu ration for the power outlet, if needed.
Power cord 
Power cord...

25
Getting Started
This chapter explains preparatory steps before you start 
shooting and basic camera operations.
Attaching the Strap
Pass the end of the strap through 
the camera’s strap mount eyelet 
from the bottom. Then pass it 
through the strap’s buckle as shown 
in the illustration. Pull the strap to 
take up any slack and make sure 
the strap will not loosen from the 
buckle.
 The eyepiece cover is also 
attached to the strap (p.262).
Eyepiece cover
COPY  

26
1Remove the protective cover.
 Detach the protective cover provided 
with the battery.
2Attach the battery.
 As shown in the illustration, attach the 
battery securely to the charger.
  To detach the battery, follow the 
above procedure in reverse.
3Recharge the battery.
For LC-E8
 As shown by the arrow, flip out the 
battery charger’s prongs and insert 
the prongs into a power outlet.
For LC-E8E
 Connect the power cord to the 
charger and insert the plug into the 
power outlet. 
X Recharging starts...

27
Charging the Battery
 Upon purchase, the batter y is not fully charged.
Recharge the battery before using.
  Recharge the battery on the day before or on the day it is to be 
used.
Even during storage, a charged battery will gradually drain and lose 
its power.
  After recharging the battery, de tach it and unplug the charger 
from the power outlet.
  When not using the camera, remove the battery.
If the battery is left in the came ra for a prolonged period, a small 
amount of power current is releas...

28
Load a fully charged Battery Pack LP-E8 into the camera.
1Open the cover.
 Slide the lever as shown by the 
arrows and open the cover.
2Insert the battery.
 Insert the end with the battery 
contacts.
  Insert the battery until it locks in 
place.
3Close the cover.
 Press the cover until it snaps shut.
Open the cover and remove the 
battery.
 Press the battery release lever as shown 
by the arrow and remove the battery.
 To prevent short circuiting of the 
battery contacts, be sure to attach the...

29
The card (sold separately) can be an SD, SDHC, or SDXC memory 
card. The captured images are recorded onto the card.Make sure the card’s write-protec t switch is set upward to 
enable writing/erasing.
1Open the cover.
 Slide the cover as shown by the 
arrows to open it.
2Insert the card.
 As shown by the illustration, face 
the card’s label side toward you 
and insert it until it clicks in place.
3Close the cover.
 Close the cover and slide it in the 
direction shown by the arrows until it 
snaps...

Installing and Removing the Card
30
1Open the cover.
 Set the power switch to .
  Make sure the access lamp is off, 
then open the cover.
  If “Recording ...” is displayed, close 
the cover.
2Remove the card.
 Gently push in the card, then let go. 
The card will stick out.
  Pull the card straight out, then close 
the cover.
Removing the Card
Access lamp
 When the access lamp is lit or blin king, it indicates that images are 
being written to or read by the ca rd, being erased, or data is being...